Abstract:Subzone tensile tests were used to quantitatively study the tensile properties along the equal toughness welded joint of a 30Cr2Ni4MoV steel ultra-supercritical steam turbine rotor. The results show that the weld metal (WM) has lower strength than the base metal (BM) but similar plasticity and work hardening properties; the heterogeneous microstructure of the heat-affected zone (HAZ) results in a gradient distribution of tensile properties. By fitting the stress-plastic strain curve based on the Hollomon equation, there are two hardening exponents n 1 and n 2 in each subzone of the welded joint. Based on the K–M curve of the hardening rate, during uniform plastic deformation before necking, the coarse-grained HAZ (CGHAZ) only experienced two work hardening stages III and IV, and other micorregions of the welded joint exhibited three work hardening stages III ~V. The exponent n 1 represents initial hardening stage III when the plastic strain is less than 0.003, and n 2 represents hardening stages IV~V when the plastic strain is greater than 0.003. The uneven distribution of the exponent n 2 along the joint is related to the differences in the microstructure (tempered martensite or bainite) and carbides. Observing the subzone specimens after tensile testing by TEM, it can be found that dislocation cells appeared in the tempered bainite matrix, which had better work hardening capability than tempered martensite. The lath martensite and granular bainite mixed microstructure and fine granular martensite are beneficial for improving the hardening capabilities and delaying the hardening period, but the carbides distributed in the high-angle grain boundaries are not conducive to strain hardening. The microstructure type, grain size and carbides dispersed in the matrix are the main factors affecting the hardening behavior of each subzone of the joint. The strength prediction model of welded joint subzones based on the hardness and the hardening exponent was established.

Microstructure Evolution in the Heat-Affected Zone of Zr -Ti Microalloyed High-Strength High-Toughness Offshore Structural Steels

Effect of Welding Processes with High Heat Input on the Microstructure and Toughness of Coarse-Grained Heat-Affected Zone of a High-Strength High-Toughness Steel

Effect of Fast Cooling on Microstructure and Toughness of Heat Affected Zone in High Strength Offshore Steel

Effect of Zr-Ti combined deoxidation on microstructure and toughness in coarse-grained region of heat-affected zone of high strength low alloy steels

Investigation of characteristic and evolution of fine-grained bainitic microstructure in the coarse-grained heat-affected zone of super-high strength steel for offshore structure

Effect of Zr-Ti Combined Deoxidation on Toughness of Coarse-Grained Heat-Affected Zone with High Heat Input Welding of Low Carbon High Strength Steels

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

Changes in microstructure and properties of weld heat-affected zone of high-strength low-alloy steel

Crystallographic Study of Transformation Products of Heat-Affected Zone and Correlation with Properties of FH690 Heavy-Gauge Marine Steel by Multi-pass Submerged Arc Welding

Microstructure and Toughness of the CGHAZ of an Offshore Platform Steel

Mechanism of Interfacial Microstructure Evolution of G115 Steel in Simulated Heat Affected Zone

Microstructure evolution of HAZ in the multi-pass underwater wet welded joints

Microstructural characteristics and impact toughness in YS690MPa steel weld metal for offshore structures

Temperature-gradient Induced Microstructure Evolution in Heat-Affected Zone of Electron Beam Welded Ti-6Al-4V Titanium Alloy

Effect of Microstructure on Local Strain Hardening Behavior along an Equal Toughness Matching Welded Joint of a 30cr2ni4mov Welded Rotor

In-situ observation of grain refinement in the simulated heat-affected zone of high-strength low-alloy steel by Zr-Ti combined deoxidation

Study of the impact properties and microstructure evolution in a high-strength low-alloy heavy steel

Mechanism of BN-Promoting Acicular Ferrite Nucleation to Improve Heat-Affected Zone Toughness of V-N-Ti Microalloyed Offshore Steel

Effect of Microstructure on High-Strength Low-Alloy Steel Welded Joint Toughness with Simulation of Heat-Affected Zone Coarse-Grained Area

Coarse Grained Region Microstructure and Properties of High Heat Input Welding DH36 Steels

Microstructure and Local Mechanical Properties of the Heat-Affected Zone of a Resistance Spot Welded Medium-Mn Steel