Abstract:Fuel electrode-supported solid oxide cells (FE-SOC) offer the possibility of low operation temperatures and / or high power density through the incorporation of a thin, supported electrolyte between two highly active electrodes. However, integrating fuel electrodes with an ionic conductor that is different from that of the electrolyte into FE-SOC remains a challenge due to the interdiffusion phenomena during co-sintering of the half-cell. As a result, most FE-SOC use cermet fuel electrodes made from Ni and stabilized zirconia. Here, we present a FE-SOC based on a Ni-Gd0.1Ce0.9O2- d (GDC) fuel electrode, a three-layer GDC / zirconia / GDC electrolyte and an La0.58Sr0.4CoO3- d (LSC) air electrode. The electrolyte is fabricated by co-sintering a thin, screen-printed layer of GDC with the fuel electrode and support. Subsequent electrolyte layers are deposited via physical vapor deposition (PVD), and the air electrode is fabricated via screen printing. The total electrolyte thickness is less than 5 µm, enabling an area-specific ohmic resistance < 10 mΩ cm² at 700 °C. A current density of 1.6 Acm-² is achieved at a cell voltage of 800 mV and a temperature of 700 °C, using 10% H2O/H2 as fuel and air as oxidant. This performance is about twice as high as that of a conventional Jülich cell using Ni-YSZ and LSCF electrodes and a 10 µm YSZ electrolyte under similar conditions. An electrolysis current of 2 A cm-² was achieved at a cell voltage of 1.11 V, at a temperature of 800 °C and using 50% H2O/H2 and air. The conventional Jülich cell requires a cell voltage above 1.25 V under similar conditions. Under these conditions, the new cell achieves a cell efficiency of 84 %, compared to 73 % for the conventional cell. However, running high electrolysis currents at temperatures below 750 °C resulted in catastrophic cell failure, visible as large voltage jumps in the I-V curve. In addition, a decreasing OCV value with decreasing temperature indicated damage to the cell before the catastrophic failure. Post-test analysis found a large number of cracks in the electrolyte, nucleating at the fuel electrode / electrolyte interface and running toward the air electrode. We show that the likely cause for this failure is the electrochemical reduction and subsequent chemical expansion of the doped ceria electrolyte layer, necessitating a detailed study of the local mechanical stresses in the cell during operation.

Advanced Electrolyte-Free Fuel Cells Based on Functional Nanocomposites of a Single Porous Component: Analysis, Modeling and Validation

A New Energy Conversion Technology Based on Nano-Redox and Nano-Device Processes

A Fuel Cell with a Single Component Functioning Simultaneously As the Electrodes and Electrolyte

Progress in Electrolyte-Free Fuel Cells

Study on the key materials for realizing electrolyte-free fuel cell and semiconductor-ionic membrane fuel cell

Functional Semiconductor–ionic Composite GDC–KZnAl/LiNiCuZnOx for Single-Component Fuel Cell

A Single-Component Fuel Cell Reactor

Development of Novel Single Fuel Cell Based on Composite Polar Plates for Highly Efficient Power Generation

Electro-Chemo-Mechanical Failure in a High-Performance Solid Oxide Cell

A High-performance Fuel Electrode-supported Tubular Protonic Ceramic Electrochemical Cell

Performance of fuel cells with proton-conducting ceria-based composite electrolyte and nickel-based electrodes

From Fundamental Interfacial Reaction Kinetics to Macroscopic Current–Voltage Characteristics: Case Study of Solid Acid Fuel Cell Limitations and Possibilities

Intermediate temperature fuel cell with a doped ceria–carbonate composite electrolyte

Highly Active and Durable Metal‐Free Carbon Catalysts for Anion‐Exchange Membrane Fuel Cells

Fuel Cells Based on Electrolyte and Non-Electrolyte Separators

Enabling high-concentrated fuel operation of fuel cells with microfluidic principles: A feasibility study

Electrokinetic Insights into the Triple Ionic and Electronic Conductivity of a Novel Nanocomposite Functional Material for Protonic Ceramic Fuel Cells

Nanocomposite Electrode Materials for Low Temperature Solid Oxide Fuel Cells Using the Ceria-Carbonate Composite Electrolytes

Nanofiber-Based Oxygen Reduction Electrocatalysts with Improved Mass Transfer Kinetics in a Meso-Porous Structure and Enhanced Reaction Kinetics by Confined Fe and Fe3C Particles for Anion-Exchange Membrane Fuel Cells

A Sodium‐Ion‐Conducting Direct Formate Fuel Cell: Generating Electricity and Producing Base

Ionomer Cross-Linking Immobilization of Catalyst Nanoparticles for High Performance Alkaline Membrane Fuel Cells