Abstract:Selective laser melting (SLM) of SiC/Al-Si-Mg composites hold tremendous potential for engineering applications. However, there has been a lack of systematic research on their heat treatment patterns. This paper utilizes the Box-Behnken response surface method to establish a relationship model between SLM process parameters and the relative density of the 10 wt%SiC/AlSi10Mg composite. Simultaneously, 300 degrees C, 400 degrees C, and 500 degrees C treatments (T300, T400, T500) were used to investigate the porosity, microstructure, and mechanical properties of the 10 wt%SiC/AlSi10Mg composite. The results indicate that optimal process parameters were laser power of 331 W, scanning speed of 1243 mm/s, and hatching spacing of 120 mu m. Under these process parameters, the fabricated samples exhibited a relative density of over 99 % and presented a refined microstructure. The porosity of the as-built (AB) samples remained at a low level of similar to 0.38 %, while the porosity of T300, T400, T500 samples increased to similar to 0.7 %, similar to 0.78 %, similar to 0.92 %, respectively. Pores at the molten pool boundary (MPB) of the AB samples expanded into the melt pool inner (MPI) of the T300-T500 samples. The addition of SiC reinforcement significantly improved the strength and hardness of the composite materials, reaching 471 MPa and 151 HV, respectively. After heat treatment, the original fine network microstructure was disrupted due to the fracture, spheroidization growth, and coarsening of the eutectic networks. The elongation of the composite after heat treatment increased substantially from 3 % to 5.95 %, with a decrease in hardness and strength, a transition from brittle to ductile fracture behavior.

Effects of Surface-Oxidation Modification and Heat Treatment on Silicon Carbide 3d/alcu 5 MgTi Composites During Vacuum-Pressure Infiltration

The Effect of Surface Oxidized Modification on the Mechanical Properties of SiC3D/Al

Effect of Heat Treatment on the Interfacial Bonding Between SiC Coating and Alumina Plate

Effect of Interfacial Modification on Mechanical Properties of the Co-continuous SiC/Al Composites

Effect of heat treatment on mechanical properties of SiC/Ti-6Al-4V composites

Effect of heat treatment on tensile deformation behavior of SiCp/Al composites

Microstructure and mechanical properties of the α-SiAlON/α-SiC composites: Effects of heat treatment

Microstructure And Oxidation Resistance Of Carbon/Carbon Composites Coated With Si3n4-Si/Mosi2-Sic Multi-Layers By Slurry Coating And Post Heat-Treatment Process

Effect of Oxidization of 3D-Sic Preforms on the Interfacial Structure and Mechanical Properties of Co-Continuous SiC/Al Composites

Thermal Expansion and Oxidation of 3D C/SiC Composites with Different Coatings from Room Temperature to 1400°C

The Influencing Mechanism of Modification Layer on the Performance of Sic3d/Al Multi-Function Gradient Composite

Effect of Solution and Aging Treatment on the Microstructure and Tensile Properties of SiCf/C/Mo/Ti2AlNb Composites

Microstructure characterization and mechanical properties of in situ synthesized Ti2(Al,Si)C reinforced Al composites

The Effects of CVD SiC Interphase on Mechanical Properties of KD-1 SiC Fiber Reinforced Aluminum Phosphate Composites

Interfacial Bonding of Al-Si/C Composites and Improvement of the Thermal Shock Resistance

Effect of Heat Treatment Patterns on Microstructure and Mechanical Properties of Selective Laser Melting Fabricated SiC/AlSi10Mg Composite

Effect of Heat-Treatment on Stress Relief and Dimensional Stability Behavior of SiCp/Al Composite with High SiC Content

Microstructure And Mechanical Properties Of The Alpha-Sialon/Alpha-Sic Composites: Effects Of Heat Treatment

Regulating the Mechanical Properties of (μm B4C+nm SiC)/7075Al Composites Via Nano-Sic Content

Effect of the Heat Treatment Process on the Properties of SiCp/AL Composites

Effects of SiC Content on the Mechanical and Thermophysical Properties of 3D Cf/SiC–Al Composites