Abstract:We report on the influence of the dielectric/organic interface properties on the electrical characteristics of field-effect transistors based on Poly-phenylenevinylene derivatives. We observe a direct influence of the dielectric surface on the field-effect mobility as well as on the charge injection at the source electrode, despite the fact that we used a top contact transistor structure.We find that the presence of traps at the dielectric surface, decreases the hole mobility and increases the threshold voltages. By treating the silicon dioxide dielectric surface with gas phase molecules such as octadecyltrichlorosilane (OTS) and hexamethyldisilazane (HMDS) the hole mobility improves and the threshold voltage slightly increases.The effects of a dielectric polymer layer spin coated onto silicon dioxide substrates before deposition of the semiconductor polymer can be related to the density of the oxydryl groups (-OH), which are the most efficient traps for the charges flowing in the device. We use different polymer species such as polyvinylalchol (PVA), polymethylmetacrilate (PMMA) and a cyclotene derivative (B-staged bisbenzocyclobutene or BCB). The elimination of the -OH groups and of other traps, produces the same effect observed with HMDS coupled to a more pronounced enhancement of the threshold voltage, with the exception of PMMA. The electrical characteristics obtained with HMDS and PMMA polymer dielectrics are the highest reported to date for PPV-based field-effect transistors.We confirm that the purification of the active material is crucial to enhance the device performances and to achieve a better device to device reproducibility.We also investigated the effect of the dispersion of a phosphorescent dye into the active polymeric material. The electrical characteristics of OFETs with HMDS or PMMA dielectric with and without dye doping are compared.

Effect of Impurity Ions and Permanent Dipoles for Device Performance of Thin-Film Electroluminescent Diodes

Spontaneous And Reverse-Bias Induced Recovery Behavior In Organic Electroluminescent Diodes

Fluoride Interfaces Enhance the Performance of Perovskite Light-emitting Diodes

Recoverable Degradation Phenomena of Quantum Efficiency in Organic EL Devices

Improvement of Current-Voltage Characteristics in Organic Light Emitting Diodes by Application of Reversed-Bias Voltage

Short-Term Degradation Behaviors of Light Emitting Diodes Made of Polyurethane Derivative with Large Permanent Dipoles on the Side Chain

Influence Of The Dielectric And Of The Active Layer Doping On The Fet Mobility In Ppv-Based Devices

Suppressing Degradation of ITO Electrode for Electroluminescence Device by Transparent MoO3 Barrier Layer

Impact of surface polarization and ion accumulation on electroluminescence for methylammonium lead bromide light emitting diodes

Organic Electroluminescent Device Based on Balanced Carriers Injection and Transportation

Coulomb effect induced intrinsic degradation in OLED

Enhanced Performance of Inverted Perovskite Quantum Dot Light-Emitting Diode Using Electron Suppression Layer and Surface Morphology Control

Impurity Resonant State P-Doping Layer for High-Efficiency Nitride-Based Light-Emitting Diodes

Influence of Sensitizer on Organic Electroluminescence

Effect of Substitution of Crown Ether on the Luminescence Performances of PPV

High Luminance and Stability of Perovskite Quantum Dot Light-Emitting Diodes Via ZnBr2 Passivation and an Ultrathin Al2O3 Barrier with Improved Carrier Balance and Ion Diffusive Inhibition

The effect of dry etching condition on the performance of blue micro light-emitting diodes with reduced quantum confined Stark effect epitaxial layer

Dependence of the Performance of the Organic Electroluminescent Devices Upon the Deposition Rate of Organic Thin Films

Bilayer Electroluminescent Devices of Langmuir-Blodgett Films of Amphiphilic Complex Derivated from 8-Hydroxyquinoline Lanthanum

Enhancement In Brightness And Efficiency Of Organic Electroluminescent Device Using Novel N,N-Di(9-Ethylcarbaz-3-Yl)-3-Methylaniline As Hole Injecting And Transporting Material

Decoupling the Positive and Negative Aging Processes of Perovskite Light-Emitting Diodes Using a Thin Interlayer of Ionic Liquid.