Abstract:Ag nanoparticles (NPs) were uniformly immobilized in hierarchically porous monolithic silica using. gamma-(aminopropyl) triethoxysilane (APTES) as a modifier and ethanol as a reductant, where the silica monolith was pre-prepared via the sol-gel accompanied by phase separation. Ag NPs embedded in the hierarchically porous silica monoliths were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), mercury porosimetry, nitrogen adsorption/desorption analysis, and X-ray photoelectron spectroscopy (XPS). The mechanism of the modification by APTES, the reduction using ethanol, and pore structure changes of the silica monolith after immobilization of Ag NPs are discussed. The results show that APTES modifies the monolith by incorporating amino groups onto the surface of the meso-macroporous skeletons, and then amino groups react with silver ions to form a silver-amine complex. Ethanol used as an effective reductant is adopted to promote the reduction process of the silver-amine complex. Ag NPs with an average size of approximately 16 nm were homogeneously supported on both the macroporous skeletons and in the mesopores of the silica monolith with good dispersion. The embedding of Ag NPs did not spoil the macroporous skeleton of the monolithic silica, and the surface area decreased from 418 to 254 m(2).g(-1) after introducing Ag NPs into its macro-mesopores. It was also found that the loading amount of Ag NPs increased with repeated modification and reduction treatments.

High density silanization of nano-silica particles using γ-aminopropyltriethoxysilane (APTES)

Preparation of amine functionalized silica by the one-step in spray drying system

Behavior of epoxy resin filled with nano-SiO<sub>2</sub> treated with a Eugenol epoxy silane

Process and mechanism of surface modification of silica with silane coupling agent APTS

Surface Amination of Silica Nanoparticles Using Tris(hydroxymethyl)aminomethane

Amination of silica nanoparticles using aminobutanol to increase surface reactivity

Modification of Nanosilica Particles with Hydrophobic Modifier Bis[3-(Triethoxysilyl)propyl]tetrasulfide by Using Micro-Injection in Aqueous Solutions

Coupling of synthesis and modification to produce hydrophobic or functionalized nano-silica particles

Preparation of Grafted SiO_2-g-PMAA Particles with High Grafting Degree via a Surface-initiated Graft Polymerization Method

Study on preparation and surface modification of precipitated silica obtained from fly ash

Facile Preparation of Silver Nanoparticles Homogeneously Immobilized in Hierarchically Monolithic Silica Using Ethylene Glycol As Reductant

Preparation of acrylate polymer/silica nanocomposite particles with high silica encapsulation efficiency via miniemulsion polymerization

Modification and Dispersion of Nanosilica

Study on Modification and Dispersion of Nano‐silica

Investigation of γ-Aminopropyltriethoxysilane (APTES)-Modified Halloysite Nanotubes on the Reinforcement of Halloysite/Polypropylene (PP) Nanocomposites

Preparation of high-strength silica aerogels by two-step surface modification via ambient pressure drying

Functionalized Si3N4 nanoparticles modified with hydrophobic polymer chains by surface-initiated atom transfer radical polymerization (ATRP)

Preparation and Characterization of Ag Nanoparticles Embedded in Hierarchically Porous Monolithic Silica

Preparation of dense modified nanosilica superhydrophilic coatings on aluminum alloy surfaces by adjusting amino groups

Surface Modification to Produce Hydrophobic Nano-Silica Particles Using Sodium Dodecyl Sulfate As a Modifier

Fabrication of silica nanoparticles on the surface of functionalized multi-walled carbon nanotubes