Erbium-doped fiber laser mode-locked with a few-layer MoS2 saturable absorber

handing xia,heping li,changyong lan,chun li,xiaoxia zhang,shangjian zhang,yong liu

DOI: https://doi.org/10.1364/ACPC.2014.ATh3A.89

2014-01-01

Abstract:We demonstrate an erbium-doped fiber ring laser passively mode-locked by a CVD-grown few-layer MoS 2 saturable absorber. Stable soliton pulses centered at 1570.1 nm with pulse duration of 1.36 ps are achieved.

What problem does this paper attempt to address?

Generation of Trapezoidal Envelope Pulses and Soliton Rains from Passively Mode-Locked Fiber Laser with MoS2 Saturable Absorber on Microfiber

Zhenhong Wang,Ruijing He,Yan-ge Liu,Hao Zhang,Simeng Han,Hongye Li,Guangdou Wang,Guang Yang,Zhi Wang

DOI: https://doi.org/10.7567/apex.11.072504

IF: 2.819

2018-01-01

Applied Physics Express

Abstract:We report the generation of trapezoidal envelope pulses and soliton rains in an erbium-doped fiber laser with an MoS2-deposited microfiber saturable absorber. The pulse duration of the trapezoidal envelope pulses increases from 7 to 95 ns with the increment of the pump power. The maximum intracavity pulse energy is as high as 34 nJ. At a low pump power, the proposed laser can be switched to the soliton-rains regime by properly changing the polarization states. The microfiber-based MoS2 all-fiber laser can serve as an optical source with improved pulse energy for potential applications in nonlinear dynamics. (c) 2018 The Japan Society of Applied Physics.
980-nm Q-switched photonic crystal fiber laser by MoS 2 saturable absorber

Pingxue Li,Boxing Liang,Meng Su,Yuefei Zhang,Yan Zhao,Mengmeng Zhang,Chunmei Ma,Ning Su

DOI: https://doi.org/10.1007/s00340-016-6433-9

2016-01-01

Applied Physics B

Abstract:We demonstrate a 980-nm Q-switch Yb-doped photonic crystal fiber laser by a multilayer molybdenum sulfide polymer composite as the broadband saturable absorber which is prepared by the chemical vapor deposition method. We achieve passively Q-switching operations at 978 nm with the pulse width of 2.7 and 0.63 μs, corresponding to the repetition rate of 212 and 221 kHz, respectively. The maximum output power is 127 mW. It is the first time that MoS 2 Q-switched Yb-doped photonic crystal fiber laser at 980 nm is demonstrated. The experimental results show that few-layer MoS 2 is a promising broadband saturable absorber material.
Stable Nanosecond-Pulse Fiber Lasers Mode-Locked with Molybdenum Diselenide

Hu Liang,Yange Liu,Ruijing He,Hongye Li,Zhi Wang

DOI: https://doi.org/10.1109/lpt.2018.2874429

IF: 2.6

2018-01-01

IEEE Photonics Technology Letters

Abstract:We report on the formation of the nanosecond pulse in an erbium-doped fiber laser mode-locked with a molybdenum diselenide (MoSe2)-deposited microfiber. The evolution of the pulse states from slightly chirped picosecond pulse to highly chirped nanosecond pulse was observed. As the pump power increases to a certain value, the picosecond pulse abruptly transforms into nanosecond pulse with the pulse duration of 70 ns and the maximum pulse energy of 21 nJ at the fundamental repetition rate of 3.54 MHz. With the advantages of high pulse energy, large pulse duration, and low peak power, the nanosecond pulse could be destined for amplification and compression to achieve high-power applications promisingly.
Passively Mode-locked Ytterbium-doped Fiber Laser Based on MoO3 As Saturable Absorber

Jiang Jun-lin,Yue Wen-jie,Wang Wei-qi,Ding Yi-chen,Wu Bo,Shen Yong-hang

DOI: https://doi.org/10.3788/gzxb20184709.0914001

IF: 0.6

2018-01-01

ACTA PHOTONICA SINICA

Abstract:A MoO3 saturable absorber based on Yb-doped mode-locked fiber laser which can operate in both continuous wave and Q-switched mode-locked regimes was reported. A stable continuous wave mode-locked pulse train at a repetition rate of 17 MHz was achieved by using a ring cavity configuration at 95 mW incident pump power, the pulse width, central wavelength and 3 dB spectral bandwidth are 130 ps, 1 067.06 nm and 0.27 nm. Stable Q-switched mode-locked pulse train occurred at 280 mW incident pump power. As the pump power varied from 280 mW to 400 mW, the repetition rate of Q-switched envelope varied from 26.51 to 48.7 kHz, and the width of Q-switched envelope varied from 14.6 mu s to 4.1 mu s, the pulse width and the central wavelength remained invariant. The 3 dB spectral bandwidth was 0.62 nm.
Wideband saturable absorption in few-layer molybdenum diselenide (MoSe2) for Q-switching Yb-, Er- and Tm-doped fiber lasers

R. I. Woodward,R. C. T. Howe,T. H. Runcorn,G. Hu,F. Torrisi,E. J. R. Kelleher,T. Hasan

DOI: https://doi.org/10.1364/OE.23.020051

2015-06-12

Abstract:We fabricate a free-standing molybdenum diselenide (MoSe2) saturable absorber by embedding liquid-phase exfoliated few-layer MoSe2 flakes into a polymer film. The MoSe2-polymer composite is used to Q-switch fiber lasers based on ytterbium (Yb), erbium (Er) and thulium (Tm) gain fiber, producing trains of microsecond-duration pulses with kilohertz repetition rates at 1060 nm, 1566 nm and 1924 nm, respectively. Such operating wavelengths correspond to sub-bandgap saturable absorption in MoSe2, which is explained in the context of edge-states, building upon studies of other semiconducting transition metal dichalcogenide (TMD)-based saturable absorbers. Our work adds few-layer MoSe2 to the growing catalog of TMDs with remarkable optical properties, which offer new opportunities for photonic devices.

Optics
Q-Switched pulse generation with an electro-deposited MoS2 film

Lian Hong Lee,Abdulkadir Mukhtar Mukhtar Diblawe,Ahmad Haziq Aiman Rosol,Zian Cheak Tiu,Hamzah Arof,S.W Wadi Harun

DOI: https://doi.org/10.1088/1402-4896/ad729b

2024-08-25

Physica Scripta

Abstract:We demonstrated a Q-switched erbium-doped fiber laser (EDFL) applying a new saturable absorber based on MoS2 film, which was grown onto ITO substrate through an electro-deposition process. The film was then added to an EDFL resonator to modulate the cavity loss, resulting in a Q-switched laser at 1559.4 nm with a minimum pulse duration of 4.75 μs and a maximum pulse rate of 89.9 kHz. The fundamental frequency signal-to-noise ratio was recorded at 62.28 dB, indicating the stability of the laser. This finding reveals the potential of the needle-like structure of MoS2 as low-cost, practical, and effective saturable absorbers.

physics, multidisciplinary
Picosecond pulse generation in a mono-layer MoS2 mode-locked Ytterbium-doped thin disk laser

Wenkai Li,Y. Leng,Zhengzheng Liu,Jun Lu,X. Zou,Chun Li,Yanqi Liu

DOI: https://doi.org/10.3788/COL201715.041401

2017-02-17

Abstract:A mode-locked (ML) picosecond ytterbium-doped thin disk laser using a monolayer MoS2 as the saturable absorber (SA) is demonstrated. The monolayer MoS2 is fabricated through the method of low-pressure chemical vapor deposition. The laser directly produces stable ML picosecond pulses at a slope efficiency of 9.71%. The maximum output power is approximately 890 mW, while the corresponding repetition, pulse energy, and pulse duration are 48.6 MHz, 18.3 nJ, and 13.1 ps, respectively. Results suggest that the monolayer MoS2 is a promising SA for ultrafast lasers system.

Engineering,Physics,Materials Science
Evolution of Complex Pulse-Bunches in a Bound-State Soliton Fiber Laser

Hu Liang,Zhenhong Wang,Ruijing He,Yange Liu,Hongye Li,Lifa Ni,Zhi Wang

DOI: https://doi.org/10.1109/lpt.2018.2856863

IF: 2.6

2018-01-01

IEEE Photonics Technology Letters

Abstract:The evolution of complex pulse-bunches in a bound-state soliton fiber laser with a MoS2 saturable absorber is observed with increasing pump laser power. The experiment demonstrated that the stable two-soliton bound state with fixed and tight separation was achieved, inducing strong interplay between the two solitons. The fundamental bound-state mode-locking operations were maintained and the pulse train gradually evolved into complex pulse-bunches to balance the accumulated cavity nonlinear effects as the pump power increased. Our results may offer a platform for the commercial development of stable double-pulse laser sources.
171st-order harmonic soliton erbium-doped fiber laser based on 2H-MoTe 2 saturable absorber

Hai-Yan Liu,Ze-Xin Zhang,Lu-Feng Xv,Jin-Rong Tian,Yan-Rong Song

DOI: https://doi.org/10.1088/1612-202x/ad3cbe

IF: 1.704

2024-04-24

Laser Physics Letters

Abstract:We have demonstrated a high order harmonic mode-locked erbium-doped fiber laser by utilizing 2H-MoTe 2 film as a saturable absorber (SA). The SA is synthesized by depositing 2H-MoTe 2 film on a D-shaped fiber. The nonlinear optical properties of the 2H-MoTe 2 SA are characterized, showing a modulation depth of 14.7% and a saturation intensity of 3 GW cm −2 . Through optimizing the pump power and intra-cavity polarization state, a 171st-order harmonic soliton at 0.9 GHz repetition frequency with a pulse width of 1.06 ps was obtained. The fundamentally mode-locked pulse train had a pulse width of 1.03 ps and a repetition rate of 5.33 MHz. To the best of our knowledge, the 171st-order harmonic soliton is the highest operating repetition frequency that has ever been demonstrated in a 2H-MoTe 2 SA mode locked fiber laser. The results indicate the potential of 2H-MoTe 2 SA at high repetition rates regimes, which could benefit for future possible application.

optics,physics, applied
Mos2 Nanoflowers As High Performance Saturable Absorbers for an All-Fiber Passively Q-Switched Erbium-Doped Fiber Laser

Rongfei Wei,Hang Zhang,Xiangling Tian,Tian Qiao,Zhongliang Hu,Zhi Chen,Xin He,Yongze Yu,Jianrong Qiu

DOI: https://doi.org/10.1039/c5nr08457a

IF: 6.7

2016-01-01

Nanoscale

Abstract:Strong saturable absorption was observed in MoS2 nanoflowers, which were synthesized by a facile solvothermal method. A MoS2 nanoflower-based saturable absorber with a high modulation depth of 51.8% and a large saturable intensity of 275.5 GW cm(-2) was introduced to the application of passively Q-switched fiber laser generation. Stable passively Q-switched fiber laser pulses at 1.56 mu m with a low threshold power of 16.10 mW, high signal-to-noise ratio of 52.5 dB and short pulse duration of 1.9 mu s were obtained. More importantly, a high output power of 3.10 mW related to a large pulse energy of about 51.84 nJ can be attained at a very low pump power. The efficiency of the laser reaches 4.71%, which is larger than that of the prepared layered MoS2 and recently reported MoS2-based passively Q-switching operations. Such results imply that the MoS2 nanoflowers are an excellent candidate for a saturable absorber in passively Q-switched fiber lasers at a low pump intensity.
C-band dual-wavelength synchronized mode-locked erbium-doped fiber laser using a common absorber

Zhenrui Li,Nian Lv,Xin Feng,Shi Li,Yiyu Sun,Yu Yin,Pengfei Wang

DOI: https://doi.org/10.1016/j.optcom.2023.129569

IF: 2.4

2023-05-06

Optics Communications

Abstract:We demonstrate a C-band dual-wavelength synchronized mode-locked erbium-doped fiber laser based on a common single-wall carbon nanotube saturable absorber and two loop resonators. The synchronous mode-locked pulses laser is with a repetition rate of 16.28 MHz and durations of 1.95 ps and 1.21 ps at 1533 nm and 1562 nm, respectively. The tolerance of a cavity-length mismatch is about 830μm . The proposed dual-wavelength laser system exhibits a flexibly controlled performance and a long-term stability, which offers great potential for a number of applications, such as difference-frequency terahertz-wave generation and field-enhancement Raman microscopy.

optics
Passively Q-switched and mode-locking fiber laser based on Sb2S3 saturable absorber

Xuehui Yao,Ya Liu,Sijia Liu,Qiang Zhang,Guoqing Hu

DOI: https://doi.org/10.1016/j.yofte.2023.103616

IF: 2.8

2024-01-01

Optical Fiber Technology

Abstract:Stable mode-locking pulses were obtained in an erbium-doped fiber laser (EDFL) by using antimony sulfide (Sb2S3) as saturable absorber (SA). The Sb2S3-SA fabricated with the optical deposition method was connected to a ring cavity of EDFL for Q-switching and mode-locking, respectively. When the configuration of the fiber cavity is compact with a cavity length of 5 m, Q-switched pulses were generated with repetition frequency from 60.6 kHz to 69.9 kHz by tuning the pump power. Moreover, when additional single-mode fiber (SMF) was inserted into the cavity, self-started mode-locking with ps pulses was obtained. For further investigating the performance of the SA in mode-locking, an inline fiber polarizer was inserted into the compact cavity to achieve hybrid mode-locking operation generating pulses with pulse widths of fs and a fundamental frequency of 29.2 MHz with a signal-to-noise ratio (SNR) of 76 dB. The experimental results indicate that the Sb2S3 material has great application prospects in ultrafast optics due to its excellent optical properties.

telecommunications,engineering, electrical & electronic,optics
Broadband saturable absorption responses of few-layered MoSe 2 nanosheets for all-solid-state Q-switched lasers

Lihua Cao,Han Pan,Wenjing Tang,Ying Li,Hongwei Chu,Zhongben Pan,Shengzhi Zhao,Wei Ji,Dechun Li

DOI: https://doi.org/10.1016/j.optmat.2022.113387

IF: 3.754

2022-12-23

Optical Materials

Abstract:Few-layered molybdenum diselenide (MoSe 2 ) nanosheets were successfully fabricated by the ultrasound-assisted liquid phase exfoliation (UALPE) method. It exhibits broadband nonlinear optical (NLO) responses with optical modulation depths of 12.4% and 9.3% at 1.3 and 2 μm, respectively. Based on this, it was transferred onto a quartz substrate, acting as a saturable absorber (SA) to initiate solid-state pulsed lasers. The Q-switched Nd: GdVO 4 laser with a minimum pulse duration of 366 ns and a repetition rate of 196 kHz was generated at around 1.3 μm. Meanwhile, the Q-switched Tm: YLF laser with a minimum pulse duration of 200 ns and a repetition rate of 43 kHz was obtained at around 2 μm. The experimental results indicate that few-layered MoSe 2 nanosheets have a significant development prospect as a SA in optical modulation with a broad spectral band range at the near-infrared (NIR) band.

materials science, multidisciplinary,optics
Passive mode-locked Er-doped fiber laser pulse generation based on titanium disulfide saturable absorber

Xinxin Shang,Linguang Guo,Huanian Zhang,Dengwang Li,Qingyang Yue

DOI: https://doi.org/10.1631/FITEE.2000341

2021-03-31

Abstract:In this study, titanium disulfide (TiS 2 ) polyvinyl alcohol (PVA) film-type saturable absorber (SA) is synthesized with a modulation depth of 5.08% and a saturable intensity of 10.62 MW/cm 2 by liquid-phase exfoliation and spin-coating methods. Since TiS 2 -based SA has a strong nonlinear saturable absorption property, two types of optical soliton were observed in a mode-locked Er-doped fiber laser. When the pump power was raised to 67.3 mW, a conventional mode-locked pulse train with a repetition rate of 1.716 MHz and a pulse width of 6.57 ps was generated, and the output spectrum centered at 1556.98 nm and 0.466 nm spectral width with obvious Kelly sidebands was obtained. Another type of mode-locked pulse train with the maximum output power of 3.92 mW and pulse energy of 2.28 nJ at the pump power of 517.2 mW was achieved when the polarization controllers were adjusted. Since TiS 2 -based SA has excellent nonlinear saturable absorption characteristics, broad applications in ultrafast photonic are expected.

engineering, electrical & electronic,computer science, information systems, software engineering
Fundamental frequency and second harmonic mode-locked operations in an erbium-doped fiber laser based on Cr2Sn2Te6 saturable absorbers

Shuaimeng Li,Ziting Zhao,Feng Chen,Lezheng Wang,Yutian He,Yunqi Tang,Guomei Wang,Wenfei Zhang,Shenggui Fu,Huanian Zhang,Nannan Xu,Cheng Lu

DOI: https://doi.org/10.1016/j.optmat.2024.115332

IF: 3.754

2024-04-01

Optical Materials

Abstract:With the rapid development of ultrafast photonics, the need for optical modulators is expanding. In particular, the optical modulator with a high damage threshold and the ability to generate multiple soliton states. This has prompted an ongoing search for optical modulators based on two-dimensional (2D) materials. Therefore, in this work, a novel 2D material Cr2Sn2Te6 (CSnT) with modulation depth of 6.17% and saturation intensity of 15.97 MW/cm2 is prepared as saturable absorber (SA). The nonlinear optical absorption characteristics and pulse modulation applications of CSnT are showed in the Erbium-doped fiber laser (EDFL). The fundamental frequency mode-locked operation and the second harmonic mode-locked operation are realized simultaneously in the ring cavity. Moreover, CSnT SA has a high damage threshold and high stability, the damage threshold reaches 467 mW and the signal-to-noise ratio (SNR) is higher than 70 dB. The experimental findings demonstrate that the CSnT-based saturable absorber possesses remarkable nonlinear optical properties, indicating its considerable potential in the realm of ultrafast photonics.

materials science, multidisciplinary,optics
Passively Mode-Locked Fiber Laser with a Semiconductor Saturable Absorber Mirror

WANG Jing,ZHANG Hong-ming,ZHANG Jun,YAN Meng,YAO Min-yu

DOI: https://doi.org/10.3321/j.issn:0258-7025.2007.02.003

2007-01-01

Chinese Journal of Lasers

Abstract:Using a semiconductor saturable absorber mirror(SESAM),a passively mode-locked fiber ring laser was demonstrated and stable sub-picosecond pulses were produced.The repetition frequency of pulse trains was several MHz.Nearly transform-limited 422 fs pulses with spectrum width of 6.35 nm were obtained,without any satellite pulses or pedestal.The duration of the pulses was measured by an autocorrelator with second harmonic generation,and pulses as narrow as 377 fs were achieved.During 10 hours,the laser can work stablely.The experimental setup was simple,compact,and self-started.
Few-layer bismuthene for femtosecond soliton molecules generation in Er-doped fiber laser

Chong Wang,Lu Wang,Xiaohui Li,Wenfeng Luo,Tianci Feng,Ying Zhang,Penglai Guo,Yanqi Ge

DOI: https://doi.org/10.1088/1361-6528/aae8c1

IF: 3.5

2018-11-09

Nanotechnology

Abstract:Bismuthene, a mono-elemental two-dimensional material with a novel kind of few-layer structure purely consisting of bismuth, has been predicted to have a prominent optical response and enhanced stability in theory. In this paper, few-layer bismuthene is employed as the saturable absorber. The mode-locker is fabricated by dropping bismuthene on a microfiber in a passively mode-locked, Er-doped fiber laser. The single pulse can be obtained at 122.1 mW, with 621.5 fs pulse duration at 1557.5 nm central wavelength, 10.35 nm spectral width and fundamental repetition of 22.74 MHz. Thanks to the outstanding nonlinear effect and semimetal of the bismuthene, dual-pulses, octonary-pulses and fourteen-pulses soliton molecules with tightly and loosely temporal separation can be achieved for the first time, to the best of our knowledge. The preceding indicates that bismuthene will have wide potential in many applications, such as optical fiber communications, optical logical gate, and laser materials processing, etc.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology
Femtosecond Laser Pulse Generation in an Erbium-Doped Ring Cavity Fiber Laser with A Single-Wall Carbon-Nanotube Saturable Absorber

Yue Cai,Chun Zhou,Ling Ren,Peng Li,Kaili Jiang,Zhigang Zhang

DOI: https://doi.org/10.1109/cleopr.2009.5292593

2009-01-01

Abstract:we demonstrate a new saturable absorber mirror coated with thin-film single-wall carbon nanotubes Using such a device, we build a T-type ring cavity fiber laser and obtained pulses of 586 fs
Saturable Absorber Based On A Single Mode Fiber - Graded Index Fiber - Single Mode Fiber Structure With Inner Micro-Cavity

Fan Yang,D. N. Wang,Zhaokun Wang,Liujiang Li,Chun-Liu Zhao,Ben Xu,Shangzhong Jin,Shi-Ying Cao,Zhan-Jun Fang

DOI: https://doi.org/10.1364/OE.26.000927

IF: 3.8

2018-01-01

Optics Express

Abstract:An Er-doped mode-locked fiber laser with a saturable absorber based on single mode - graded index multimode - single mode fiber (SMF-GIMF-SMF) with inner microcavity is demonstrated. The modulation depth of the saturable absorber was measured to be 1.9% when the SMF-GIMF-SMF structure is bent to a certain state. Such a simple saturable absorber enables the mode-locking operation in a ring Er-doped fiber laser and ultrafast pulses with pulse energy of 0.026 nJ and pulse width of 528 fs at the fundamental repetition rate of 14.34 MHz can be generated. In addition, the harmonic mode-locking operation can also be achieved. (c) 2018 Optical Society of America
Passive mode-locking and Q-switching of ytterbium-doped fiber lasers using Cr2S3 saturable absorbers

Junpeng Qiao,Ruoyi Zhu,Safayet Ahmed,Ranran Fan,Md. Nahian Al Subri Ivan,Guangqiang Liu,Yuen Hong Tsang,Sujuan Feng

DOI: https://doi.org/10.1007/s11082-024-07102-2

IF: 3

2024-06-03

Optical and Quantum Electronics

Abstract:In recent years, 2D Cr 2 S 3 has earned lots of attentions in the fields of photocatalysis and photodetector due to its outstanding environmental stability and high responsivity. However, up to now, the optical properties of 2D Cr 2 S 3 , especially the NLO properties of Cr 2 S 3 have been rarely studied. In this work, the NLO properties of Cr 2 S 3 -nanoparticles in 1 μm have been investigated by using open-aperture (OA) Z-scan method. The nonlinear absorption coefficient (β), modulation depth and saturable intensity are measured to be -2.6 cm/GW, 11.5%, and 0.115 MW/cm 2 , respectively. Furthermore, by depositing Cr 2 S 3 nanoparticles on a side-polished fiber and inserting into a ytterbium-doped fiber laser (YDFL) cavity, stable mode-locking laser and Q-switching laser with a pulse width of 10.2 ns and 2.95 μs are achieved, respectively. These results demonstrate that Cr 2 S 3 is a promising saturable absorber (SA) for the fiber laser applications.

engineering, electrical & electronic,optics,quantum science & technology

Erbium-doped fiber laser mode-locked with a few-layer MoS2 saturable absorber

Generation of Trapezoidal Envelope Pulses and Soliton Rains from Passively Mode-Locked Fiber Laser with MoS2 Saturable Absorber on Microfiber

980-nm Q-switched photonic crystal fiber laser by MoS 2 saturable absorber

Stable Nanosecond-Pulse Fiber Lasers Mode-Locked with Molybdenum Diselenide

Passively Mode-locked Ytterbium-doped Fiber Laser Based on MoO3 As Saturable Absorber

Wideband saturable absorption in few-layer molybdenum diselenide (MoSe2) for Q-switching Yb-, Er- and Tm-doped fiber lasers

Q-Switched pulse generation with an electro-deposited MoS2 film

Picosecond pulse generation in a mono-layer MoS2 mode-locked Ytterbium-doped thin disk laser

Evolution of Complex Pulse-Bunches in a Bound-State Soliton Fiber Laser

171st-order harmonic soliton erbium-doped fiber laser based on 2H-MoTe 2 saturable absorber

Mos2 Nanoflowers As High Performance Saturable Absorbers for an All-Fiber Passively Q-Switched Erbium-Doped Fiber Laser

C-band dual-wavelength synchronized mode-locked erbium-doped fiber laser using a common absorber

Passively Q-switched and mode-locking fiber laser based on Sb2S3 saturable absorber

Broadband saturable absorption responses of few-layered MoSe 2 nanosheets for all-solid-state Q-switched lasers

Passive mode-locked Er-doped fiber laser pulse generation based on titanium disulfide saturable absorber

Fundamental frequency and second harmonic mode-locked operations in an erbium-doped fiber laser based on Cr2Sn2Te6 saturable absorbers

Passively Mode-Locked Fiber Laser with a Semiconductor Saturable Absorber Mirror

Few-layer bismuthene for femtosecond soliton molecules generation in Er-doped fiber laser

Femtosecond Laser Pulse Generation in an Erbium-Doped Ring Cavity Fiber Laser with A Single-Wall Carbon-Nanotube Saturable Absorber

Saturable Absorber Based On A Single Mode Fiber - Graded Index Fiber - Single Mode Fiber Structure With Inner Micro-Cavity

Passive mode-locking and Q-switching of ytterbium-doped fiber lasers using Cr2S3 saturable absorbers