Abstract:Abstract Here, numerous oxygen-containing functional groups were grafted onto the surface of CNTs to improve their dispersibility in an electrolyte. The CNTs were characterized by FT-IR, Raman, XPS, FE-SEM, and TEM. The results revealed that the dispersibility of the functionalized CNTs in the composites was better than unfunctionalized CNTs. CNTs/Ni composites were deposited on a copper plate by pulsed electrodeposition and ultrasonic dispersion using an electrolytic bath with CNTs concentrations from 0 to 2 g l −1 . The friction and wear behavior of the composite coatings were assessed using two different methods. In the first method, the coatings were scratched with a progressively higher load from 0–100 N, and the results demonstrate a 10 percent reduction in the coefficient of friction (COF) of the composite compared to pure nickel. The other method involved applying a constant load of 30 N, the COF and microscopic wear mechanism were investigated at different carbon nanotube contents, and the results confirmed that the COF of the composites was gradually reduced with the increase of carbon nanotube mass concentration, and the COF was only 0.343 when the carbon nanotube content was increased to 2 g l −1 . According to the XRD results, increasing the CNTs contents changed the preferred growth orientation. Moreover, the FE-SEM images of the wear surface of the 1 g l −1 CNTs/Ni sample indicated that it had the best wear resistance and showed the smoothest wear trace without apparent cracks. The addition of CNTs enhanced the wear resistance of the nickel matrix due to the superior mechanical strength and lubricating effect of the CNTs. CNTs exposed to the matrix surface reduced the direct contact between the Ni matrix and the friction pair, acted as lubricants, and reduced the wear rate.

Friction and Wear Behavior of Electro-Deposition Ni-Cbn Composite Coatings

Friction and Wear Behavior of Electroless Ni-Based Cnt Composite Coatings

Preparation of Ni-Cnt Composite Coatings on Aluminum Substrate and Its Friction and Wear Behavior

Friction and wear behaviors of electrodeposited Ni-P-CNTs composite coatings on Al-alloy substrate

Friction and wear behavior of Ni-based carbon nanotubes composite coatings

Friction and wear behavior of Ni-P-carbon nanotubes (CNTs) electroless composite coating

Study on the friction and wear properties of nickel-based-WC-10Ni composite coatings prepared on the surface of TC4 titanium alloy

Effect of Wear Conditions on Tribological Properties of Electrolessly-Deposited Ni-P-Gr-SiC Hybrid Composite Coating

Microstructure, Mechanical Properties, and Two-Body Abrasive Wear Behavior of Cold-Sprayed 20 vol.% Cubic BN-NiCrAl Nanocomposite Coating

Electroless Preparation and Tribological Properties of Ni-P-Carbon Nanotube Composite Coatings under Lubricated Condition

Friction and Wear Behavior of Electroless Wear-Resistant and Self-Lubricating Ni-P Composite Coatings

Characterization and Wear Behaviors of Electrodeposited Ni-MoS2/SiC Composite Coating

A Research on the Friction and Wear Properties of Electroless Ni-P Composite Coating

Wear and Friction Properties of Electrodeposited Ni-Based Coatings Subject to Nano-enhanced Lubricant and Composite Coating

Wear and Friction Behavior of Plasma Sprayed NiCrMo-NiCrBSi Alloy Anti-Friction Coatings

Tribo-corrosion and mechanical performance of electro-deposited nano-composite h-BN/epoxy coating

Tribological Properties of Epoxy Composite Coatings Reinforced with Functionalized C-BN and H-BN Nanofillers

Friction and wear behavior of Ni–graphite composites prepared by electroforming

Wear Behavior of Plasma Sprayed Ni-WC Composite Coatings

Structure and tribological characteristics of nanocomposite Ti-B-N coatings

Investigation of the microstructure and tribological properties of CNTs/Ni composites prepared by electrodeposition