Abstract:In this work, two oxide-reinforced FeCrAl matrix composite coatings, FeCrAl-Al 2 O 3 and FeCrAl-Y 2 O 3 , were fabricated on a ferritic-martensitic steel by laser cladding with their microstructures probed by means of multiple characterization methods. Their cross-sections are found to consist of three zones with distinct microstructure features, i.e. cladding zone (CZ), heat-affected zone (HAZ) and substrate. Their CZs are mainly composed of columnar ferrite (the average grain sizes 7.1 ± 3.9 μm and 6.5 ± 3.8 μm for the FeCrAl-Al 2 O 3 and the FeCrAl-Y 2 O 3 coatings, respectively), with plenty of O-rich particles dispersed inside the ferrite. For the HAZs, they are essentially comprised of markedly refined martensitic laths. The average surface hardnesses of the FeCrAl-Al 2 O 3 and the FeCrAl-Y 2 O 3 coatings are 357.1 ± 8.7 HV and 348.4 ± 26.1 HV, respectively, notably higher than the substrate (264.7 ± 2.7 HV). Such effective hardening is attributed to the combined effect of solid-solution and dispersion strengthening. The wear rates of the FeCrAl-Al 2 O 3 and the FeCrAl-Y 2 O 3 coatings are 37% and 73% lower than the substrate, respectively, demonstrating considerably enhanced wear resistance. After characterizing the worn surfaces, abrasive wear and oxidative wear are confirmed to occur on all the specimens during the wear test. The enhanced wear resistance of both the composite coatings should mainly be related to the high hardnesses produced by their specific microstructural features, and the easier formation of surface oxide films during the wear.

Investigation on In-Situ Synthesizing α-Fe(Al)/Fe3Al Coating by Laser Cladding

Effect of Process Parameters on Microstructure and Properties of AlCoCrFeNi-WC-WS2 Composite Coating Prepared by Laser Cladding

Microstructure and properties of in situ synthesized Fe-Al coating by laser cladding

Laser Cladding Fe-Base Alloy Coatings Structure for Marine Hydraulic Column

Fabrication of Fe-based amorphous composite coating by laser cladding

In-situ synthesis of a FeCoCrNiCu/FeCoCrNiAl composite high entropy alloy coating by laser cladding

Study of Fe-Ni(Cr) Alloy and Nano-Al2o3 Particles Composite Coating Prepared by Laser Cladding

Influence of Scanning Speed on Microstructure and Properties of Laser Cladded Fe-Based Amorphous Coatings

Fabrication of Amorphous Coating by Laser Cladding Using Industrial-grade Fe-based Alloy

Surface microstructures and properties of oxide-reinforced FeCrAl matrix composite coatings prepared by laser cladding on a ferritic-martensitic steel

Microstructure and Properties of 35.8%Fe-20%Ti-20%Al-24%Cr-0.2%Y2O3 Coatings Prepared by Laser Cladding

Research on the laser melting coating process of an AlCoCrFeNi high‐entropy alloy

Microstructure and Wear Resistance of Laser Cladding of Fe-Based Alloy Coatings in Different Areas of Cladding Layer

Microstructure and Wear Resistance of Fe-Cr-Mo-Co-C-B Amorphous Composite Coatings Synthesized by Laser Cladding

Microstructures and corrosion resistance of Fe-based amorphous/nanocrystalline coating fabricated by laser cladding

Microstructure and wear properties of laser cladding Ti–Al–Fe–B coatings on AA2024 aluminum alloy

Study on the microstructure and properties of a laser cladding Fe–Ni–Al coating based on the invar effect

In-Situ Synthetic Tib2 Particulate Reinforced Metal Matrix Composite Coating on Aa2024 Aluminum Alloy by Laser Cladding Technology

The Property Research on High-entropy Alloy AlxFeCoNiCuCr Coating by Laser Cladding

Laser Cladding Ni35A120Fe Intermetallic Coating for Resisting High-Temperature Oxidation and Hot Corrosion

Al1.3FeCoNiCuCr HEA Coatings Produced by Laser Cladding