Recent Progress in Erbium- Doped Optical Glass Waveguide Amplifiers

陈海燕,官周国,刘永智

DOI: https://doi.org/10.3969/j.issn.1001-5868.2000.06.002

2000-01-01

Abstract:The principle and structure of rare- earth - doped glass integrated optical waveguide amplifiers are introduced, along with the fabrication process. Recent progress and future development are also described.

What problem does this paper attempt to address?

Er–Tm co-doped materials for on-chip ultra-broadband waveguide amplifier

Yuanzhi Chen,Zhengkai Li,Mingjie Zhang,Junchang Lu,Zhanbo Wen,Banghu Wei,Xuefei Ke,Yan Li,Shunyu Yao,Jiayue Xu

DOI: https://doi.org/10.1016/j.ceramint.2024.02.123

IF: 5.532

2024-02-01

Ceramics International

Abstract:On-chip ultra-wideband optical waveguide amplifiers are crucial for short-distance optical interconnections that utilize wavelength division multiplexing (WDM) technology. Silicon optical amplifiers still face significant challenges due to the indirect-band-gap nature and low rare earth solubility of silicon. This paper prepared a series of Er3+-Tm3+ co-doped La2O3–Al2O3 glasses that are expected to be used in on-chip ultra-broadband optical waveguide amplifiers by aerodynamic levitation (ADL) technique, and further studied their luminescence characteristics and energy transfer process. Research results indicate that the glass composition 5Er2O3-0.6Tm2O3-43.4La2O3–51Al2O3 is an optimal optical waveguide amplifier host material due to its excellent luminescence properties and ultra-broadband flat photoluminescence spectrum extending up to 440 nm. Moreover, positive gain can be obtained with a population ratio greater than 0.2, which further illustrates its feasibility as a matrix material for ultra-broadband optical waveguide amplifiers. The advancement of this material is expected to significantly aid in the fabrication and progress of next-generation ultra-wideband optical waveguide amplifiers.

materials science, ceramics
Toward a10 dB net-gain waveguide amplifier in an Er3+-Yb3+ co-doped phosphate glass

Xiangyu Sun,Zhi Chen,Liaolin Zhang,Daoyuan Chen,Yuying Wang,Beibei Xu,Zhijun Ma,Giuseppe Barillaro,Lijing Zhong,Jianrong Qiu

DOI: https://doi.org/10.1364/OL.511729

2024-01-01

Abstract:High-gain materials and high-quality structures are the two main conditions that determine the amplification performance of optical waveguides. However, it has been hard to balance each other, to date. In this work, we demonstrate breakthroughs in both glass optical gain and optical waveguide structures. We propose a secondary melting dehydration technique that prepares high-quality Er3+-Yb3+ co-doped phosphate glass with low absorption loss. Additionally, we propose a femtosecond laser direct-writing technique that allows controlling the cross section, size, and mode field of waveguides written in glass with high accuracy, leveraging submicron-resolution multi-scan direct-writing optical waveguide technology, which is beneficial for reducing insertion loss. As a proof of concept demonstration, we designed and fabricated two kinds of waveguides, namely, LP01- and LP11-mode waveguides in the Er3+-Yb3+ co-doped phosphate glass, enabling insertion loss as low as 0.9 dB for a waveguide length of 2 mm. Remarkably, we successfully achieved an optical amplification for both the waveguides with a net gain of >7 dB and a net-gain coefficient of >3.5 dB/mm, which is approximately one order of magnitude larger than that in the Er3+-Yb3+ co-doped phosphate glass fabricated by the traditional melt-quenching method. This will open new avenues toward the development of integrated photonic chips.
Toward a 10 Db Net-Gain Waveguide Amplifier in an Er3+-Yb3+ Co-Doped Phosphate Glass

Xiangyu Sun,Zhi Chen,Liaolin Zhang,Daoyuan Chen,Yuying Wang,Beibei Xu,Zhijun Ma,Giuseppe Barillaro,Lijing Zhong,Jianrong Qiu

DOI: https://doi.org/10.1364/ol.511729

IF: 3.6

2023-01-01

Optics Letters

Abstract:High-gain materials and high-quality structures are the two main conditions that determine the amplification performance of optical waveguides. However, it has been hard to balance each other, to date. In this work, we demonstrate breakthroughs in both glass optical gain and optical waveguide structures. We propose a secondary melting dehydration technique that prepares high-quality Er3+-Yb3+ co-doped phosphate glass with low absorption loss. Additionally, we propose a femtosecond laser direct-writing technique that allows controlling the cross section, size, and mode field of waveguides written in glass with high accuracy, leveraging submicron-resolution multi-scan direct-writing optical waveguide technology, which is beneficial for reducing insertion loss. As a proof of concept demonstration, we designed and fabricated two kinds of waveguides, namely, LP01- and LP11-mode waveguides in the Er3+-Yb3+ co-doped phosphate glass, enabling insertion loss as low as 0.9 dB for a waveguide length of 2 mm. Remarkably, we successfully achieved an optical amplification for both the waveguides with a net gain of >7 dB and a net-gain coefficient of >3.5 dB/mm, which is approximately one order of magnitude larger than that in the Er3+-Yb3+ co-doped phosphate glass fabricated by the traditional melt-quenching method. This will open new avenues toward the development of integrated photonic chips. (c) 2023 Optica Publishing Group
Synthesis and study of novel erbium-doped La2O3-Al2O3 glasses for on-chip waveguide amplifier

Chunxu Wang,Mingjie Zhang,Yuanzhi Chen,Yan Wang,Junchang Lu,Xiangxin Huang,Yuhang Wei,Lei Wan,Shuqiang Huang,Zhen Li,Zhenqiang Chen,Zhaohui Li

DOI: https://doi.org/10.1016/j.jallcom.2021.162915

IF: 6.2

2022-04-01

Journal of Alloys and Compounds

Abstract:Highly erbium-doped xEr2O3-44La2O3-(56-x)Al2O3 glasses are synthesized by an aerodynamic levitation (ADL) technique. The optimum erbium-doped concentration in 5Er2O3-44La2O3-51Al2O3 glass can reach ~1.61 × 1021 cm−3. All the fluorescence emission spectra of the glasses under different wavelength bands are measured. The results show the strongest emission intensity at communication band (C-band). The longest radiation lifetime in 4I13/2 → 4I15/2 transition is about ~5.23 ms. The Judd-Ofelt (J-O) parameters of 5Er2O3-44La2O3-51Al2O3 glass are also calculated to evaluate the potential of the glass as a substrate material for optical waveguide amplifier. Based on the parameters of the glass, We used MATLAB to write the gain simulation model of the waveguide amplifier, combined with the COMSOL software to simulate and optimize the waveguide geometry, and calculated the overall gain characteristic curves of optical waveguide amplifiers with different lengths are calculated theoretically. An internal net gain of up to 12.13 dB/cm in the C-band is obtained from the hybrid waveguide amplifier with 1 cm.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Recent Development of Glass-Based Integrated Optical Devices

Wang Minghua,Hao Yinlei,Li Xihua,Zhou Qiang,Jiang Xiaoqing,Yang Jianyi

DOI: https://doi.org/10.3969/j.issn.1673-1131.2007.02.002

2007-01-01

Abstract:A brief overview is given on the principle and the state-of-the-art of glass-based integrated optics.Then our recent effort on fabrication techniques of glass-based wavvguides and related optical components is presented,and the main issues currently we faced are discussed.
Recent development of ion-exchanged glass waveguide technology

Yinlei Hao,Minghua Wang,Xihua Li,Jianyi Yang,Xiaoqing Jiang,Qiang Zhou

DOI: https://doi.org/10.1109/AOE.2006.307327

2006-01-01

Abstract:A brief review is given on the physical mechanism and the state-of-the-art of glass-based integrated optic devices by ion-exchange technology, after which an comprehensive introduction is made on our recent research work conducted on glass-based waveguide devices manufacturing, including ion-exchange technology investigation, device configuration optimization, and novel devices development, Emphasis being put on development of glass based integrated optical splitter for optical communication networks application. In the last part, a prospect is given on glass based hybrid optical waveguide, which is regarded as a promising solution to low-cost, high-performance, multifunctional integrated optic devices, for it combines the advantages of glass waveguide and functionalities of another material.
Study on Er3+-Yb3+ co-doped La2O3–Al2O3 glasses for C-band optical waveguide amplifier with high luminous efficiency and low pump threshold

Mingjie Zhang,Junchang Lu,Yuanzhi Chen,Yuhang Wei,Yueqin Shao,Zhengkai Li,Fengkai Ma,Shuqiang Huang,Zhen Li,Zhenqiang Chen,Rongping Wang,Zhaohui Li

DOI: https://doi.org/10.1016/j.ceramint.2022.07.165

IF: 5.532

2022-11-01

Ceramics International

Abstract:Efficient planar optical waveguide amplifiers at C-band are critical to the development of silicon photonics. In order to overcome the problem of low utilization efficiency of 980 nm pump for erbium-based planar optical waveguide amplifiers, an Er3+-Yb3+ co-doped La2O3–Al2O3 glass material for optical waveguide amplifiers was developed in this paper. While maintaining a high Er3+ doping concentration (∼1021 cm−3), the utilization efficiency of the material for 980 nm pumping is improved, so that the pump threshold of the waveguide amplifier fabricated with this material is lowered. Moreover, up-conversion and down-conversion luminescence are also suppressed in the material, resulting in a significant increase in the luminescence intensity of the C-band. A simple ridge waveguide simulation suggests that waveguide amplifiers fabricated by this material are expected to surpass the highest net gain reported so far for erbium-based planar waveguide amplifiers.

materials science, ceramics
On-Chip Waveguide Amplifiers for Multi-Band Optical Communications: A Review and Challenge

Zhenshi Chen,Lei Wan,Shecheng Gao,Kun Zhu,Mingjie Zhang,Yan Li,Xiangxin Huang,Zhaohui Li

DOI: https://doi.org/10.1109/JLT.2022.3153447

IF: 4.7

2022-01-01

Journal of Lightwave Technology

Abstract:Erbium (Er)-doped fiber amplifier (EDFA) has achieved great success in modern optical communications for decades due to its outstanding gain performance in C-band. Nowadays, people are making efforts to make it monolithic integration due to the imperious demands from the advancement of high-performance and multi-function optoelectronic devices and chips. Except for the Er-doped waveguide amplifier, the other ion-doped on-chip waveguide amplifiers have also attracted much attention for multi-band optical communications, since they have own advantages in gain, bandwidth, selectivity of host materials, and integrability. Herein, we review the transmission characteristics of ion-doped on-chip waveguide amplifiers including gain and bandwidth, combining with the emission mechanisms and fabrication processes in applications of long-haul and short-reach optical communications. To facilitate the practical progress of the integrated waveguide amplifiers, from the perspective of gain medium, we also discuss the challenges and potential solutions for future technology roadmap. We expect that the bismuth (Bi)-doped waveguide amplifier would present impressive advantages in multi-band optical communications.
Er3+–Yb3+ co-doped glass waveguide amplifiers using ion exchange and field-assisted annealing

X.Z. Zhang,K. Liu,S.K. Mu,C.Z. Tan,D. Zhang,E.Y.B. Pun,D.M. Zhang

DOI: https://doi.org/10.1016/j.optcom.2006.07.037

IF: 2.4

2006-01-01

Optics Communications

Abstract:Er3+–Yb3+ co-doped waveguide amplifiers fabricated using thermal two-step ion-exchange are demonstrated. K+–Na+ ion-exchange process was first carried out in pure KNO3 molten bath, and then field-assisted annealing (FAA) was used to make the buried waveguides. The effective buried depth is estimated to be ∼3.4μm for the buried FAA waveguides. With the use of cut-back method, the fiber-to-guide coupling loss of ∼4.38dB, the waveguide loss of ∼2.27dB/cm, and Er3+ absorption loss ∼5.7dB were measured for a ∼1.24-cm-long waveguide. Peak relative gain of ∼7.0dB is obtained for a ∼1.24-cm-long waveguide. The potential for the fabrication of compact optical amplifiers operating in the range of 1520–1580nm is also demonstrated.
Characterization of Ion Exchange Erbium-Doped Silica Glass Amplifiers

郑杰,王鹏飞,徐迈,范希武,Righini G C

DOI: https://doi.org/10.3321/j.issn:0253-2239.2003.12.003

2003-01-01

Abstract:The growing interest for the use of integrated optical amplifiers in optical fiber telecom has led to deep search for better rare-earth-doped glassy materials. Some properties of a set of Er3+/Yb3+-doped silicate glass are reported. Planar and channel waveguides are fabricated by Ag+-Na+ ion exchange. Spectral measurement shows that the fluorescence emission peak for all the samples is observed at 1532 nm, with a full-width at half-maximum (FWHM) equal to 19 nm. Measurements of the lifetime of the metastable state (4I13/2) of Er3+ are performed upon excitation by laser pumps at 514.5 nm and 980 nm, and life time of the order of 7 ms is measured in most samples. The intensity of the up-conversion fluorescence in Er3+/Yb3+ co-doped glass is less than that in Er3+-doped one. 5 dB net gain at the wavelength of 1536 nm is obtained in a 3.5 cm long channel waveguide with 250 mW pump power at 980 nm and the FWHM is 14 nm.
Phosphate Glass Waveguide Amplifiers

Zhang Dan,Liu Ke,Z. Daming,C. Chuanhui,Zhang Xizhen,Zhang Haiming,Pan Yubin

2006-01-01

Abstract:An Er3+-Yb3+ co-doped phosphate glass waveguide for applications in optical amplifiers is studied.The optical gain at the wavelength of 1535nm is measured,and an 8.5dB relative gain in a 1.2cm device is observed when the waveguide is pumped with a 976nm laser with 130mW of power.In this case,the device shows strong green luminescence,and the intensity increases as the power of the pump laser increases.Also,upconversion from 2H11/2 and 4S3/2 levels is confirmed by using a photomultiplier and a monochromator.
High-order mode waveguide amplifier with high mode extinction ratio written in an Er3+-doped phosphate glass

Xiangyu Sun,YuYing Wang,Lijing Zhong,Daoyuan Chen,Beibei Xu,Zhijun Ma,Xiaofeng Liu,Giuseppe Barillaro,Zhi Chen,Jianrong Qiu

DOI: https://doi.org/10.1364/OE.481729

2023-02-13

Abstract:Inscription of fiber-compatible active waveguides in high-gain glass, followed by direct interconnection with few-mode fibers, is one of the most promising solutions for all-optical mode-division multiplexing. In this work, based on the femtosecond laser writing technique, we propose a general fabrication scheme for inscribing high-order mode waveguides in glass, by carefully tailoring the cross-section of the waveguides to match the mode intensity distribution via an improved multi-scan approach. Specifically, we design and fabricate two kinds of waveguides, namely, LP01-mode waveguide and LP11-mode waveguide in a highly Er3+-doped phosphate glass, enabling the insertion loss of the waveguides to be as low as 1.88 dB, and the mode extraction factor of the LP11-mode waveguide up to ∼24 dB. Importantly, we have successfully achieved optical amplification of the waveguides, with an on-off gain as high as 3.52 dB. This novel high-order mode waveguide amplifier has broad application prospects in monolithic on-chip integrated photonic light sources and optical interconnection with few-mode fiber and/or silicon-based waveguide.
Optical Gain and Upconversion in Er~(3+)-Yb~(3+) Co-Doped Phosphate Glass Waveguide Amplifiers

Zhang Dan,Liu Ke,Zhang Daming,Cheng Chuanhui,Zhang Xizhen,Zhang Haiming,Pan Yubin

DOI: https://doi.org/10.3321/j.issn:0253-4177.2006.10.031

2006-01-01

Chinese Journal of Semiconductors

Abstract:An Er~ 3+ -Yb~ 3+ co-doped phosphate glass waveguide for applications in optical amplifiers is studied.The optical gain at the wavelength of 1535nm is measured,and an 8.5dB relative gain in a 1.2cm device is observed when the waveguide is pumped with a 976nm laser with 130mW of power.In this case,the device shows strong green luminescence,and the intensity increases as the power of the pump laser increases.Also,upconversion from ~2H_ 11/2 and ~4S_ 3/2 levels is confirmed by using a photomultiplier and a monochromator.
Recent Progress in 1.4 Μm～1.7 Μm Broadband Light Amplification Materials

周博,肖志松,燕路,朱放,黄安平,王金良,许怀哲

DOI: https://doi.org/10.3969/j.issn.1002-2082.2008.04.026

2008-01-01

Journal of Applied Optics

Abstract:The broadband amplification is defined as the net amplified gain achieved in the whole lowest loss wavelength band 1.4 μm～1.7 μm of silica-based fibers.Efficient broadband light amplification materials can meet the needs of large information capacity and optical integration in communications.The materials for this application are mostly oxide-doped rare earth(RE) thin films,glasses and polymers.The former two materials are introduced in terms of band width,photoluminescence(PL) characteristic and PL mechanisms.The methods to improve the PL properties are discussed with the author′s previous results and experiences.It is concluded that there is a great potential for nano-structured RE co-doped materials.Finally,the prospect of the optical amplification is put forward.
Erbium Silicate Compound Optical Waveguide Amplifier and Laser [Invited]

Xingjun Wang,Peiqi Zhou,Yandong He,Zhiping Zhou

DOI: https://doi.org/10.1364/ome.8.002970

2018-01-01

Optical Materials Express

Abstract:In the process of information technology, as Moore's law becomes more and more close to the limit, the consensus to combine microelectronics and optoelectronics to develop silicon-based large-scale optoelectronic integration technology is inevitable. As the most important part of silicon photonic devices. a silicon-based light source still attracted great effort. In the traditional research, erbium-doped materials have played an important role in silicon-based light sources. Recent studies demonstrated that the erbium silicate compound had a high net gain attributable to a high erbium concentration that has no insolubility problem. This paper focuses on the theory, designs, simulations, preparation methods, process and device optimizations of the erbium silicate compound optical waveguide amplifier and laser. The erbium silicate compound materials with large optical gains can serve as potential candidates for future silicon-based scale-integrated light-source applications. (C) 2018 Optical Society of America under the terms of the OSA Open Access Publishing Agreement
A study of erbium-ytterbium-codoped polymer waveguide amplifier

DanDan Zhang,Daming Zhang,Xu Liang,Fei Wang,Donghui Guo

DOI: https://doi.org/10.1002/mop.26193

IF: 1.311

2011-01-01

Microwave and Optical Technology Letters

Abstract:In this article, organic/inorganic hybrid matrix doped with Er3+, Yb3+ nanoparticles was synthesized and used as the core material to fabricate the waveguide amplifier. The absorption and luminescence spectra of the material were characterized. An X-ray photoelectron spectroscopy analysis was performed to characterize the changes on the surface elemental composition of the material in the reactive ion etching processes. An embedded channel waveguides based on this material were demonstrated. Optical gains of 2.3 and 3.5 dB/cm at 1534 and 1550 nm wavelengths, respectively, were obtained in different dimensions of waveguides. (C) 2011 Wiley Periodicals, Inc. Microwave Opt Technol Lett 53: 2157-2160, 2011; View this article online at wileyonlinelibrary.com. DOI 10.1002/mop.26193
Erbium-doped Ga2O3 waveguide for optical amplification

Ruixue Liu,Zheng Zhang,Zhen Yang,Wei Wang,Kunlun Yan,Maozhuang Song,Rongping Wang

DOI: https://doi.org/10.1063/5.0168092

IF: 4

2023-10-09

Applied Physics Letters

Abstract:We prepared an Er3+-doped gallium oxide amorphous film using a radio frequency magnetron sputtering method and fabricated the waveguide using ultraviolet lithography and inductively coupled plasma etching to explore its optical amplification performance. In a 7 mm long waveguide, we achieved an on-chip gain of ∼4.7 dB at a pump power of 48.6 mW (∼16.9 dBm) and a signal power of 57.5 nW (∼−42.4 dBm). The preliminary results indicate the great potentials of an amorphous Ga2O3 film as a photonic material, especially in the application of an on-chip optical amplifier.

physics, applied
Approaching High Gain in Rare-earth-doped Waveguide Amplifiers:A Technological Review

Xu HAN,Jiaming LIU,Feng ZHANG,Anping HUANG,Zhisong XIAO

DOI: https://doi.org/10.11896/j.issn.1005-023X.2016.017.016

2016-01-01

Abstract:With the advantages in integration,miniaturization and economical efficiency,the rare-earth doped waveguide amplifier (RDWA)is developed as an amplifier of new generation.Two feasible ways to optimize RDWA are to improve luminous efficiency of rare-earth doped in the material as well as to reduce the loss of the amplifier. This optimization of RDWA requires more applicable materials,high performance waveguide structure and ultra-low loss materials.This paper reviews glass-based,polymer-based,silicon-based and low-loss material based RDWA,and pictured the prospects of practical applications and possible development of RDWA.
Rare Earth Ions Doped Optical Functional Glass and Application (Invited)

He Dongbing,Hu Lili,Chen Shubin,Tang Jingping,Wang Biao,Zhang Liyan,Wang Xin

DOI: https://doi.org/10.3788/irla20201081

2020-01-01

Infrared and Laser Engineering

Abstract:The luminescence and laser properties of rare earth are produced by the transition of 4f electrons between different energy levels. Due to its special properties, rare earth ions doped optical-functional glass have played important roles in high power laser system, whether as active or passive components. Nd3+, Er3+ doped phosphate laser glass, which have high rare earth ion doping concentration, preparation characteristics with large size and high uniformity, can be used in high energy laser as an important gain medium material; Volume Bragg grating based on Ce3+-doped Photo-Thermo-Refractive glass, is a multifunctional optical components in high power laser system, owing to its excellent wavelength and angular selectivity, high diffraction efficiency, high thermal stability and high damage threshold. In this paper the latest progress of Nd3+, Er3+ doped phosphate laser glass and Volume Bragg grating base on Ce3+-doped Photo-Thermo-Refractive glass were reported.
Optical and spectral parameters of Er3+ and Yb3+ co-doped phosphate glass for waveguide fabrication

Quan SHEN,Jingjing ZHANG,Ming LIU,Zhiqiang WANG,Xin ZHAO

2017-01-01

Abstract:Alkaline aluminum phosphate glasses were fabricated,and planar waveguide was obtained on Er3+/Yb3+ co-doped NMAP glass after submerging the glass sample into the KNO3 fused salt under 390 ℃ for 2 h.The effective diffusion coefficient was deduced to 0.11 μm2/min,indicating that the ion exchange process was achieved efficiently.According to the spectrum analysis,the full width at half maximum and maximum stimulated emission cross section of 4I13/2 →I15/2 energy level transition were 30 nm and 6.80 × 10-21 cm2.Results showed that the calculated theoretical gain could achieve 2.97 dB/cm when the ratio of Er3+ in 4I13/2 energy level reached to 80％.

Recent Progress in Erbium- Doped Optical Glass Waveguide Amplifiers

Er–Tm co-doped materials for on-chip ultra-broadband waveguide amplifier

Toward a10 dB net-gain waveguide amplifier in an Er3+-Yb3+ co-doped phosphate glass

Toward a 10 Db Net-Gain Waveguide Amplifier in an Er3+-Yb3+ Co-Doped Phosphate Glass

Synthesis and study of novel erbium-doped La2O3-Al2O3 glasses for on-chip waveguide amplifier

Recent Development of Glass-Based Integrated Optical Devices

Recent development of ion-exchanged glass waveguide technology

Study on Er3+-Yb3+ co-doped La2O3–Al2O3 glasses for C-band optical waveguide amplifier with high luminous efficiency and low pump threshold

On-Chip Waveguide Amplifiers for Multi-Band Optical Communications: A Review and Challenge

Er3+–Yb3+ co-doped glass waveguide amplifiers using ion exchange and field-assisted annealing

Characterization of Ion Exchange Erbium-Doped Silica Glass Amplifiers

Phosphate Glass Waveguide Amplifiers

High-order mode waveguide amplifier with high mode extinction ratio written in an Er3+-doped phosphate glass

Optical Gain and Upconversion in Er~(3+)-Yb~(3+) Co-Doped Phosphate Glass Waveguide Amplifiers

Recent Progress in 1.4 Μm～1.7 Μm Broadband Light Amplification Materials

Erbium Silicate Compound Optical Waveguide Amplifier and Laser [Invited]

A study of erbium-ytterbium-codoped polymer waveguide amplifier

Erbium-doped Ga2O3 waveguide for optical amplification

Approaching High Gain in Rare-earth-doped Waveguide Amplifiers:A Technological Review

Rare Earth Ions Doped Optical Functional Glass and Application (Invited)

Optical and spectral parameters of Er3+ and Yb3+ co-doped phosphate glass for waveguide fabrication