Abstract:The passive safety commercial pressurized water reactors (PWRs), AP1000 and CAP1400 are equipped with the automatic depressurization system (ADS). The fourth stage of ADS (ADS-4) has the largest discharging capacity among the all ADS stages. During a small break loss-of-coolant accident (SBLOCA), only when the system is fully depressurized by the ADS-4 to near the containment atmospheric pressure, the in-containment refueling water storage tank (IRWST) can deliver the large coolant inventory for the long-term core cooling by its water head. Before the IRWST injection, the core reaches its minimum inventory. So the transition from the ADS-4 depressurization to the IRWST injection is a very challenging period in a SBLOCA. Therefore, to evaluate the passive system performance by the integral effect test (IET), the transition must be simulated properly. This work conducted the scaling analysis for the ADS-4 depressurization and the IRWST injection for designing the related components of the ACME IET facility. A uniform scaling law based on the existing T-branch liquid entrainment models was proposed. For scaling the onset of the IRWST injection, the requirement for reproducing the synergetic effect in an IET was introduced in order to preserve the important event/process occurrence time with the proper conditions, and the scaling laws for the full pressure IRWST injection were obtained. For investigating the transition thermal hydraulic behaviors and the ADS-4 configuration influences on the core safety, one cold leg break test and three double-ended direct-vessel-injection (DEDVI) line break tests with the different ADS-4 failure modes were selected from the ACME SBLOCA test matrix, and the main test data related to the core safety were analyzed and compared. It was found that the ADS-4 actuation significantly accelerated the system depressurization but worsened the core inventory depletion at the same time. In addition, the break condition and the ADS-4 failure mode could differently affect the system depressurization and the core level. The ACC injection during the ADS-4 depressurization in DEDVI was critical for the core level makeup. The insufficient ADS-4 venting capacity delayed IRWST injection, but also mitigated the core inventory depletion. It suggests the ADS-4 design can be potentially optimized in the passive safety system design. (C) 2019 Elsevier Ltd. All rights reserved.

Experimental Investigation of Liquid Entrainment in AP1000 ADS-4 Branch Line with Air–water

Development and Applicability Analyses of ADS-4 Entrainment Model in Large Advanced PWR

Validation of RELAP5 MOD3.3 Code for Entrainment Phenomenon Against FATE Test Facility

Experimental study and theoretical development of liquid entrainment in T-junction with double inlets and single inlet of gas phase

Scaling and Integral Effect Test on Transition from Depressurization to Long-Term Gravity Injection

Experimental Investigation of ADS-4 Entrainment with Air and Boric Acid

The SCDAP/RELAP5 3.2 model of AP1000 on SBLOCA

Experimental Investigation of Pool Entrainment in High Gas Flux Region

Sensitivity Analysis of Stratification Entrainment Model of SCDAP/Relap5 3.2 Code

An Experimental Study of Pool Entrainment with Side Exit

ADS-IRWST Transient Evaluation Model for AP1000 SBLOCA Analysis

Numerical Simulation of AP1000 LBLOCA with SCDAP/RELAP 4.0 Code

The Ap1000 Lbloca Analysis Using Scdap/Relap5

Experimental investigations on the two-phase water entrainment phenomenon at inclined branch T-junctions and numerical simulations based on neptune_cfd

Analysis of the Accelerator-Driven System Fuel Assembly during the Steam Generator Tube Rupture Accident

THE CMT SIMULATION ON THE LARGE IMPASSIVE PWR WITH RELAP 5

Analytical Studies of Long-Term IRWST Injection Core Cooling under Small Break LOCA in Passive Safety PWR

Scaling Analysis of the Pressurizer Surge Line in Nuclear Plant Integral Test Facilities

Applicability of RANS models and pressure drop in edge subchannels for 19-pin wire-wrapped fuel bundle channel in CiADS

Analysis of AP1000 Containment Passive Cooling System During a Loss-of-coolant Accident

RELAP5 Validation for Core Makeup Tank Analysis Based on Separate Effect Tests