Abstract:This article is devoted to the experimental study of tuning method for an Alvarez-type drift tube linac (DTL) of the Compact Pulse Hadron Source (CPHS) project at Tsinghua University. The biperiodic structure based on the post couplers are introduced to overcome the instability of the Alvarez DTL tank which is used to operate in 0 (or 2π) mode. The experimental method and results are presented, and the tuning scheme for the formal CPHS DTL is summarized from the tuning experiment. INTRODUCTION The effective shunt impedance of the Alvarez-type DTL is typically high when it operates in a typical 0 (or 2π) mode with the group velocity of 0. But the structure is very susceptible to perturbation such as the beam loading, mechanical and installation error, because of the narrow space near the adjacent modes on the TM dispersion curve. The post couplers, which are the resonant-coupling elements constitutionally, are mounted on the wall of the DTL cavity oppositely and alternatively to introduce a new PCs (post couplers) dispersion curve. When the stopband between the two passbands of the dispersion curves disappears by adjusting the slugging length of the post couplers, the lowest frequency of the TM passband will be moved to the π/2 mode point of the new dispersion curve. Therefore the new stable biperiodic structure of the DTL will be achieved [1]. To verify the tuning method, one model cavity has been machined and the turning experiment is carried out based on the cavity. The cavity is designed and manufactured for verifying the mechanical design and undertaking some low-power experiment. The model cavity consists of ten full drift tubes, two half drift tubes mounted on the end flanges, three post couplers and two tuners [2]. The end of the post couplers is designed to be eccentric to facilitate the tuning of the local field distribution by rotating the post. TUNING EXPERIMENTAL CONFIGURATION On the experimental stand as shown in Fig. 1, the measurement based on the bead-pull method is executed. According to the perturbation theory, when the bead is pulled into the field between the two adjacent drift tubes, the resonant frequency changes. Then the corresponding phase shift can be detected by a vector network analyzer (VNA) and the electric field along the beam-axis can be deduced [3]. Figure: 1 Tuning experimental stand. A stepping motor is adopted to pull a fine nylon line on which the small perturbation bead is fixed. The size of the bead shall be rather appropriate, so that the responsive signal caused by the bead is big enough compared with the background noise and at the same time within the linear range of the phase around the resonant frequency. It depends on the Q factor of the cavity. The Q factor of this model cavity is measured as 17796 which is about 44% of the designed value. It is because that the surfaces of the interior copper-plated cavity wall and the aluminous end flanges are oxidic. With the value of the Q factor, the radius of the bead is determined as 0.7 mm by estimation. To ensure the accuracy of the measurement, the peak field is employed to represent the field distribution instead of the integral one due to its further advantages [4]. Before the measurement, the reproducibility is checked. The reproducibility Rij is defined by Eq. (1).

Calculations for Shortening the Bunch Length in Storage Rings Using A Harmonic Cavity

Bunch lengthening affected by the short-range effect of resonant modes in radio-frequency cavities

Bunch Lengthening of the HALF Storage Ring in the Presence of Passive Harmonic Cavities

Multiple-bunch-length operating mode design for a storage ring using hybrid low alpha and harmonic cavity method☆

Lifetime increase using a passive higher harmonic cavity for Hefei Light Source Ⅱ

Periodic Transient Beam Loading Effect with Passive Harmonic Cavities in Electron Storage Rings

Tracking Simulations for the HLS- II with a Passive Harmonic Cavity in the Symmetric and Asymmetric Fill Patterns

Design and Simulation of a high order mode cavity bunch length monitor

Study of Robinson Instabilities with A Higher-Harmonic Cavity for the Hls Phase Ii Project

Equilibrium of an Arbitrary Bunch Train in the Presence of Multiple Resonator Wake Fields

Broadband Impedance Calculations and Single Bunch Instabilities Estimations of of the HLS-II Storage Ring

Design of a L-band Cavity Optimized for Robinson Instability in the TTX-II Storage Ring

Calculations of space-charge tune shifts in storage rings with extremely short bunches and small bunch spacing

Preliminary Study of EEHG-based Superradiant Undulator Radiation at the HLS-II Storage Ring

A low-frequency normal conducting cavity with higher-order mode damping for fourth-generation synchrotron radiation sources

Lattice design and beam lifetime study for HLS storage ring upgrade project

Experimental Study of Tuning Method on a Model Alvarez DTL Cavity for CPHS Project

A Low Emittance Lattice Design For Hls Storage Ring

Rf Deflecting Cavity for Bunch Length Measurement in Tsinghua Thomson Scattering X-Ray Source

Harmonic Generation and Bunch Compression Based on Transverse-Longitudinal Coupling

Linear Optics Compensation of the Superconducting Wiggler in HLS