Abstract:Magnesium alloys have received much attention for their lightweight and other excellent properties, such as low density, high specific strength, and good castability, for use in several industrial and commercial applications. However, both magnesium and its alloys show limited room-temperature formability owing to the limited number of slip systems associated with their hexagonal close-packed crystal structure. It is well known that crystallographic texture plays an important role in both plastic deformation and macroscopic anisotropy of magnesium alloys. Many authors have concentrated on improving the room- temperature formability of Mg alloys. However, despite having a lot of excellent properties in magnesium alloy, the study for various properties of magnesium alloy have not been clarified enough yet.Mg alloys are known to have a good damping capacity compared to other known metals and their alloys. Also, the damping properties of metals are generally recognized to be dependent on microstructural factors such as grain size and texture. However, there are very few studies on the relationship between the damping capacity and texture of Magnesium alloys. Therefore, in this study, specimens of the AZ31 magnesium alloy, were processed by hot working, and their texture and damping property investigated. A 60 mm × 60 mm × 40 mm rectangular plate was cut out by machining an ingot of AZ31 magnesium alloy (Mg-3Al-1Zn in mass%), and rolling was carried out at 673 K to a rolling reduction of 30%. Then, heat treatment was carried out at temperatures in the range of 573-723 K for durations in the range of 30-180 min. The samples were immediately quenched in oil after heat treatment to prevent any change in the microstructure. Texture was evaluated on the compression planes by the Schulz reflection method using nickel-filtered Cu Kα radiation. Electron backscatter diffraction measurements were conducted to observe the spatial distribution of various orientations. Specimens for damping capacity measurements were machined from the rolled specimen, to have a length of 120 mm, width of 20 mm, and thickness of 1 mm. The damping capacity was measured with a flexural internal friction measurement machine at room temperature. It was found that the damping capacity increases with both increasing heat-treatment temperature and time, due to grain growth and the increased pole densities of textures.

Effect of Different Heat Treatment Process on Damping Peak of 6061al/sic P MMC Produced by Spray Codeposition

Unveiling Thermal and Athermal Effects in Strain Hardening Removal of A6061 Aluminum Alloy

Study on effects of heat treatment on morphology of Al coating on the surface of Mg alloy by cold spray

Effect of SiC coating and heat treatment on damping behavior of C/SiC composites

Effect of High-Density Pulsed Electric Current on the Formability of Aluminum Alloy

Effects of post-deposition processing on static and cyclic performance of cold sprayed 6061 aluminum alloy

Effect of hot working on the damping capacity and mechanical properties of AZ31 magnesium alloy

Effects of different heat treatments on anisotropy of cold sprayed 7075 Al deposits

Effects of different heat treatment temperatures on the microstructure and mechanical properties of additive manufacturing Ti65 alloys

The effects of heat treatment on the extrusion-induced inhomogeneity of spray-formed aluminum alloy 7055

Damping performance of SiC nanoparticles reinforced magnesium matrix composites processed by cyclic extrusion and compression

The Effect of Hot Forming–Quenching and Heat Treatment Processes on the Mechanical Properties of AA6016 Aluminum Alloy Sheets

Achieving high-damping NiTip/7075Al composites with controllable phase transformation behavior fabricated by friction stir processing

Combined Effect of Particle Reinforcement and T6 Heat Treatment on the Compressive Deformation Behavior of an A357 Aluminum Alloy at Room Temperature and at 350 °C

Effect of heat treatment and extrusion processing on the microstructure and mechanical properties of spray formed 7055 alloy

Microstructure and damping property of Mn-Cu damping alloy by induction brazing and different heat treating

Effect of Heat Treatment on the Mechanical and Tribological Properties of Dual-Reinforced Cold-Sprayed Al Coatings

Effect of Heat Treatment on Mechanical Properties and Thermal Expansion of Al6063-SiC-Graphite, Molybdenum Disulfide Hybrid Composite

Effect of heat treatment on the microstructure and mechanical properties of spray formed 7055 aluminum alloy TIG welded joints reinforced by ZrB 2 / Al 3 (Sc, Zr) particles

Effect of Heat Treatment on the Microstructure and Vickers Hardness of Aluminum Alloy Gradient Plate Prepared Through Friction Stir Processing

Role of In-Situ Dynamic Splat Sintering on Elastic and Damping Behavior of Cold Sprayed Aluminum Coatings