Plastic Zone and Opening Displacement for an Asymmetrical Fast Propagating Semi-Infinite Crack in A Strip

XC Yang,TY Fan

DOI: https://doi.org/10.1007/978-1-4613-0269-8_26

2000-01-01

Abstract:In this paper, the problems of the generalized Dugdale model for a semi-infinite fast propagating crack asymmetrically in a strip have been discussed. The plastic zone and crack tip opening displacement are given in both cases.

What problem does this paper attempt to address?

Exact Solution to the Problem of A Half-Plane Crack in A Transversely Isotropic Piezoelectric Body Subjected to Antisymmetric Tangential Point Forces

PF Hou,HJ Ding,FL Guan

2001-01-01

Acta Mechanica Solida Sinica

Abstract:An exact and complete solution of the problem of a half-plane crack in an infinite transversely isotropic piezoelectric body is presented. The upper and lower crack faces are assumed to be loaded antisymmetrically by a couple of tangential point forces in opposite directions. The solution is derived through a limiting procedure from that of a penny-shaped crack. The expressions for the electroelastic field are given in terms of elementary functions. Finally, the numerical results of the second and third mode stress intensity factors k(2) and k(3) of piezoelectric materials and elastic materials are compared in figures.
Finite Element Analysis of Crack Dynamic Response in Gradient Non- Homogeneous Finite Plate

GAI Bing-zheng,ZHANG Yong-qiang

DOI: https://doi.org/10.3321/j.issn:0367-6234.2005.12.010

2005-01-01

Abstract:The wave finite element method was used to study the dynamic response under impact loading in a gradient non-homogeneous plate with a crack.The dynamic stress intensity factors(DSIFs) of the crack-tip can be obtained by interpolations for the width of a crack and the distance from the crack-end.A gradient non-homogeneous finite crack plate with the unidirectional linear elastic modulus under exponent attenuation impact load was concretely analyzed numerically.The results show that however the crack length and gradient parameter of the plate materials are changed,dynamic stress intensity factors at the crack-tip rapidly rise and then slowly fall with time.The crack-tip dynamic stress intensity factors decrease with the decrease of the crack length and the increase of the functionally gradient parameter.
Penny-Shaped Dugdale Crack in a Transverse Isotropic Medium

X. Y. Li,D. Yang,W. Q. Chen,G. Z. Kang

DOI: https://doi.org/10.1007/s10704-012-9720-4

IF: 2.635

2012-01-01

International Journal of Fracture

Abstract:Analytical results for a penny-shaped crack with a plastic zone at the crack front are given. The crack is embedded in an infinite transversely isotropic elastic medium and is assumed to be subjected to two identical axisymmetric loads on the upper and lower crack faces. The size of the plastic zone at the crack front is determined by applying Dugdale hypothesis to the elasticity results for a penny-shaped crack. The size of the plastic zone is derived in terms of hyper-geometric functions. Expression of the normal stress outside the plastic zone is also given.
A PENNY-SHAPED CRACK IN AN INFINITE PIEZOELECTRIC BODY UNDER ANTISYMMETRIC POINT LOADS

Hou Peng-fei,Ding Hao-jiang,Guan Fu-ling

DOI: https://doi.org/10.1631/jzus.2001.0146

2001-01-01

Journal of Zhejiang University SCIENCE A

Abstract:In this study, Fabrikant (1989, 1991)'s new results in potential theory were used to obtain the exact and complete solution for the problem of a penny-shaped crack in an infinite transversely isotropic piezoelectric body subjected to antisymmetric point loads (point charges and normal point forces); then the complete solution for the problem of one-sided loading of a penny-shaped crack was obtained by the superposition of the symmetric loading solution in Chen and Shioya (1999) and the antisymmetric one presented here; and then the reciprocity theorem of piezoelectric media was used to deal with the problem of interaction between arbitrarily located point forces and a point charge with a penny-shaped crack and obtained the exact expressions of the crack faces' normal displacement in terms of elementary functions and some non-singular integrals; and finally obtained the normal displacement of the positive and negative faces of the crack under many loading cases as shown in figures for an infinite PZT-4 piezoelectric ceramic body weakened by a penny-shaped crack.
CIRCULAR CRACK IN A TRANSVERSELY ISOTROPIC PIEZOELECTRIC SPACE UNDER POINT FORCES AND POINT CHARGES

Hou Pengfei,Ding Haojiang,Guan Fuling

DOI: https://doi.org/10.1016/s0167-8442(01)00075-1

2002-01-01

Abstract:In this paper,two kinds of circular crack including external circularcrack and penny-shaped crack in a transversely isotropic piezoelectric space are con-sidered.Firstly,we obtain the solution to the problem of an external circular crack ina transversely isotropic piezoelectric space subjected to antisymmetric normal pointforces and point charges.Based on this,the solution of one-sided loading of an ex-ternal circular crack is constructed.Secondly,the real shape of an external circularcrack and the opening displacement of a penny-shaped crack under an arbitrary pointforce and point charge are further obtained.At last,the results are presented in agraphical form.
Penny-Shaped Dugdale Crack in A Transversely Isotropic Medium and under Axisymmetric Loading

Xiang-Yu Li,Shui-Tao Gu,Qi-Chang He,Wei-Qiu Chen

DOI: https://doi.org/10.1177/1081286512437395

2013-01-01

Mathematics and Mechanics of Solids

Abstract:The present work is concerned with a penny-shaped crack embedded in a transversely isotropic medium and oriented in parallel with the isotropic plane of the latter. Three axisymmetric crack problems are investigated. In the first one, the upper and lower lips of the crack are subjected to a pair of annular opposite pressures. In the second and third problems, two opposite concentrated forces of the same magnitude are applied successively at the upper and lower crack lip centres and at any two points outside the crack and on the axis perpendicular to the crack. Using the basic idea underlying Dugdale's crack model, the extent of the plastic zone is analytically estimated in each of the three cases. In addition, the corresponding crack surface displacement is determined explicitly. Numerical examples are provided to discuss the effects of some geometrical and material parameters involved. Apart from their own usefulness in carrying out some simplified crack analyses, the results obtained in this work can in particular serve as benchmarks for computational fracture mechanics.
A Penny-Shaped Crack in an Infinite Linear Transversely Isotropic Medium Subjected to Uniform Anti-Symmetric Heat Flux: Closed-form Solution

Jing Yang,Xianyu Jin,Nanguo Jin

DOI: https://doi.org/10.1016/j.euromechsol.2014.05.003

IF: 4.873

2014-01-01

European Journal of Mechanics - A/Solids

Abstract:The problem of a penny-shaped crack subjected to anti-symmetric uniform heat flux in an infinite transversely isotropic magneto-electro-thermo-elastic medium is investigated. Although we start our derivations in magneto-electro-thermo-elastic medium, the solution presented in this paper is also applicable for linear transversely isotropic thermopiezoelectric, thermopiezomagnetic, thermoelastic materials. Previous researchers obtained the closed-form solution to the similar problem in crack plane. In regards to full-space solution, they expressed it in multiple integration or line integrals involving Bessel functions. In this article, the authors find that the full-space solution could be in terms of the explicit elementary functions via potential theory method developed by Fabrikant. What's more, the closed form solutions in all kinds of linear transversely isotropic medium can serve as benchmarks for future numerical studies of multiphase composites.
Plastic Zone of Semi-Infinite Crack in Planar Kagome and Triangular Lattices

Xinming Qiu,Lianghong He,Yueqiang Qian,Xiong Zhang

DOI: https://doi.org/10.1016/s0894-9166(09)60268-8

2009-01-01

Abstract:The fracture investigations of the planar lattices made of ductile cell walls are currently limited to bending-dominated hexagonal honeycomb. In this paper, the plastic zones of stretching-dominated lattices, including Kagome and triangular lattices, are estimated by analyzing their effective yield loci. The normalized in-plane yield loci of these two lattices are almost identical convex curves enclosed by 4 straight lines, which is almost independent of the relative density but is highly sensitive to the principal stress directions. Therefore, the plastic zones around the crack tip of Kagome and triangular are estimated to be quite different to those of the continuum solid and also hexagonal lattice. The plastic zones predictions by convex yield surfaces of both lattices are validated by FE calculations, although the shear lag region caused by non-local bending effect in the Kagome lattice enlarges the plastic zone in cases of small ratio of r p /l.
Analysis on cohesive crack opening displacement considering the strain softening effect

Limin Wang,Shilang Xu,Xiqiang Zhao

DOI: https://doi.org/10.1007/s11433-005-0089-5

2006-01-01

Science in China Series G

Abstract:In order to investigate the crack propagation in quasi-brittle materials like rock, ceramic and concrete, Hillerborg and his co-researchers abstracted the fracture process zone in front of a stress free crack in terms of a “fictitious crack zone”. On the fictitious crack zone, cohesive stresses distribute following a given softening relationship of stress vs. crack opening. Based on the polynomial or power series expression of cohesive crack opening displacement, the relationship of the cohesive stress vs. the crack opening displacement is established using elastic theory and integral equation, and some unknown physics variables are obtained using variation approach. The calculation results gained in this paper are close to the experimentally test ones.
Computation of the crack opening displacement in the phase-field model

Lin Chen,Zhao Wang,Bin Li,René de Borst

DOI: https://doi.org/10.1016/j.ijsolstr.2023.112496

IF: 3.667

2023-09-01

International Journal of Solids and Structures

Abstract:The phase-field model treats discrete cracks in a smeared sense by a regularisation technique. It holds attractive properties: there is no need to consider cracks as geometric discontinuities, and it avoids remeshing around crack tips. The method has been employed in the analysis of brittle and cohesive fracture problems. In the brittle fracture model, a Griffith-like energy functional is used in the simulation, while in the cohesive fracture model, the fracturing problem exploits a displacement jump governed energy functional. Obviously, the displacement jump is crucial in the cohesive fracture model and in certain other applications, e.g. for hydraulic fracturing. In the current study, the approximated form of the crack opening displacement is derived for the brittle and cohesive fracture models. In both models, the crack opening displacement is associated with a line integral normal to the crack, but different factors in front of the integral apply. The derived integrals are verified analytically in a one-dimensional setting and numerically in multi-dimensional set-ups, featuring straight and curved cracks.

mechanics
Speed-Dependent Tip Fields of A Moving Crack in A Hyperelastic Material

J. Wu,C. Q. Ru

DOI: https://doi.org/10.1177/1081286512438875

2012-01-01

Mathematics and Mechanics of Solids

Abstract:This paper gives an asymptotic analysis of plane strain deformation and stress fields near the tip of a steady moving crack in a compressible hyperelastic material. The semi-infinite crack is assumed to be in an infinite homogeneous harmonic material under a constant remote mode-I loading. The crack tip deformation and stress fields are derived up to the third order, which ensures the strict positivity of the Jacobian determinant in the vicinity of the moving crack tip. The derived solutions are applied to a specific hyperelastic material for which some recent experimental data are available in the literature. The comparison with the experimental data showed that the crack-face profile and the energy release rate predicted by the present model are in reasonable agreement with experiments and several recent finite-strain elastic models. In addition, the crack branching angle predicted by the present model also agrees well with some known experimental data. All of these results suggest that the harmonic material model has the potential to capture the main features of finite deformation phenomena in the dynamic fracture of hyperelastic materials.
Crack tip fields and fracture resistance parameters based on strain gradient plasticity

V. Shlyannikov,E. Martínez-Pañeda,A. Tumanov,A. Tartygasheva

DOI: https://doi.org/10.1016/j.ijsolstr.2020.10.015

IF: 3.667

2021-01-01

International Journal of Solids and Structures

Abstract:The crack tip mechanics of strain gradient plasticity solids is investigated analytically and numerically. A first-order mechanism-based strain gradient (MSG) plasticity theory based on Taylor's dislocation model is adopted and implemented in the commercial finite element package ANSYS by means of a user subroutine. Two boundary value problems are considered, a single edge tension specimen and a biaxially loaded plate. First, crack tip fields are characterized. Strain gradient effects associated with dislocation hardening mechanisms elevate crack tip stresses relative to conventional plasticity. A parametric study is conducted and differences with conventional plasticity predictions are quantified. Moreover, the asymptotic nature of the crack tip solution is investigated. The numerical results reveal that the singularity order predicted by the first-order MSG theory is equal or higher to that of linear elastic solids. Also, the crack tip field appears not to have a separable solution. Moreover, contrarily to what has been shown in the higher order version of MSG plasticity, the singularity order exhibits sensitivity to the plastic material properties. Secondly, analytical and numerical approaches are employed to formulate novel amplitude factors for strain gradient plasticity. A generalized J-integral is derived and used to characterize a nonlinear amplitude factor. A closed-form equation for the analytical stress intensity factor is obtained. Amplitude factors are also derived by decomposing the numerical solution for the crack tip stress field. Nonlinear amplitude factor solutions are determined across a wide range of values for the material length scale <math>l</math> and the strain hardening exponent <math>N</math>. The domains of strain gradient relevance are identified, setting the basis for the application of first-order MSG plasticity for fracture and damage assessment.
Mechanics of dynamic debonding

W Yang,Zhigang Suo,C. F. Shih

DOI: https://doi.org/10.1098/rspa.1991.0070

1991-06-08

Abstract:Singular fields around a crack running dynamically along the interface between two anisotropic substrates are examined. Emphasis is placed on extending an established frame work for interface fracture mechanics to include rapidly applied loads, fast crack propagation and strain rate dependent material response. For a crack running at non-uniform speed, the crack tip behaviour is governed by an instantaneous steady-state, two-dimensional singularity. This simplifies the problem, rendering the Stroh techniques applicable. In general, the singularity oscillates, similar to quasi-static cracks. The oscillation index is infinite when the crack runs at the Rayleigh wave speed of the more compliant material, suggesting a large contact zone may exist behind the crack tip at high speeds. In contrast to a crack in homogeneous materials, an interface crack has a finite energy factor at the lower Rayleigh wave speed. Singular fields are presented for isotropic bimaterials, so are the key quantities for orthotropic bimaterials. Implications on crack branching and substrate cracking are discussed. Dynamic stress intensity factors for anisotropic bimaterials are solved for several basic steady state configurations, including the Yoffe, Gol’dshtein and Dugdale problems. Under time-independent loading, the dynamic stress intensity factor can be factorized into its equilibrium counterpart and the universal functions of crack speed.
Crack Propagation In Viscoplastic Polymers: Heat Generation In Near-Tip Zone And Viscoplastic Cohesive Model

y t chen,k x liu

DOI: https://doi.org/10.1063/1.4908115

IF: 4

2015-01-01

Applied Physics Letters

Abstract:We develop a precise experimental method to measure the full-field heat-generating process near moving (mode I) crack tips in polycarbonate films and present the experimental image of crack tip structure in viscoplastic polymers. A viscoplastic cohesive model is constructed to analyze the mechanical state and temperature increase in near-tip zone during steady crack propagation. The cohesive stress in this model is uniquely characterized by viscoplastic constitutive equation instead of traction-separation displacement relationship or constant yield stress, which greatly differs from previous models. Our proposed model's prediction of temperature increase agrees well with the experimental result. (C) 2015 AIP Publishing LLC.
A Gradient-Enhanced Plasticity Based Phase-Field Model for Ductile Fracture Simulations

Huan Li,Wenyu Zhang,Xiang Cheng

DOI: https://doi.org/10.1142/s0219876222500396

IF: 1.7

2022-01-01

International Journal of Computational Methods

Abstract:Ductile fracture is modeled by using a novel phase-field method of geometric type to avoid the use of the complicated discretization approaches for crack discontinuities. The plasticity model is defined by an over-nonlocal implicit gradient-enhanced framework, which is equivalent to the integral-type plasticity models and therefore strongly nonlocal. A modified phenomenological barrier function is used as the crack phase-field driving force by mainly considering the effects of the nonlocal plastic deformation under shear-dominated stress states. The ductile damage is assumed to solely affect the plastic energy stored capacity from the micro-mechanical perspective such that the proposed approach can be easily extended to more general loading conditions. The implementation of the proposed phase-field method is shown to be easily integrated into the commercial codes (e.g., ABAQUS) through the coupling use of several user interfaces. We present simulations of the shear band formation under axial compression and the ductile crack propagations in a single-edged notched plate, a slanted fracture specimen and a pure shear test specimen to elucidate the viability of the current nonlocal method. The numerical results adequately demonstrate that mesh dependency can be apparently alleviated if material softening occurs.
A peridynamic approach to solving general discrete dislocation dynamics problems in plasticity and fracture: Part I. Model description and verification

Wenbo Dong,Hengjie Liu,Juan Du,Xu Zhang,Minsheng Huang,Zhenhuan Li,Ziguang Chen,Florin Bobaru

DOI: https://doi.org/10.1016/j.ijplas.2022.103401

IF: 8.5

2022-10-01

International Journal of Plasticity

Abstract:In this paper, we present a peridynamic (PD)-based solution for discrete dislocation dynamics (DDD) problems using the superposition (SP) framework. By replacing the classical surface traction in the complementary problem with a nonlocal/peridynamic one, the SP DDD-PD scheme can simulate arbitrary domains, including those with pre-damage, cracks, and voids of arbitrary shapes, without explicitly tracking boundaries, interfaces, cracks, etc. The new SP DDD-PD scheme is verified for the boundary value problems (BVPs) for single dislocation, multiple dislocations, dislocation emitted from a crack tip, and dislocation-void interaction. The numerical results are compared with those from other existing schemes: the discrete-continuous (DC) DDD-PD, and the SP DDD-FEM. The new SP DDD-PD is more accurate than the DC DDD-PD scheme, especially near dislocation cores and in problems with dislocations near defects (damage or interfaces). The high accuracy of the new SP DDD-PD near dislocation cores makes it suitable to model dislocation-based plasticity and fracture, problems that are studied in part II of this work.

materials science, multidisciplinary,engineering, mechanical,mechanics
FEM Solutions for Plane Stress Mode-I and Mode-Ii Cracks in Strain Gradient Plasticity

Qiu Xinming,Guo Tianfu,Huang Kezhi,Hwang Kehchih

DOI: https://doi.org/10.1007/bf02879803

2000-01-01

Science China Mathematics

Abstract:The strain gradient plasticity theory is used to investigate the crack-tip field in a power law hardening material. Numerical solutions are presented for plane-stress mode I and mode II cracks under small scale yielding conditions. A comparison is made with the existing asymptotic fields. It is found that the size of the dominance zone for the near-tip asymptotic field, recently obtained by Chen et al., is on the order 5% of the intrinsic material length I. Remote from the dominance zone, the computed stress field tends to be the classical HRR field. Within the plastic zone only force-stress dominated solution is found for either mode I or mode II crack.
Closed-form field in an infinite space of transversely isotropic multiferroic composite medium with an elliptical or penny-shaped crack: 3D exact analysis

x y li,r f zheng,g z kang,w q chen,rolf muller

DOI: https://doi.org/10.1016/j.ijsolstr.2015.10.026

IF: 3.667

2016-01-01

International Journal of Solids and Structures

Abstract:This paper studies the mode I problem of an elliptical or penny-shaped crack contained in an infinite space of multiferroic composite material with transverse isotropy. Closed-form analytical solutions and numerical results are presented in this work in a systematic way. The crack is postulated to be either electrically/magnetically permeable or impermeable. For the first time, boundary integro-differential equations, corresponding to the crack with different magneto-electric properties, are established using the generalized method of potential theory in conjunction with the static general solutions. For four physical cases, closed-form coupled magneto-electro-elastic field variables in the space are explicitly obtained. Crack surface displacement, generalized stress intensity factor and crack compliance matrix generalized from the rock mechanics all turn out to be an intrinsic combination of a material factor and a geometrical factor. The weak and strong interactions in multiferroic composite media are exhaustively accounted for. The obtained analytical solutions may serve as benchmarks for numerous forthcoming simplified and numerical studies.
Analytical solution of the stress field and plastic zone at the tip of a closed crack

Guanzhong Wu,Wensong Wang,Shaochi Peng

DOI: https://doi.org/10.3389/feart.2024.1370672

IF: 2.9

2024-03-20

Frontiers in Earth Science

Abstract:The investigation of stress field and plastic zone distribution at the closed crack tip provides a fundamental basis for failure analysis and life prediction of geotechnical materials. Closed crack is a common crack in geotechnical materials. Studying the distribution of stress field and plastic zone at the tip of closed crack can provide theoretical basis for stability evaluation of geotechnical structures. In this study, we employ the superposition principle to obtain complex function solutions for the stress field and displacement field at the crack tip. Furthermore, we analyze the plastic zone distribution at the crack tip based on the Mohr Coulombs criterion. We investigate how factors such as crack angle, confining pressure, and material properties influence the stress field, displacement field, plastic zone size, and crack propagation direction. Our results demonstrate that this method effectively characterizes the distribution of stress field and displacement field at closed crack tips. Moreover, we elucidate that wing cracks are primarily formed due to tension-shear coupling effects. The solutions for the stress field and displacement field at the crack tip are obtained using the superposition principle. The distribution of the plastic zone at the crack tip is analyzed based on the M-C (Mohr-Coulomb) criterion. Subsequently, an analysis is conducted to investigate the influence of crack angle, confining pressure, and material properties on stress field, displacement field, plastic zone, and crack propagation direction. Lower crack angles and higher confining pressures effectively suppress slip between crack surfaces by reducing tension-shear coupling effects and inhibiting wing foil crack development. The results further indicate that the rock cohesion and internal friction angle exert negligible influence on the stress field, displacement field, plastic zone shape at the crack tip, as well as the growth direction of new cracks. The results demonstrate the effective representation of stress field and displacement field at the closed crack tip using this method. The stress distribution at the crack tip reveals that the tension-shear coupling effect primarily contributes to wing crack formation. Lower crack angles and higher confining pressures effectively suppress surface slip, reduce tension-shear coupling effects, and inhibit wing crack propagation. Furthermore, material properties do not influence the crack propagation angle, stress field, or displacement field.

geosciences, multidisciplinary
Driving Force on Line Fracture Process Zone and Fracture Parameters Suitable for Elastic–plastic Materials

Longkun Lu,Zhanli Liu,Yinan Cui,Zhuo Zhuang

DOI: https://doi.org/10.1016/j.ijsolstr.2021.01.030

IF: 3.667

2021-01-01

International Journal of Solids and Structures

Abstract:The driving force on the line, zero height, fracture process zone (FPZ) is investigated in this paper. First, basic laws for crack propagation based on the configurational force approach are derived in the framework of traditional continuum mechanics. The driving force on steady line FPZ is a direct consequence of these derivations. Fracture parameters suitable for growing cracks in elastic–plastic materials such as near tip integrals based on the incremental theory of plasticity, the energy-, displacement-, and strain-type parameters are consistent with the driving force on steady line FPZ. Therefore, the steady line FPZ has provided a unified framework encompassing the fracture parameters of stable crack growth in elastic–plastic bodies. Besides, the driving force on non-steady line FPZ is also derived, which consists of the driving force related to the self-expansion of FPZ and the driving force corresponding to the translation of FPZ. Before the crack initiation, the work of separation in the cohesive zone model (CZM) is associated with the self-expansion driving force. During the steady-state crack growth, the work of separation is equal to the translation driving force. Since the translation driving force is independent of the self-expansion driving force, the cohesive parameters at the crack initiation can differ from those during the steady-state phase.

Plastic Zone and Opening Displacement for an Asymmetrical Fast Propagating Semi-Infinite Crack in A Strip

Exact Solution to the Problem of A Half-Plane Crack in A Transversely Isotropic Piezoelectric Body Subjected to Antisymmetric Tangential Point Forces

Finite Element Analysis of Crack Dynamic Response in Gradient Non- Homogeneous Finite Plate

Penny-Shaped Dugdale Crack in a Transverse Isotropic Medium

A PENNY-SHAPED CRACK IN AN INFINITE PIEZOELECTRIC BODY UNDER ANTISYMMETRIC POINT LOADS

CIRCULAR CRACK IN A TRANSVERSELY ISOTROPIC PIEZOELECTRIC SPACE UNDER POINT FORCES AND POINT CHARGES

Penny-Shaped Dugdale Crack in A Transversely Isotropic Medium and under Axisymmetric Loading

A Penny-Shaped Crack in an Infinite Linear Transversely Isotropic Medium Subjected to Uniform Anti-Symmetric Heat Flux: Closed-form Solution

Plastic Zone of Semi-Infinite Crack in Planar Kagome and Triangular Lattices

Analysis on cohesive crack opening displacement considering the strain softening effect

Computation of the crack opening displacement in the phase-field model

Speed-Dependent Tip Fields of A Moving Crack in A Hyperelastic Material

Crack tip fields and fracture resistance parameters based on strain gradient plasticity

Mechanics of dynamic debonding

Crack Propagation In Viscoplastic Polymers: Heat Generation In Near-Tip Zone And Viscoplastic Cohesive Model

A Gradient-Enhanced Plasticity Based Phase-Field Model for Ductile Fracture Simulations

A peridynamic approach to solving general discrete dislocation dynamics problems in plasticity and fracture: Part I. Model description and verification

FEM Solutions for Plane Stress Mode-I and Mode-Ii Cracks in Strain Gradient Plasticity

Closed-form field in an infinite space of transversely isotropic multiferroic composite medium with an elliptical or penny-shaped crack: 3D exact analysis

Analytical solution of the stress field and plastic zone at the tip of a closed crack

Driving Force on Line Fracture Process Zone and Fracture Parameters Suitable for Elastic–plastic Materials