Silicalite-1@Cu-ZSM-5 core-shell catalyst for N2O decomposition

Tao Meng,Nan Ren,Zhen Ma

DOI: https://doi.org/10.1016/j.molcata.2015.05.006

2015-01-01

Abstract:•Silicalite-1@Cu-ZSM-5 is more active than conventional Cu-ZSM-5 in N2O decomposition.•Silicalite-1@Cu-ZSM-5 has more dimetric Cu+ upon thermal pretreatment in He.•Less O2 is adsorbed on Silicalite-1@Cu-ZSM-5.•Both factors contribute to the high activity of Silicalite-1@Cu-ZSM-5.

What problem does this paper attempt to address?

Catalytic Decomposition of N2O over Cu-ZSM-11 Catalysts

Pengfei Xie,Zhen Ma,Haibo Zhou,Chengyun Huang,Yinghong Yue,Wei Shen,Hualong Xu,Weiming Hua,Zi Gao

DOI: https://doi.org/10.1016/j.micromeso.2014.02.044

IF: 5.876

2014-01-01

Microporous and Mesoporous Materials

Abstract:The catalytic decomposition of N2O was investigated over a series of Cu-ZSM-11 catalysts with different Si/Al ratios. The physicochemical properties of the catalysts were characterized by XRD, N-2 adsorption, SEM, Al-27 MAS NMR, DRIFTS, XPS, and H-2-TPR. These catalysts were found to be effective for N2O decomposition. The catalytic activity in terms of conversion decreases when the Si/Al ratio increases, due to the decreased amount of active Cu+ species and the weakened reducibility of active sites. A comparison of Cu-ZSM-11 and Cu-ZSM-5 with the same Si/Al ratio demonstrates that Cu-ZSM-11 is apparently more active than Cu-ZSM-5, due to the enhanced reducibility of active Cu+ species and better accessibility of active sites in Cu-ZSM-11. (C) 2014 Elsevier Inc. All rights reserved.
Regulating the Microenvironments and the D-Band Center of Hierarchical Nimos/Ts-1 Catalyst by Zro2 to Enhance the Hydrodesulfurization Performance of Dibenzothiophene

Fei Fan,Shiyu Han,Ying Li,Lu Qi,Jie Kang,Zhiping Chen,Chang Tian,Dechao Wang,Wenwu Zhou

DOI: https://doi.org/10.1016/j.seppur.2024.128702

IF: 8.6

2025-01-01

Separation and Purification Technology

Abstract:The microenvironments including the surface hydroxyls, the oxygen vacancies, and the d-band center of hierarchical TS-1 zeolite pickled by hydrochloric acid were regulated by ZrO2, the effect of ZrO2 on the physicochemical properties and the catalytic performances of the corresponding NiMoS supported catalysts were studied. The experimental and theoretical calculation results show that the d-band center, the surface hydroxyl groups, and the oxygen vacancies were regulated after incorporation of ZrO2. Resulting in the modulated acidity of the support and the metal support interaction of the catalysts, further promoting the formation of type-II NiMoS active phases. The catalytic performance evaluations show that catalyst NiMo/1-ZAT exhibits the superior HDS performance, kinetic study further demonstrated that the enhanced catalytic activity was mainly contributed by the improved direct desulfurization activity generated from the moderate support acidity, suitable MSI, highest sulfidation degrees, most type-II NiMoS active phase and highest activity of individual active sites.
CoZSM-11 Catalysts for N2O Decomposition: Effect of Preparation Methods and Nature of Active Sites

Pengfei Xie,Yajun Luo,Zhen Ma,Liying Wang,Chengyun Huang,Yinghong Yue,Weiming Hua,Zi Gao

DOI: https://doi.org/10.1016/j.apcatb.2015.01.027

2015-01-01

Abstract:CoZSM-11 catalysts prepared using different methods (i.e., wet ion exchange, buffered ion exchange, semi-continuous ion exchange, and impregnation) were tested in N2O decomposition. For CoZSM-11 catalysts prepared by wet ion exchange, the activity increased with the decrease of the Si/Al ratio. Even higher activities can be achieved using catalysts prepared by buffered ion exchange or semi-continuous ion exchange. In contrast, CoZSM-11 prepared by impregnation was the least active. The catalysts were characterized by XRD, N-2 sorption, ICP,(27)AlMAS NMR, H-2-TPR, XPS, and UV-vis DRS. It was concluded that isolated Co2+ cations, in particular alpha-type Co2+, were active sites, whereas the CoOx species obtained by impregnation was much less active. The catalytic performance of CoZSM-11 and CoZSM-5 was compared as well. (C) 2015 Elsevier B.V. All rights reserved.
Catalytic Decomposition of N2o over Cu-Zsm-5 Nanosheets

Zou Wei,Xie Peng-Fei,Li Xu-Guang,Kong De-Jin,Hua Wei-Ming,Yue Ying-Hong,Gao Zi

DOI: https://doi.org/10.1016/j.molcata.2014.07.004

2014-01-01

Journal of Molecular Catalysis A Chemical

Abstract:ZSM-5 nanosheets were prepared using [C18H37-N+(CH3)2-C6H12-N+(CH3)2-C6H13]Br2 as a template and then ion-exchanged with Cu cations. The catalytic performance of the obtained Cu-ZSM-5 nanosheets in N2O decomposition was investigated and compared with that of conventional Cu-ZSM-5. Higher activity as well as better stability was observed for Cu-ZSM-5 nanosheets although the Cu contents of the catalysts were identical. Relevant characterization was conducted using XRF, ICP, XRD, N2 adsorption–desorption, SEM, TEM, CO-IR, H2-TPR and O2-TPD. The data show that the better catalytic performance of Cu-ZSM-5 nanosheets is probably due to better accessibility of active sites, better reducibility of active Cu+ species, and the weakened interaction between oxygen and Cu+ sites.
Effect of copper precursors on the catalytic performance of Cu-ZSM-5 catalysts in N2O decomposition

Tao Meng,Nan Ren,Zhen Ma

DOI: https://doi.org/10.1016/j.cjche.2018.02.015

IF: 3.8

2018-01-01

Chinese Journal of Chemical Engineering

Abstract:Five Cu-ZSM-5 catalysts were obtained by treating Na-ZSM-5 (Si/Al ratio=15) with aqueous solutions of different Cu precursors (CuCl2, Cu(NO3)2, CuSO4, Cu(CH3COO)2, and ammoniacal copper (II) complex ion). After being pretreated in flowing He at 500°C to form active Cu+, these catalysts exhibited quite different activities in catalytic decomposition of N2O. CZM-AC(II) (prepared by ammoniacal copper (II) complex ion) with 9.4wt% Cu content was the most active among these Cu-ZSM-5 catalysts, achieving almost complete N2O conversion at 400°C. CZM-CA (prepared using Cu(CH3COO)2 as the Cu precursor) with 2.8wt% Cu content was the second most active catalyst among these Cu-ZSM-5 catalysts, achieving almost complete N2O conversion at 425°C. CZM-CC, CZM-CN, and CZM-CS prepared by using CuCl2, Cu(NO3)2, or CuSO4 as the Cu precursor with similar Cu contents (≈1.7wt%) were the least active among these Cu-ZSM-5 catalysts, achieving ca. 90% N2O conversion at 500°C. XRD, ICP, SEM, TEM, EDX-mapping, and CO-IR experiments were conducted to characterize relevant samples. The superior activity of CZM-AC(II) can be attributed to the high contents of total Cu+ and dimeric Cu+ among these samples. The influence of co-fed O2 or H2O on the catalytic performance of typical samples was also studied.
Sustainable Synthesis of Core-shell Structured ZSM-5@Silicalite-1 Zeolite

Luan Huimin,Wu Qinming,Zhang Jian,Wang Yeqing,Meng Xiangju,Xiao Feng-Shou

DOI: https://doi.org/10.1007/s40242-021-1288-y

IF: 3.1

2021-01-01

Chemical Research in Chinese Universities

Abstract:C ore-shell structured ZSM-5@Silicalite-1 zeolite could effectively hinder the deactivation of catalyst surface. Currently, organic structure directing agents(OSDAs) are necessary in the conventional route for the synthesis of this core-shell zeolite under hydrothermal conditions, which is costly and environmental-unfriendly. In this research, a synthesis of the core-shell structured ZSM-5@Silicalite-1 zeolite with a strategy of alcohol filling and zeolite seeding without any organic template or solvent is exhibited. The obtained products are well characterized by X-ray powder diffractometer(XRD), scanning electron microscopy(SEM), transmission electron microscopy(TEM), N 2 sorption isotherms, solid magic angle spinning(MAS) NMR, temperature-programmed-desorption of ammonia(NH 3 -TPD), and X-ray photoelectron spectroscopy(XPS) techniques, in order to confirm the core-shell structure. More importantly, the core-shell structured ZSM-5@Silicalite-1 zeolite exhibits a long lifetime and a high p -xylene selectivity in the alkylation of toluene with methanol, compared with the conventional ZSM-5 catalyst.
Optimization of Conditions for Preparation of ZSM-5@silicalite-1 Core–shell Catalysts Via Hydrothermal Synthesis

Chuang Liu,Yihua Long,Zhengbao Wang

DOI: https://doi.org/10.1016/j.cjche.2018.03.030

IF: 3.8

2018-01-01

Chinese Journal of Chemical Engineering

Abstract:Although the preparation of ZSM-5@silicalite-1 (ZS) core-shell catalysts has been reported in the literature, their selectivity to pars-xylene (PX) in the toluene alkylation with methanol is difficult to control. Here we present the effects of water and ZSM-5 adding amounts in the synthesis solution, the hydrothermal synthesis time, and the Si/Al ratio of core ZSM-5 on the catalytic performance of ZS core-shell catalysts. The ZS core-shell catalysts were characterized by X-ray diffraction (XRD), N-2 adsorption, and NH3 temperature-programmed desorption (NH3-TPD) techniques. The highest PX selectivity of 95.5% was obtained for the ZS (Si/Al = 140) catalyst prepared in the synthesis solution with a molar ratio of 0.2TPAOH:1TEOS:250H(2)O at 175 degrees C and 10 r.min(-1) for only 2 h and the corresponding toluene conversion is as high as 22.8% for the alkylation of toluene with methanol. (C) 2018 The Chemical Industry and Engineering Society of China, and Chemical Industry Press. All rights reserved.
Decomposition of nitrous oxide over Co-zeolite catalysts: role of zeolite structure and active site

xinyan zhang,qun shen,chi he,chunyan ma,jie cheng,zhiming liu,zhengping hao

DOI: https://doi.org/10.1039/c2cy00465h

IF: 6.177

2012-01-01

Catalysis Science & Technology

Abstract:A series of Co exchanged zeolites with ZSM-5, BEA, MOR and USY structures were prepared and investigated for N2O catalytic decomposition under identical reaction conditions. It is found that Co-zeolites with different structures show dramatically different catalytic activities, which could be attributed to various Co species formed in them. Co-ZSM-5, Co-BEA and Co-MOR exhibit much higher activities than Co-USY catalysts, which is attributed to the predominant formation of active isolated Co2+ ions in the ion exchange positions; while in Co-USY Co mainly exists as less active Co oxides. Moreover, it is observed that the activities of Co2+ ions in ZSM-5, BEA and MOR zeolites are quite different and are related to the specific Co ion sites presented in each zeolite structure. In Co-ZSM-5, the most active sites are the alpha-type Co ions, which are weakly coordinated to framework oxygens in the straight channel. On the other hand, in Co-BEA and Co-MOR, the most active sites are beta-type Co ions, which are coordinated to the framework oxygens of the elongated six-membered ring of BEA and the interconnected small channel of MOR, respectively. The main factors affecting the activities of these individual Co ions are indicated to be their location in the zeolite structure, their chemical coordination and the distances between the Co ions. The highest activity of the alpha-type Co ions in ZSM-5 could be attributed to their favorite location in the zeolite and weak coordination to framework oxygens, which make them easily accessible and coordinated to reactants. The large number of beta-sites and their structural arrangement in MOR allow the formation of two unique adjacent beta-Co ions in Co-Co pairs, which cooperate in N2O splitting, consequently yielding the high activity of beta-Co ions in MOR.
Synthesis and Characterization of ZSM-5/Silicalite-1 Core-Shell Zeolite with a Fluoride-Containing Hydrothermal System

Weiyi Tong,KONG Dejin,Zhicheng Liu,GUO Yanglong,FANG Dingye

DOI: https://doi.org/10.3321/j.issn:0253-9837.2008.12.012

IF: 16.5

2008-01-01

Chinese Journal of Catalysis

Abstract:Cylindrical ZSM-5 was used as a core material, then its surface was pretreated with citric acid, and finally a secondary growth was performed in a system containing fluoride to form core-shell zeolite. The obtained products were characterized by XRD, SEM, TEM, N-2 adsorption, and NH3-TPD. The performance was investigated by probe reactions of toluene disproportionation and 1,3,5-trimethyl benzene cracking. The results obtained proved the formation of a micro-composite with a ZSM-5 core and a poly nano-silicalite-1 shell. The core ZSM-5 showed a compact shell by intergrowth in a fluoride way. The silicalite-1 shell almost reached 97% coverage with a decreased surface acidity and a preservation of the original channel acidity.
Promising Strategy to Synthesize ZSM-5@Silicalite-1 with Superior Catalytic Performance for Catalytic Cracking Reactions

Hongyu Shen,Min Liu,Junjie Li,Xiujie Li,Sujuan Xie,Fucun Chen,Longya Xu,Xinwen Guo,Chunshan Song,Xiangxue Zhu

DOI: https://doi.org/10.1021/acs.iecr.1c01043

2021-06-21

Abstract:The core–shell with regular morphology was prepared through an innovative tandem synthesis strategy for the first time, which combined the insertion of almost all aluminum sites by organotemplate-free synthesis and the sequential crystallization of residual silica sites by organotemplate-oriented synthesis. Samples with different Si and Al distributions could be synthesized by adjusting the tandem synthesis process, including temperature, time, Na2O/SiO2, etc. The obtained Si-rich-ZSM-5 and conventional C-ZSM-5 with a similar Si/Al ratio but different Al distributions, which were demonstrated by X-ray fluorescence (XRF), X-ray photoelectron spectroscopy (XPS), Transmission electron microscopy (TEM), and 1,3,5-triisopropylbenzene catalytic cracking analysis, were employed in n-hexane catalytic cracking reaction. Si-rich-ZSM-5 showed a higher stability with a n-hexane conversion of 57.7% at 100 h compared with that of C-ZSM-5 (24.6%), which was attributed to its inactive outer shell. Besides, a high para-xylene selectivity in xylene for the Si-rich-ZSM-5 catalyst was obtained. Hence, this study provides a simple and cost-effective strategy to fabricate highly stable catalysts for cracking reactions.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acs.iecr.1c01043?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acs.iecr.1c01043</a>.Discussions of materials and synthetic methods used, tables of synthesis conditions, physicochemical properties, and number of acid sites of different ZSM-5 samples, and figures of SEM and TEM images, XRD patterns, N2 adsorption–desorption isotherms, Al concentration, TEM-EDS analyses, optical photographs of the used catalysts, thermogravimetric curves, selectivity with TOS, n-hexane uptake kinetics curves, and product distributions with time on stream (<a class="ext-link" href="/doi/suppl/10.1021/acs.iecr.1c01043/suppl_file/ie1c01043_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

engineering, chemical
The Influence of Desilication on High-Silica MFI and Its Catalytic Performance for N2O Decomposition

Qun Shen,Minfang Wu,Hui Wang,Nannan Sun,Chi He,Wei

DOI: https://doi.org/10.1016/j.apsusc.2018.01.052

IF: 6.7

2018-01-01

Applied Surface Science

Abstract:A series of MFI zeolites with different Si/Al ratios were pretreated by a basic solution and their catalytic activity was evaluated in N2O decomposition after iron exchange. The performance of Fe-ZSM-5 catalysts could be improved by alkaline pretreatment. Among these samples, the activity curve of Fe-Z5-250-S sample could move to low temperature by >100 degrees C with a good preservation of hydrothermal stability. It is found that with the meso-microporous hybrid structure, the content of iron as active metal is significantly increased. Additionally, well preservation of the chemical environment around the tetrahedral aluminum and the site accessibility probably may be the other important factors to influence the catalytic activity. (C) 2018 Published by Elsevier B.V.
ZnO Supported on Silicalite-1 As an Efficient Catalyst for Isobutane Dehydrogenation to Isobutene Assisted by CO2

Yajun Luo,Changxi Miao,Yinghong Yue,Weiming Hua,Zi Gao

DOI: https://doi.org/10.1016/j.micromeso.2019.109864

IF: 5.876

2019-01-01

Microporous and Mesoporous Materials

Abstract:The ZnO catalysts supported on Silicalite-1 zeolite with a Zn content between 1% and 9% were synthesized by an incipient wetness method. These catalysts were characterized by XRD, N2 adsorption, SEM, TEM-EDX, UV–vis, DRIFTS and NH3-TPD. They were found to be effective for isobutane dehydrogenation to isobutene assisted by CO2, and the catalytic activity is well correlated with the amount of acid sites which are primarily originated from the dispersed zinc oxide species. Silicalite-1-supported ZnO is far more active than SBA-15-supported one with the same Zn content. The catalytic stability is improved remarkably by introducing CO2 to the feed gas.
Active Fe Species of Fe2o3/Fe-Silicalite-1 Nanowires in N2o Decomposition

Pengfei Xie,Zhen Ma,Tao Meng,Chengyun Huang,Changxi Miao,Yinghong Yue,Weiming Hua,Zi Gao

DOI: https://doi.org/10.1016/j.molcata.2015.08.010

2015-01-01

Abstract:Recently, we reported the hydrothermal conversion of Fe2O3/SiO2 spheres (Fe2O3 nanoparticles supported on SiO2 spheres) into Fe2O3/Fe-Silicalite-1 nanowires in the presence of ethylenediamine and triethylamine (Micropor. Mesopor. Mater. 200 (2014) 52–60). The catalytic performance of Fe2O3/Fe-Silicalite-1 nanowires in CO oxidation, N2O decomposition, and catalytic reduction of NO by NH3 was evaluated. However, the nature of active Fe species of Fe2O3/Fe-Silicalite-1 nanowires in N2O decomposition was not clear. In the current work, additional samples (i.e., Fe-Silicalite-1, Fe2O3/Silicalite-1, and Fe2O3/Fe-Silicalite-1) were prepared by using conventional Silicalite-1 as a precursor, and tested in N2O decomposition. Fe2O3/Silicalite-1 and Fe2O3/Fe-Silicalite-1 prepared by impregnation showed higher activities than Fe-Silicalite-1 prepared by isomorphous substitution, and Fe2O3/Fe-Silicalite-1 nanowires showed the highest activity among these samples. Through relevant characterization employing XRD, XRF, N2 adsorption, TEM, UV–vis, and 57Fe Mössbauer spectroscopy, we conclude that small Fe2O3 nanoparticles with size of 1–2nm are the main active Fe species for N2O decomposition, whereas framework Fe3+ and larger Fe2O3 particles are not so active.
Efficient Co2 Catalytic Hydrogenation over Cuox-Zno/ Silicalite-1 with Stable Cu+ Species

Xiaohui Liu,Baorun Ma,Hongxin Pan,Fan Yang,Guo Yong,Yanqin wang

DOI: https://doi.org/10.2139/ssrn.4105659

2022-01-01

SSRN Electronic Journal

Abstract:Cu-based/SiO2 nanocatalysts with Cu0 or Cu+ species as active sites have been widely investigated for CO2 hydrogenation. Here, 10CuO/silicalite-1(S-1) and 10CuO-2ZnO/S-1 catalysts were cheap prepared by wet impregnation. 7.5% conversion of CO2 can be reached and kept for 100 h over 10CuO-2ZnO/S-1 at 250°C and 3MPa. XPS and in-situ CO-DRIFT show that only Cu+ species exists on both catalysts surface due to silanol nests from S-1. Moreover, there is a synergism between Cu+ species and ZnO on 10CuO-2ZnO/S-1 confirmed by H2 -TPR and in-situ H-D exchange DRIFT, in which ZnO is responsible for H2 dissociation and the Cu+ species of ZnO-Cu2O interface adsorbs CO2. Subsequently, the adsorbed CO2 is hydrogenated to CO via the carboxylate pathway by H species generated from ZnO. This work provides a new insight into the Cu-based/SiO2 , which ZnO-Cu2O interface and silanol nests from S-1 play the key role for CO2 hydrogenation efficiently and steadily.
Catalytic Decomposition of N2O over Fe-ZSM-11 Catalysts Prepared by Different Methods: Nature of Active Fe Species

Pengfei Xie,Yajun Luo,Zhen Ma,Chengyun Huang,Changxi Miao,Yinghong Yue,Weiming Hua,Zi Gao

DOI: https://doi.org/10.1016/j.jcat.2015.07.010

IF: 7.3

2015-01-01

Journal of Catalysis

Abstract:A series of Fe-ZSM-11 catalysts were prepared by different methods and tested in N2O decomposition. First, Fe-ZSM-11 catalysts with different Si/Al ratios (15, 25, 36) were prepared by wet ion exchange. The Fe content and catalytic activity were highest for the catalyst with Si/AI ratio 15. Additional Fe-ZSM-11 catalysts with higher Fe contents were prepared by semicontinuous ion exchange or by using alkaline-treated ZSM-11 as the precursor for wet ion exchange. While the catalyst prepared by semicontinuous ion exchange showed low activity, the catalyst prepared using alkaline-treated ZSM-11 turned out to be the most active in this study. Relevant characterization was conducted using X-ray diffraction, X-ray fluorescence, inductively coupled plasma, N-2 adsorption-desorption, scanning electron microscopy, transmission electron microscopy, ultraviolet-visible spectroscopy, Fe-57 Mossbauer spectroscopy, magnetization tests, and X-ray photoelectron spectroscopy. Our data indicate that small FeOx nanopartides and large iron oxide particles are the predominant Fe species, and small FeOx nanoparticles with low nuclearity are the active Fe species. (C) 2015 Elsevier Inc. All rights reserved.
Silicalite-1 Derivational Desilication-Recrystallization to Prepare Hollow Nano-ZSM-5 and Highly Mesoporous Micro-ZSM-5 Catalyst for Methanol to Hydrocarbons

Zhe Ma,Tingjun Fu,Yujie Wang,Juan Shao,Qan Ma,Chunmei Zhang,Liping Cui,Zhong Li

DOI: https://doi.org/10.1021/acs.iecr.8b03858

2019-01-01

Industrial & Engineering Chemistry Research

Abstract:Mesoporous ZSM-S zeolites were directly synthesized by desilication-recrystallization of silicalite-1 with NaAlO2 as Al source and TPAOH as template. The fabrication mechanism of mesopores was studied based on the different crystal size of silicalite-1 and liquid-to-solid ratio. This revealed that TPA(+) played a protective role in the controllable desilication while Na+ induced the production of mesopores during the recrystallization. When silicalite-1 with a crystal size of 200 nm was treated in a liquid-to-solid ratio of 10 mL/g, hollow structured nano-ZSM-5 with many mesopores (similar to 23 nm) in the shell was produced and its external surface area reached 121 m(2) g(-1). In comparison, homogeneous mesopores (similar to 15 nm) were introduced into the bulk of micro-ZSM-5 under a higher liquid-to-solid ratio of 30 mL/g, providing a maximal external surface area of 171 m(2) g(-1). The catalytic lifetime reached 192 h in methanol to hydrocarbons reaction at a weight hourly space velocity of 4.7 h(-1), four times greater than that of the micro-ZSM-5 synthesized via the traditional hydrothermal synthesis.
Efficient and Stable Ni/ZSM-5@MCM-41 Catalyst for CO 2 Methanation

Chao Miao,Kaixuan Shang,Lixing Liang,Shumei Chen,Jing Ouyang

DOI: https://doi.org/10.1021/acssuschemeng.2c03693

IF: 8.4

2022-09-14

ACS Sustainable Chemistry & Engineering

Abstract:In this work, a Ni-based catalyst supported on a core–shell structure catalytic carrier material (Ni/ZSM-5@MCM-41) based on kaolinite tailings is reported, which exhibits excellent CO2 methanation performance at atmospheric pressure. At 400 °C, CO2 conversion and CH4 selectivity reach 80 and 97% with the space velocity of 12,000 mL gcat –1 h–1, respectively, and it can maintain good stability during the 80 h stability test. Compared with traditional Ni/ZSM-5 and Ni/MCM-41 catalysts, Ni/ZSM-5@MCM-41 has more substantial confinement effects on the active components, and the active components are more evenly dispersed on surface of the carrier. In addition, it is confirmed by the in situ diffuse reflectance infrared Fourier transform spectroscopy technique that CO2 methanation over the Ni/ZSM-5@MCM-41 catalyst follows the path of formate and CO as intermediates.

chemistry, multidisciplinary,engineering, chemical,green & sustainable science & technology
Atomic-scale insights into zeolite-based catalysis in N2O decomposition

Guangzhi He,Bo Zhang,Hong He,Xueyan Chen,Yulong Shan

DOI: https://doi.org/10.1016/j.scitotenv.2019.03.481

2019-07-10

Abstract:Nitrous oxide (N2O) has been the most serious ozone-depleting species throughout the 21st century. Zeolite-based catalysis is a highly promising method for N2O removal in large-scale industrial applications. However, the exchanged transition metal species in zeolites greatly influence the performance of catalysts. The primary factor governing the catalytic activity is a fiercely debated topic and remains highly uncertain. Here we synthesize a series of transition-metal ion (Fe, Co, Ni, Cu)-exchanged ZSM-5 zeolite catalysts. Both experiments and density functional theory (DFT) calculations demonstrate that the activity for N2O decomposition follows the order Fe ≈ Co > Ni > Cu. Analysis of the electronic structure properties reveals that the catalytic activity of the transition-metal ion-exchanged ZSM-5 zeolites is governed by the local softness of active sites and the composition of their HOMOs. The higher the local softness and the proportion of 4s orbitals in the HOMO, the higher the catalytic activity, which facilitates electron transfer in the redox process and thereby reduces the reaction barriers for N2O decomposition into N2 and O2. Clarification of the nature of catalytic activity advances the understanding of the principles of zeolite-based catalysis, and is helpful for the design of highly efficient zeolite catalysts for pollutant removals.
Core–Shell HZSM-5@silicalite-1 Composite: Controllable Synthesis and Catalytic Performance in Alkylation of Toluene with Methanol

Guixian Li,Chao Wu,Peng Dong,Dong Ji,Yongfu Zhang

DOI: https://doi.org/10.1007/s10562-019-03085-y

IF: 2.936

2020-01-09

Catalysis Letters

Abstract:HZSM-5@silicalite-1 catalysts were prepared by the hydrothermal method, and the structure, morphology, acidity and pore texture of core–shell catalysts were studied by XRD, SEM, TEM, NH3-TPD, Py-IR and N2 adsorption/desorption isotherms in detail. Their catalytic performances were tested in the alkylation reaction of toluene with methanol. The results showed that a coating layer was formed in the form of silicalite-1 on HZSM-5. NH3-TPD measurements indicated that HZSM-5@silicalite-1 contained less strong acid sites but more weak acid sites than the parent HZSM-5. The selectivity of p-xylene for toluene alkylation was approximately linear with the percentage of weak acid in total acid. Under the optimal reaction conditions, the conversion of toluene was 34.15%, and the selectivity of p-xylene was 96.77%.

chemistry, physical
An Fe–Mn–Cu/SiO2@silicalite-1 Catalyst for CO Hydrogenation: the Role of the Zeolite Shell on Light-Olefin Production

Weilin Song,Bin Zhang,Lifeng Chen,Jing Shi,Xiaowei Cheng,Lianghua Wu,Weimin Yang,Jian Zhou,Yahong Zhang,Yuewu Tao,Yi Tang

DOI: https://doi.org/10.1039/c5cy01144b

IF: 6.177

2016-01-01

Catalysis Science & Technology

Abstract:The silicalite-1 coated catalyst presents a unique temperature-dependent performance due to the zeolite shell’s diffusion limitation on reactants and products and suppression of secondary reactions on downstream catalysts.

Silicalite-1@Cu-ZSM-5 core-shell catalyst for N2O decomposition

Catalytic Decomposition of N2O over Cu-ZSM-11 Catalysts

Regulating the Microenvironments and the D-Band Center of Hierarchical Nimos/Ts-1 Catalyst by Zro2 to Enhance the Hydrodesulfurization Performance of Dibenzothiophene

CoZSM-11 Catalysts for N2O Decomposition: Effect of Preparation Methods and Nature of Active Sites

Catalytic Decomposition of N2o over Cu-Zsm-5 Nanosheets

Effect of copper precursors on the catalytic performance of Cu-ZSM-5 catalysts in N2O decomposition

Sustainable Synthesis of Core-shell Structured ZSM-5@Silicalite-1 Zeolite

Optimization of Conditions for Preparation of ZSM-5@silicalite-1 Core–shell Catalysts Via Hydrothermal Synthesis

Decomposition of nitrous oxide over Co-zeolite catalysts: role of zeolite structure and active site

Synthesis and Characterization of ZSM-5/Silicalite-1 Core-Shell Zeolite with a Fluoride-Containing Hydrothermal System

Promising Strategy to Synthesize ZSM-5@Silicalite-1 with Superior Catalytic Performance for Catalytic Cracking Reactions

The Influence of Desilication on High-Silica MFI and Its Catalytic Performance for N2O Decomposition

ZnO Supported on Silicalite-1 As an Efficient Catalyst for Isobutane Dehydrogenation to Isobutene Assisted by CO2

Active Fe Species of Fe2o3/Fe-Silicalite-1 Nanowires in N2o Decomposition

Efficient Co2 Catalytic Hydrogenation over Cuox-Zno/ Silicalite-1 with Stable Cu+ Species

Catalytic Decomposition of N2O over Fe-ZSM-11 Catalysts Prepared by Different Methods: Nature of Active Fe Species

Silicalite-1 Derivational Desilication-Recrystallization to Prepare Hollow Nano-ZSM-5 and Highly Mesoporous Micro-ZSM-5 Catalyst for Methanol to Hydrocarbons

Efficient and Stable Ni/ZSM-5@MCM-41 Catalyst for CO 2 Methanation

Atomic-scale insights into zeolite-based catalysis in N2O decomposition

Core–Shell HZSM-5@silicalite-1 Composite: Controllable Synthesis and Catalytic Performance in Alkylation of Toluene with Methanol

An Fe–Mn–Cu/SiO2@silicalite-1 Catalyst for CO Hydrogenation: the Role of the Zeolite Shell on Light-Olefin Production