A Selective Chemical Etching Method for Fabrication of Single Mode Fiber Probes

Bo Gong,Tielin Shi,Wei Zhu,Xiaoping Li,Zirong Tang

DOI: https://doi.org/10.1364/iont.2012.ith4a.07

2012-01-01

Abstract:We propose a procedure to fabricate single mode fiber probes, which is grounded through selective chemical etchants. The probes have a double tapered structure with the tapered angle of 30° and 43° respectively.

What problem does this paper attempt to address?

A Method to Control the Fabrication of Etched Optical Fiber Probes with Nanometric Tips

Miaomiao Tao,Yonglong Jin,Ning Gu,Lan Huang

DOI: https://doi.org/10.1088/2040-8978/12/1/015503

IF: 2.1

2009-01-01

Journal of Optics

Abstract:Optical fiber probes with small size tips have attracted much interest in the areas of biosensor and near-field scanning optical microscopy. Chemical etching is a common useful method to fabricate such probes. But it is difficult to study or determine the etching time and control the shape of the fiber during the etching. In this work, a new method combining a fiber optic spectrometer with static chemical etching has been developed to fabricate optical fiber probe nanotips, where the fiber optic spectrometer is used to measure the optical signal during the etching. By calculating and analyzing the testing data, the relationship between the apex angle and the optical signal can be obtained. Accordingly, the process of fabricating optical fibers based on the optical signal can be controlled.
Fabrication of High‐quality SNOM Probes by Pre‐treating the Fibres Before Chemical Etching

Jing Yang,Jiasen Zhang,Zhi Li,Qihuang Gong

DOI: https://doi.org/10.1111/j.1365-2818.2007.01821.x

IF: 1.9522

2007-01-01

Journal of Microscopy

Abstract:Summary A new method to fabricate high‐quality fibre probes for scanning near‐field optical microscopes by pre‐treating the fibre before chemical etching was proposed and implemented. In the pre‐treating process, the diameter of the fibre is reduced to a range of 7 –20 μm by etching one end of the fibre in the HF solution and a taper angle is formed simultaneously. Then the tapered part of the fibre is coated with a thick layer of plastic film and etched in the HF solution again. High‐quality probes are obtained with an apex diameter as low as ∼20 nm and a large cone angle.
Selective Electroless Silver Plating of Optical Fiber Probes with Protruding Tips

Miaomiao Tao,Aihong Wang,Lina Xu,YongLong Jin,Min Cao,Ning Gu

DOI: https://doi.org/10.1007/s00542-015-2682-5

2015-01-01

Microsystem Technologies

Abstract:A new simple method, selective electroless silver plating, has been developed for fabricating optical fiber probes with protruding tips. The key of the method is the surface treatments of the tapered optical fiber. Surface treatments contain following steps: self-assembly of MPTS, masked UV exposure and catalyst adsorption. By these treatments, selective active binding site of silver is formed in the tapered optical fiber.
The Art of Electrochemical Etching for Preparing Tungsten Probes with Controllable Tip Profile and Characteristic Parameters

Bing-Feng Ju,Yuan-Liu Chen,Yaozheng Ge

DOI: https://doi.org/10.1063/1.3529880

2011-01-01

Abstract:Using custom made experimental apparatus, the art of electrochemical etching was systematically studied for fabricating micro/nano tungsten probes with controllable tip profiles of exponential, conical, multidiameter, and calabashlike shapes. The characteristic parameters of probe including length, aspect ratio, and tip apex radius could also be well defined. By combining of static and dynamic etching, the conical-shape probe with length up to several millimeters, controllable tip apex radius, and cone angle could be fabricated. In addition, by continuously lifting the tungsten wire up during the electrochemical etching with different speeds and distances, the multidiameter shape probe could be fabricated. Finally by controlling the anodic flow, the multiple “neck-in” could be realized creating a calabashlike probe. The aspect ratio of probes depends on (i) the effective contact time between the surrounding electrolyte and the wire, (ii) the neck-in position of immersed tungsten wire. Under the optimized etching parameters, tungsten probes with a controllable aspect ratio from 20:1 to 450:1, apex radius less than 20 nm, and cone angle smaller than 3° could be achieved. The technique is well suited for the tungsten probe fabrication with a stabilized stylus contour, ultra-sharp apex radius, and high production reproducibility. The art for preparing microprobes will facilitate the application of such microprobes in diverse fields such as dip-pen nanolithography, scanning probe microscopy, micromachining, and biological cellular studies.
Fabrication and Characterization of Fiber-Optic Nano-Probes with High Transmission Efficiency and High Resolution

Xiumei Liu,Jia Wang,Dacheng Li

DOI: https://doi.org/10.3321/j.issn:0253-2239.2000.05.015

2000-01-01

Abstract:Two probe models were presented, which satisfy the conditions of high optical resolution together with high transmission efficiency. An optical fiber probe with the transitional taper in hyperbolic or parabolic shape was produced by heating-pulling method followed by a rapid chemical etching in 40% buffered hydrofluoric acid to sharpen the tips, keeping the shape and conic angle unchanged. To demonstrate the high transmission efficiency of tip, the spot distribution was compared with that of conventional taffy-pulled probe. The evanescent wave decay curve and the scanning near-field image of holographic grating were given. An approach curve of shear force was shown to verify its applicability to tip-sample distance regulation.
A Simple Approach to Fiber-Based Tunable Microcavity with High Coupling Efficiency

Peng Qing,Jue Gong,Xing Lin,Ni Yao,Weidong Shen,Arash Rahimi-Iman,Wei Fang,Limin Tong

DOI: https://doi.org/10.1063/1.5083011

IF: 4

2019-01-01

Applied Physics Letters

Abstract:We report a simple technique for the realization of fiber-based Fabry-Pérot microcavities with large Q/V values as well as high cavity-to-fiber coupling efficiencies. The open microcavity we demonstrate consists of a flat mirror and a concave mirror on the tip of a single mode optical fiber. Combining hydrofluoric acid chemical wet etching with CO2 laser reflow, we obtain a fiber-tip atomically smooth concave surface with a diameter of 4.7 μm determined by the fiber core size. The concave surface with a spherical profile is automatically aligned with the fiber core, which enables high cavity-to-fiber power coupling efficiency (higher than 90%) with an optimal fiber-tip mirror's radius of curvature based on numerical simulation results. After distributed-Bragg-reflector coating, we have realized a wavelength-tunable open microcavity with a quality factor Q exceeding 1000 and a mode volume V of 13.6 μm3, and laser emission is demonstrated from this microcavity.
Fabrication of Large Cone Angle Optical Fiber Probe by Dynamic Chemical Etching Method

JL Sun,GY Tian,Q Li,J Zhao,JH Guo,AF Xie,ZB Zhang

DOI: https://doi.org/10.7498/aps.50.2382

IF: 0.906

2001-01-01

Acta Physica Sinica

Abstract:According to the hydraulic transmission principle, a device for fabricating large cone angle near-field optical fiber probe by means of dynamic chemical etching is developed. The results indicated that in the course of traditional fabrication of optical fiber probes by chemical etching, the configuration and the cone angle of the taper can be controlled efficiently through controlling the velocity of the lifting of etching fluid. Furthermore, The advantage of controlling the displacement between optical fiber probe and etching fluid step by step in the fabrication of large cone angle optical fiber probe is also described in this paper. A large cone angle near-field optical fiber probe in scanning near-field optical microscopy is applied to measuring the sphere with a diameter 200nm. Its force images show that this probe has high topography resolution (～50nm).
A reproducible electropolishing technique to customize tungsten SPM probe: From mathematical modeling to realization

Yaozheng Ge,Wei Zhang,Yuan-Liu Chen,Chao Jin,Bing-Feng Ju

DOI: https://doi.org/10.1016/j.jmatprotec.2012.08.004

IF: 6.3

2013-01-01

Journal of Materials Processing Technology

Abstract:The present work is carried out with the aim of developing an optimized electropolishing technique for the process of electrochemical etching from mathematical modeling to the final realization of the well-prepared tungsten SPM probes. Based on the axisymmetric shapes of bounded interfaces, a calculation scheme of successive approximation is derived, which facilitates the numerical solutions for a wide range of parameter values which will cover most practical situations. The proposed art of electrochemical etching technique and process are experimentally confirmed to have advantages for the tungsten probe fabrication of the stabilized stylus contour, ultra-sharp apex radius and high production reproducibility. The tungsten probes with profiles of exponential, conical, and multi-diameter with stabilized stylus contour, and ultra-sharp apex radius are fabricated. The characteristic parameters of the probe including length, aspect ratio and tip apex radius can also be well defined. The reproducible technique opens a way of batch customization of metallic SPM probes with high quality.
Fabrication and Application of Nearfield Optical Fibre Probe

JL Sun,JH Xu,GY Tian,JH Guo,J Zhao,AF Xie,ZB Zhang

DOI: https://doi.org/10.1088/1009-1963/10/7/309

2001-01-01

Chinese Physics

Abstract:In this paper, the fabrication of a large cone angle near-field optical fibre probe, using the two-step chemical etching method and bent probe, is introduced, and the controlling parameters of the coated Cr-Al film at the probe tip are presented. The scanning electron microscopy images display that the tip diameter of the uncoated large cone angle fibre probe obtained is less than 50nm, the cone angle over 90 degrees, and the diameter of light aperture at the coated probe tip is less than 100nm. The measured results of the optical transmission efficiency for various probe tips show that the uncoated straight optical fibre probe, film-coated straight probe and film-coated bent probe are 3x10(-1), 2x10(-3), and 1x10(-4) times that of the hat fibre probe, respectively. In addition, the force images and near-field optical images of a standard sample are acquired using a large cone angle and film-coated bent probe.
Fabrication And Characterization Of Near-Field Optical Fiber Nanoprobes With High Resolution And High Transmission Efficiency

Xiumei Liu,Jia Wang,Dacheng Li

DOI: https://doi.org/10.1117/12.401677

2000-01-01

Abstract:As one of the key components in scanning near-field optical microscopes (SNOM), optical fiber probes can be fabricated by use of either laser-heated pulling or chemical etching. For high-resolution near-field imagine, the nearfield optical signal is rapidly attenuated as the aperture of probes decreases. It is thus important to fabricate probes optimized for aperture size and optical transmission. We present a two step fabrication method of 50%similar to 70% reproducibility to obtain probes with high optical transmission efficiency as well as small tip diameters. First, optic fiber probes with the transitional taper in hyperbolic or parabolic shape are produced by use of the simple home-made device for heating-pulling. Then, a rapid chemical etching with 40% buffered hydrofluoric acid is used to sharpen the tip while keeping the taper shape and the conic angle unchanged. The method renders us to achieve probes with tip diameters in the range of 20nm similar to 200nm and the tape angle near the tip apex in the range of 20 degrees similar to 60 degrees. Particularly, the length of the non-propagating evanescent wave modes region decreases greatly to tens of micrometers or even less. In order to test the achieved probes, we give the photon tunneling decay curve and scanning near-field optical image of holographic grating by use of PSTM mode and collection-mode SNOM, respectively. In addition, an approach curve of shear force with hyperbolic probe is shown to verify its applicability to sample-tip distance regulation on basis of the principle of shear-force.
An Multi-to-single Mode Conversion Experiment Using the Tapered Fiber

CHENG Bo-tao,YUAN Bo-jiang,CHEN He,ZHAO Cheng-liang,LU Xuan-hui

DOI: https://doi.org/10.3969/j.issn.1005-5630.2006.03.007

2006-01-01

Abstract:The guiding modes of a single mode fiber(@1550nm),when the cutoff frequency of the fiber is less than the frequency of the launching field,have been investigated.The fused tapered fiber has been fabricated by using the flame of a spirit lamp.If controlling the fiber dimension well during pulling process,the unique tapered fiber will have a multimode input end and a single mode output end for launching wavelength 632.8nm,which are demonstrated in our experiment.
Study on Large Cone Optical Fiber Probes by Dynamic Chemical Etching Based on Siphon Principle

Zhihua Ding

2006-01-01

Abstract:Based on siphon principle and dynamic large cone chemical etching method,link them together organically to fabricate the optical fiber probes.The optical fiber probes with ideal light transmission efficiency and high resolution can be easily obtained by the method.Probes with apex diameter from 80nm to 300nm and taper angle from 32°to 45° are be easily achieved.By the SPSS software,the distinct difference can be analyzed between the dynamic chemical etching based on the siphon principle and the traditional chemical etching method.
Effect of Etchant Diffusion on Tip Profiles of Glass Fiber Probes.

YH Wang,ZY Yu,YB Tan,N Gu,KD Wesche

DOI: https://doi.org/10.1166/jnn.2006.177

2006-01-01

Journal of Nanoscience and Nanotechnology

Abstract:The tips of the probes are the key components in scanning probe microscopes and their applications in nano-scale imaging and nanofabrications. We investigated first the change of near-field scanning optical microscopy probe tips from optical fiber against time by chemical static etching. Several coverlayer-hydrofluoric acid aqueous solution systems and their possible factors affecting the tips' profile were studied. Tips with shorter tapers, larger conical aperture angles, and reproducible shapes were successfully obtained in high yields. It was found that the taper profiles were affected to a great extent by the one-dimensional linear diffusion of etchants in the coverlayer caused by concentration gradients and convection.
Controllable fabrication of fiber nano-tips by dynamic chemical etching based on siphon principle

Ning Gu,Chang-an Li,Long Sun,Zhan-hui Liu,Yong-kang Sun,Li-na Xu

DOI: https://doi.org/10.1116/1.1781185

2004-01-01

Abstract:A dynamic chemical etching method based on siphon principle has been developed for controllable fabrication of fiber nano-tips, which could be used in near-field optical microscope and optical nanosensors. Compared with traditional static chemical etching, this method has advantages such as reproducibility, controllability, convenience, less cost, and making tip surface smooth. The overall shape and the tape angle of the tip can be effectively controlled through the speed and direction of water flux. Tips with taper angles from 20degrees to 55degrees, and tips with double tapers have been achieved by this method. (C) 2004 American Vacuum Society.
Fabrication Methods and High-Precision Diameter Control Techniques of Optical Micro-/Nanofibers

Kang Yi,Liu KeYing,Xie Yu,Gong Jue,Yao Ni,Fang Wei,Guo Xin,Zhang Lei,Wang Pan,Tong LiMin

DOI: https://doi.org/10.1360/sspma-2020-0027

2020-01-01

Abstract:Owing to their favorable properties including small sizes, tight optical confinement, large fractional evanescent fields, and low waveguiding losses, optical micro-/nanofibers have attracted broad research interest and technological applications in recent years, in which the precision in micro-/nanofiber fabrication is critical to determine their waveguiding properties and performances. Here, we firstly introduce the principles of high-temperature taper drawing of glass fibers. Next, we review typical fabrication methods including flame-heated manual drawing approach, flame-heated mechanical drawing technique, electric-heated mechanical drawing technique and laser-heated mechanical drawing technique. Cons and pros of the above-mentioned techniques are discussed, followed by a brief introduction to the fabrication of polymer micro-/nanofibers. Thirdly, we introduce the principle and techniques of high-precision diameter control in glass micro-/nanofiber fabrication based on a in-situ feedback from the cutoff of high-order waveguiding modes, which can offer a diameter precision down to nanometer level. In addition, several techniques for diameter measurement of a micro-/nanofiber are also introduced. Finally, we end the review with a brief summary in micro-/ nanofiber fabrication, as well as an outlook to future possibilities.
Systematic Study of Electropolishing Technique for Improving the Quality and Production Reproducibility of Tungsten STM Probe

Bing-Feng Ju,Yuan-Liu Chen,Mingming Fu,Yu Chen,Yunhai Yang

DOI: https://doi.org/10.1016/j.sna.2009.08.013

2009-01-01

Abstract:Based on the systematic study of electropolishing process, an improved tungsten STM probe fabrication technique has been presented. The proper combination of pulse current and the electrolyte concentration is explored for the elimination of impurities and achieves high quality probes with ultra-smooth surfaces. An optimized immersion depth of tungsten wire in electrolyte is proposed for the purpose of realizing the probe with sharp apex as well as high aspect ratio structure. A control strategy for determining the power-off instant during the procedure of electropolishing is developed which will facilitate the fabrication of probe with exponential contour as well as ultrasharp tip. The proposed technique and process are experimentally confirmed to have advantages for the STM probe fabrication of the stabilized stylus contour, typically with apex radius of 30nm and the yield rate reaches as high as 85%.
Miniaturized Metal-Dielectric-Hybrid Fiber Tip Grating for Refractive Index Sensing

Jun-Long Kou,Sun-Jie Qiu,Fei Xu,Yan-Qing Lu,Ye Yuan,Gang Zhao

DOI: https://doi.org/10.1109/LPT.2011.2166151

IF: 2.6

2011-01-01

IEEE Photonics Technology Letters

Abstract:We fabricate a miniaturized metal-dielectric-hybrid fiber tip grating (FTG) using a focused ion beam (FIB) method with high accuracy for refractive index sensing applications. It is the smallest fiber grating by now (nearly 10 μm in length located at the fiber tip of 3 μm in radius) and it has strong surface corrugations with notches periodically. The grating shows refractive index sensitive [125 ...
Fabrication of the Tip of GaAs Microwave Probe by Wet Etching

yang ju,hiroyuki sato,hitoshi soyama

DOI: https://doi.org/10.1115/IPACK2005-73140

2005-01-01

Abstract:In order to develop a new structure microwave probe, the fabrication of micro tip on the GaAs wafer surface was studied. The effects of the shape, direction, and size of etching mask to the fabricated tip were discussed in details. By finding the most suitable etching conditions, a tip having 7 mu m high, 1.4 aspect ratio, and 50 nm curvature radius was formed. The experimental result indicates that the tip having the similar capability to sense the surface topography of materials as that of commercial atom force microscope (AFM) probe.
Fabrication and Characterization of Bioprobe with Mid-Infrared Light Channel

Peng Chuandi,Zheng Junzhe,Zhu Xiaosong,Chang Chao,Shi Yiwei

DOI: https://doi.org/10.3788/aos201939.1223004

2019-01-01

Abstract:Herein, a bioprobe based on hollow fibers with electrical and optical delivery channels is proposed to realize low attenuation transmission of mid -infrared light at the wavelength band ranging from 5 m to 10 p.m. Cyclic olefin polymer (COP) is used to isolate the front-end of the probe from water and the necessary sealing technology is designed and optimized. The loss of bioprobe with length of 20 cm and inner diameter/outer diameter (11)/01)) of 0.7 mm/1.5 mm is 1.38 dB at a wavelength of 5.1 p.m. By controlling the sealing process, COP sealed windows with different shapes arc fabricated to modify the output beam. The focal length and far-field divergence angle for these different configurations arc analyzed by measuring the output beam profiles. This approach will provide more ways and means for neuroscience research and biomedical application.
Tapered Photonic Crystal Fiber Interferometer with Enhanced Sensitivity

Sun-jie Qiu,Ye Chen,Jun-long Kou,Fei Xu,Yan-qing Lu

DOI: https://doi.org/10.1117/12.903958

2011-01-01

Abstract:We fabricate a miniature tapered photonic crystal fiber (PCF) interferometer with enhanced sensitivity by a new acid microdroplets etching method. This method, without elongating the PCF, moving and re-fixing the device during etching and measuring refractive index sensitivity, is very simple, cost-efficient and highly stable over time. We investigate the refractive index sensing properties with different PCF diameters both theoretically and experimentally. The size decreases and the sensitivity increases an order of magnitude after etching the PCF. If we can optimize the etching process, we can fabricate more uniformly and thinly tapered PCF interferometer with higher sensitivity (similar to 100 times) theoretically in the future.

A Selective Chemical Etching Method for Fabrication of Single Mode Fiber Probes

A Method to Control the Fabrication of Etched Optical Fiber Probes with Nanometric Tips

Fabrication of High‐quality SNOM Probes by Pre‐treating the Fibres Before Chemical Etching

Selective Electroless Silver Plating of Optical Fiber Probes with Protruding Tips

The Art of Electrochemical Etching for Preparing Tungsten Probes with Controllable Tip Profile and Characteristic Parameters

Fabrication and Characterization of Fiber-Optic Nano-Probes with High Transmission Efficiency and High Resolution

A Simple Approach to Fiber-Based Tunable Microcavity with High Coupling Efficiency

Fabrication of Large Cone Angle Optical Fiber Probe by Dynamic Chemical Etching Method

A reproducible electropolishing technique to customize tungsten SPM probe: From mathematical modeling to realization

Fabrication and Application of Nearfield Optical Fibre Probe

Fabrication And Characterization Of Near-Field Optical Fiber Nanoprobes With High Resolution And High Transmission Efficiency

An Multi-to-single Mode Conversion Experiment Using the Tapered Fiber

Study on Large Cone Optical Fiber Probes by Dynamic Chemical Etching Based on Siphon Principle

Effect of Etchant Diffusion on Tip Profiles of Glass Fiber Probes.

Controllable fabrication of fiber nano-tips by dynamic chemical etching based on siphon principle

Fabrication Methods and High-Precision Diameter Control Techniques of Optical Micro-/Nanofibers

Systematic Study of Electropolishing Technique for Improving the Quality and Production Reproducibility of Tungsten STM Probe

Miniaturized Metal-Dielectric-Hybrid Fiber Tip Grating for Refractive Index Sensing

Fabrication of the Tip of GaAs Microwave Probe by Wet Etching

Fabrication and Characterization of Bioprobe with Mid-Infrared Light Channel

Tapered Photonic Crystal Fiber Interferometer with Enhanced Sensitivity