Abstract:This study investigates the impact of thermomechanical processing route on the microstructural evolution, and mechanical properties (tensile strength, hardness and elastic plastic (J 1c ) fracture toughness) of the 7075-aluminum alloy. As received 7075 Al Alloy underwent for the solution heat treatment (SHT) followed by artificial aging and cold rolling (CR) process, respectively. Generally, it was observed that cold rolling of 7075 Al alloy is very challenging, but in this work 90 % cold rolling successfully achieved by optimizing the thermo-mechanical process. The novel heat treatment process for achieving the 90 % cold rolling reduction as follow: firstly, SHT was performed at 470°C for 8 hours(h), there after aging at 140°C for 21 h was performed. Characterization techniques like X-ray diffraction (XRD), optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) was employed to assess the microstructure and phase constituents. Elastic plastic (J 1c ) fracture toughness was studied well on SHT, peak aged and rolled sample. Additionally, Vickers hardness and tensile test were performed. Aging and Cold rolling treatment effectively enhanced tensile strength and hardness ascribed to formation of fine rod shape precipitates of η"(Mg 2 Zn 3 ) and formation of sub grains with localized strain accumulation, respectively Split diffraction spots with satellite pattern in long range ordering has also observed in selected area electron diffraction (SAED) pattern of η" attributable to stacking faults and periodic arrangement of precipitates, respectively, as a consequence of this 90 % cold rolling of 7075 Al alloy was accomplished. The maximum Vickers hardness, Tensile strength and Elastic plastic (J 1c ) fracture toughness values were achieved after SHT (470°C for 2 h), peak aged (PA) (140°C for 21 h) and 90 % cold rolling are 226 HV, 526 MPa and 344.54 kJ/m 2 , respectively.

Influence of Different Thermomechanical Processes on the Mechanical Properties and Microstructure of Al-Mg-Si-Cu Alloy Sheets

Effect of Alloying Elements and Processing Parameters on Microstructure and Properties of 1XXX Aluminium Alloys

Investigation of particles on the microstructure, texture and formability of Al–Mg-Si-Zn alloy for automotive body sheet

The Dependence of Final Microstructure, Texture Evolution and Mechanical Properties of Al–Mg–Si–Cu Alloy Sheets on the Intermediate Annealing

Tailoring the formability and planar anisotropy of Al-Mg-Si-Cu-Zn alloys via cross hot rolling and two-stage cold rolling

Effect of recrystallization annealing, solid solution and pre-aging intermediate treatment on microstructure and mechanical properties of Al-Mg-Si rolled sheet

Coordinated deformation mechanisms of high formability Al–Mg–Si–Cu–Zn–Fe alloys via coupling control of thermomechanical processes

Enhanced grain refinement and texture weakening in Al–Mg–Si alloy through a novel thermomechanical processing

Effect of Deformation on Precipitation and the Microstructure Evolution during Multistep Thermomechanical Processing of Al-Zn-Mg-Cu Alloy

Microstructure and mechanical properties of Al-Mg-Si alloy during solution heat treatment and forging integrated forming process

Effect of thermomechanical processing on mechanical properties and microstructural evolution of Al-Mg-Zn alloy

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

Comparative study on the formability and microstructure evolution of different tempered Al–Cu–Li alloy sheets during room and cryogenic temperature forming process

Influence of different rolling processes on the microstructures and mechanical properties of 6016 aluminum alloy

Microstructural Evolution and Mechanical Properties of Pure Aluminum upon Multi-Pass Caliber Rolling

Research on Alloy Design and Process Optimization of Al–Mg–Zn-Cu-Based Aluminum Alloy Sheets for Automobiles with Secured Formability and Bake-Hardenability

Effect of Deep-Cooling Rolling Deformation on the Microstructure and Mechanical Properties of an Al-4.5Cu-1.5Mg-0.6Mn-0.2Ti Alloy

Towards high mechanical performance Al–Cu–Mg–Fe–Ni alloy: influence of composition, solution treatment and aged process on microstructural evolution and mechanical properties

Enhanced formability of Al–Mg–Si–Zn alloy sheet via dislocation structure and texture during cold rolling

Effect of annealing treatment on the microstructure and mechanical properties of warm-rolled Mg–Zn–Gd–Ca–Mn alloys

Effect of Pretreatment and Cryogenic Temperatures on Mechanical Properties and Microstructure of Al-Cu-Li Alloy