Abstract:Isothermal compression tests of 7A09 aluminum alloy were carried out on a Gleeble-1500 simulator at the deformation temperatures ranging from 633K to 733K, the strain rates ranging from 0.01s -1 to 10.0s -1, and the height reductions ranging from 40% to 85%. Several modeling approaches, including the flow stress-strain curves, the kinetic analysis, the constitutive model and the processing maps, are used to characterize the deformation behavior in the isothermal compression of 7A09 aluminum alloy in this paper. The experimental results show that the flow stress in the isothermal compression of 7A09 alloy is significantly sensitive to the strain, the strain rate and the deformation temperature. The flow stress decreases with the increasing of deformation temperature due to the dissolution of intermetallic precipitates into Al matrix and the occurrence of selective DRX at higher deformation temperatures. And, it increases noticeably with the increasing of strain rate because of the increase in the rate of dislocation generation. The apparent activation energy for deformation (Q) in the isothermal compression of 7A09 aluminum alloy varies slightly with the strain. The Q-values are about from 136.61kJmol -1 to 143.31kJmol -1 which is close to that self diffusion in pure aluminum. The constitutive model in the isothermal compression of 7A09 aluminum alloy is developed using the Zener-Hollomon parameter in the exponent-type equation. The maximum relative error and minimum relative error between the calculated and the experimental flow stress are 6.67% and 0.07%, respectively. Finally, the processing maps at different strains with microstructural examination are established in the isothermal compression of 7A09 aluminum alloy. It is concluded that the effect of strain on the processing maps is significant. The peak efficiency of power dissipation at a strain of 0.7 is about 0.34 occurring at a deformation temperature of 713K and strain rate of 0.01s -1, which is correspondent to an optimal deformation condition of 7A09 aluminum alloy. © 2011 Elsevier B.V.

Effect of Process Parameters on Mechanical Behavior of Semi-solid Al-4Cu-Mg Alloy

Deformation Behavior and Microstructural Evolution During the Semi-Solid Compression of Al–4Cu–Mg Alloy

Effect of the process parameters on microstructure of the semisolid Al-4Cu-Mg alloy in the isothermal compression process

Deformation and Microstructure Characterization During Semi-Solid Extrusion of Al-4cu-Mg Alloy

Experimental Investigation and Modelling of Microstructural Variables of Al–4Cu–Mg Alloy

Deformation Behavior of the Semi-solid LY11 Alloy

Effects of Process Parameters on the Microstructure and Hardness of Semi-Solid AlSi9Mg Aluminum Alloy Prepared by RAP Process

Deformation Characteristics and Constitutive Equations for the Semi-Solid Isothermal Compression of Cold Radial Forged 6063 Aluminium Alloy

The deformation behavior and processing maps in the isothermal compression of 7A09 aluminum alloy

Compression Deformation of Semi-solid LY11 Alloy

Influence of Soaking Time and Loading Rate on Semi-solid Compression of Porous Al-4Cu-Mg Alloy

Microstructural Characteristic of Aluminium Alloy in the Semisolid State

Microscopic Characterization of Semi-Solid Aluminium Alloys

Research on the Constitutive Equation of 6061 Aluminum Alloys in the Hot Compressive Deformation

Effect of Processing Parameters on Microstructure and Mechanical Properties in High Temperature Deformation of Ti-6Al-4V Alloy

Hot Deformation Behavior and Microstructure Characterization of an Al-Cu-Li-Mg-Ag Alloy

Microscopic Observation of Cold-Deformed Al–4Cu–Mg Alloy Samples after Semi-Solid Heat Treatments

Effects of pre-deformation on microstructure and mechanical properties of semi-solid 7075 alloy

Mechanical Behavior of 7A04 Alloy in Semisolid Isothermal Compression

Effects of Deformation Temperature and Rate on Compressive Deformation Behaviour of Y112 Die Cast Aluminum Alloy in Semi-Solid State

Deformation Behavior and Constitutive Equation Coupled the Grain Size of Semi-Solid Aluminum Alloy