Abstract:Magnesium-based alloys show significant promise for widespread applications owing to their lightweight nature and improved mechanical properties achieved through grain refinement via hot rolling. This investigation focuses on Mg-xAl-yCa-zMn (AXM alloys), pre-heated to temperatures of 350, 400, and 450 °C and processed via both single-pass differential speed rolling (DSR) and conventional rolling (CR). The key findings reveal the interplay between processing temperature, strain rate during single-pass rolling, and an innovative approach for incorporating varying amounts of Ca, influencing grain size, quantity of dynamic recrystallization (DRX) grains, and overall mechanical properties, including strength and ductility. A noteworthy observation is the positive correlation between an increase in the total reduction during hot rolling and a higher fraction of DRXed grains. This leads to a significant reduction in average grain size, diminishing from 60.3 ± 54.3 μm to 19.5 ± 14.2 μm at 40%, nearly a third the size of T4 grains (the initial homogenized microstructure of the AXM alloys). The resultant material strength experiences a doubling from an average of 125 ± 10.2 MPa (T4) to 260 ± 25.8 MPa (DSR rolled at 40%) for the AXM alloys with potential improvement in the ductility depending on rolling speed conditions. This study also aims to analyze the combination of rolling temperature, rolling speed, thickness reduction, speed difference and Ca content implemented across a wide range of temperatures and strain rates to provide a holistic approach to the processing parameters affecting the microstructure and mechanical properties of AXM alloys. Furthermore, this study provides a deeper understanding of DRX mechanisms, including continuous DRX (CDRX), discontinuous DRX (DDRX), and twinning induced DRX (TDRX), while each of these mechanisms plays a distinct role in the overall enhancement of formability and performance of magnesium alloys.

Superplasticity in Magnesium Alloys Processed by Different‐Roll‐Speeds Rolling

Influence of Processing Temperature and Strain Rate on the Microstructure and Mechanical Properties of Magnesium Alloys Processed by Single-Pass Differential Speed Rolling

Application of superplasticity in commercial magnesium alloy for fabrication of structural components

On Mechanical Properties and Superplasticity of Mg–15Al–1Zn Alloys Processed by Reciprocating Extrusion

Numerical and Experimental Investigation on Hot Backward Extrusion Process of Mg-Gd-Y-Zn-Zr Magnesium Alloy

Superplastic behavior and microstructural evolution in a commercial Mg-3Al-1Zn magnesium alloy : Superplasticity and its applications

Superplastic Behavior and Microstructural Evolution in a Commercial Mg-3Al-1Zn Magnesium Alloy.

High Strain Rate Quasi-Superplasticity Behavior in an Ultralight Mg-9.55Li-2.92Al-0.027Y-0.026Mn Alloy Fabricated by Multidirectional Forging and Asymmetrical Rolling

High Strain Rate Superplasticity of Rolled AZ91 Magnesium Alloy

Superplasticity and Grain Boundary Sliding in Rolled AZ91 Magnesium Alloy at High Strain Rates

Microstructure Evolution, Constitutive Modelling, and Superplastic Forming of Experimental 6XXX-Type Alloys Processed with Different Thermomechanical Treatments

Dynamic recrystallization, texture and mechanical properties of high Mg content Al–Mg alloy deformed by high strain rate rolling

Superplasticity and microstructure in Mg–Gd–Y–Zr rolled sheet

Superplastic Deformation Mechanisms of Coarse-Grained Rolled Mg-4Y-3RE Magnesium Alloy

A Comparative Study on Superplasticity of Mg-Zn-Y-Zr Processed by Ecae and Hot Rolling

Superplasticity of Mg-5.8Zn-1Y-Zr Alloy Sheet Fabricated by Combination of Extrusion and Hot-Rolling Processes

Mg–3Al–1Zn alloy strips processed by electroplastic differential speed rolling

Obtaining Heterogeneous Microstructure and Enhanced Mechanical Properties in ECAP-Processed AZ61 Alloys via Single-Pass Rolling with Increased Rolling Reduction

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

Thermomechanical Processing and Superplasticity of AZ91 Magnesium Alloy

Microstructure and Microhardness Evolution of Mg-8Al-1Zn Magnesium Alloy Processed by Differential Speed Rolling at Elevated Temperatures