Abstract:Fast charging is critical for the efficient storage of energy in devices like electric vehicles and portable electronics. The rate performance of electrodes is limited by the electron transfer rate, the ohmic resistance of the electrode, the size and shape of the primary electrode particles, and the charge carrier diffusion process within the electrodes. However, separating the intrinsic contributions of mass transport and charge transfer from non-equilibrium data obtained under large interfacial polarization is very complex, which limits our understanding of high rate electrodes during charging and discharging. While it is possible to extract the diffusive and capacitive components of an electrode’s capacity from cyclic voltammetry (CV) data using the Dunn method, the Dunn model assumes a constant diffusional overpotential. In reality the ohmic resistance scales with the current, so that the ohmic potential drop across the electrode cannot be neglected a priori for fast charging electrodes in which high current densities are a requirement. We recently developed a new model based on the Butler-Volmer equation for the kinetics of the electron exchange process, and incorporated the charge carrier diffusion process and the internal ohmic losses, as well as the effect of the shape and dimensions of the primary electrode particles on the effective diffusion rate [1]. The model can provide the relation between current peak voltages and peak currents from a series of sweep rate CV measurements. The ohmic resistance, equilibrium voltage, exchange current (related to the electrochemical reaction rate) and limiting current (related to the charge carrier diffusion coefficient and Nernst diffusion layer thickness) can be extracted as independent variables from the fitted experimental data. By simulating a range of different high rate Li electrode materials (both cathodes and anodes), we identified influence of the reaction rate on the overpotential as a common significant factor, which explains the nonlinear relation between the potential and the current at peak position in different CV measurements. Our analysis suggests that a higher electrochemical reaction rate seems to be more important for the realization of faster charging batteries than a larger carrier diffusion coefficient. Finally, our extended model also enables us to predict the overpotential at any applied potential, which is not possible with other current models known till date. This insight helps us to gain more detailed understanding of the relationship between the intrinsic properties of the electrode materials and their rate performance in different reaction stages. This may facilitate further modification of electrode material towards enhanced high rate performance in next-generation batteries. [1] R. Xia et al., Energy Storage Mater. 53 (2022) 381-390.

Electrode Passivation by Phenolic Compounds: Modeling Analysis

Potential Drop Based Model to Analyze Electrode Passivation by Fouling from Phenolic Compounds

RETRACTED: Copper Electrodeposition in Through-Silicon Via under Galvanostatic Condition

Electrochemical investigation of copper passivation kinetics and its application to low-pressure CMP modeling

Fundamental Mechanisms of Copper CMP – Passivation Kinetics of Copper in CMP Slurry Constituents

Characterization of Surface Fouling of Ti/IrO2 Electrodes in 4-Chlorophenol Aqueous Solutions by Electrochemical Impedance Spectroscopy

Modeling Two-Phase Transport on the PEM Water Electrolyzer

The passivation mechanism of Fe in the acidic AlCl3-EMIC ionic liquid

Analysis of the Kinetics of Electrochemical Migration on Printed Circuit Boards Using Nernst-Planck Transport Equation

Effect of acid on passivation of a copper electrode in LiCF3SO3/propylene carbonate in underpotential region

Electrocatalysis aqueous phenol with carbon nanotubes networks as anodes: Electrodes passivation and regeneration and prevention

Linear dependence of potential drop at the passive film/solution interface on film-formation potential and pH: Combining first-principles calculations with experiments

Modeling of Pt Degradation in Polymer Electrolyte Fuel Cells: Effect of Electrode Potential Cycles

A Carbon Corrosion Model to Evaluate the Effect of Steady State and Transient Operation of a Polymer Electrolyte Membrane Fuel Cell

Dielectric Analysis of Dynamic Fouling Behavior on Surface of Polyethersulfone Composite Ultrafiltration Membrane

Electrochemical Corrosion of Electrode Equipment in Food Processing Device Using FEF Technology

Decoupling Reaction, Diffusion and Ohmic Processes in Fast-Charging Electrodes: A New Model for CV Data Analysis

Modeling of Membrane Electrode Assembly of PEM Fuel Cell to Analyze Voltage Losses Inside

Modeling of Potential Oscillation during Galvanostatic Electrooxidation of Formic Acid at Platinum Electrode

Electrochemical Pressure Impedance Spectroscopy for Polymer Electrolyte Membrane Fuel Cells: Signal Interpretation

Understanding of 3D hierarchically porous carbon modified electrode based on finite element modeling