Abstract:Integrated photonics requires high gain optical materials in the telecom wavelength range for optical amplifiers and coherent light sources. Erbium (Er) containing materials are ideal candidates due to the 1.5 μm emission from Er3+ ions. However, the Er density in typical Er-doped materials is less than 1020 cm–3, thus limiting the maximum optical gain to a few dB/cm, too small to be useful for integrated photonic applications. Er compounds could potentially solve this problem since they contain much higher Er3+ density. So far the existing Er compounds suffer from short lifetime and strong upconversion effects, mainly due to poor crystal qualities. Recently, we explore a new Er compound: erbium chloride silicate (ECS, Er3(SiO4)2Cl) in the form of nanowire, which facilitates the growth of high quality single crystal with relatively large Er3+ density (1.62 × 1022 cm–3). Previous optical results show that the high crystal quality of ECS material leads to a long lifetime up to 1 ms. The Er lifetime-density product was found to be the largest among all the Er containing materials. Pump-probe experiments demonstrated a 644 dB/cm signal enhancement and 30 dB/cm net gain per unit length from a single ECS wire. As a result, such high-gain ECS nanowires can be potentially fabricated into ultra-compact lasers. Even though a single ECS nanowire naturally serves as good waveguide, additional feedback mechanism is needed to form an ultra-compact laser. In this work, we demonstrate the direct fabrication of 1D photonic crystal (PhC) air hole array structure on a single ECS nanowire using focused ion beam (FIB). Transmission measurement shows polarization-dependent stop-band behavior. For transverse electric (TE) polarization, we observed stop-band suppression as much as 12 dB with a 9 μm long airholed structure. Through numerical simulation, we showed that Q-factor as high as 11000 can be achieved at 1.53 μm for a 1D PhC micro-cavity on an ECS nanowire. Such a high Q cavity combined with the high material gain of ECS nanowires provides an attractive solution for ultra-compact lasers, an important goal of this research.

Fabrication Of 1d Photonic Crystal On A Single Erbium Chloride Silicate Nanowire And Microcavity Laser Design

Fabrication of Optical Cavities with Femtosecond Laser Pulses

Microlaser based on a hybrid structure of a semiconductor nanowire and a silica microdisk cavity.

Fabrication of high-Q microresonators in dielectric materials using a femtosecond laser: Principle and applications

Femtosecond Laser Direct Writing of High-Q Microresonators in Glass and Crystals

Single Crystal Erbium Compound Nanowires As High Gain Material for On-Chip Light Source Applications

High-Q and High-Order Side-Coupled Air-Mode Nanobeam Photonic Crystal Cavities in Silicon

Photonic Crystal Laser on Thin Film Erbium-Doped Lithium Niobate

High- Q Photonic Crystal Cavity in a Single-Mode Silicon Ridge Waveguide

Fiber-Integrated Reversibly Wavelength-Tunable Nanowire Laser Based on Nanocavity Mode Coupling.

Optical Microfiber-Based Photonic Crystal Cavity

Femtosecond Laser Micro-Fabrication for Tailoring Photonic Crystals in Resins and Silica

On-chip Lithium Niobate Heterogeneous Photonic Crystal Nanocavity Laser

Fabrication of two dimensional high aspect ratio polymer photonic crystal laser

Photonic Crystal Cavities in Microfibers with Modest Finesse and Wavelength Scale Mode Volume

Design and Fabrication of Low-Refractive-index Polymeric Photonic Crystal Nanobeam Structures

Design and Simulation of Low-Threshold Miniaturized Single-Mode Nanowire Lasers Combined with a Photonic Crystal Microcavity and Asymmetric Distributed-Bragg-Reflector Mirrors

Photonic crystal formation on optical nanofibers using femtosecond laser ablation technique

Design of One-Dimensional Edge-Emitting Organic Semiconductor Photonic Crystal Lasers

Fabrication and Spectra-Measurement of High Q Photonic Crystal Cavity on Silicon Slabs

Dual-band Lasing from ZnO/CsPbBr3 Core/shell Microcavity