Particle Clustering During Pearl Chain Formation in A Conductive-Island Based Dielectrophoretic Assembly System

Haitao Ding,Weiyu Liu,Yucheng Ding,Jinyou Shao,Liangliang Zhang,Peichang Liu,Hongzhong Liu

DOI: https://doi.org/10.1039/c4ra10721g

IF: 4.036

2015-01-01

RSC Advances

Abstract:Particle clustering during pearl chain formation in a conductive-island based dielectrophoretic assembly system.

What problem does this paper attempt to address?

Electrode-Rail Dielectrophoretic Assembly Effect: Formation of Single Curvilinear Particle-Chains on Spiral Microelectrodes

Xiaolu Zhu,Zhiqiang Gao,Zhifeng Yin,Zhonghua Ni

DOI: https://doi.org/10.1007/s10404-010-0600-9

2010-01-01

Microfluidics and Nanofluidics

Abstract:An electrode-rail dielectrophoretic (DEP) assembly effect for microparticle pearl-chain formation is reported. Under this assembly effect, single curvilinear particle chains are formed along spiral strip electrodes in a dielectrophoretic microfluidic device actuated by alternating signals. Moreover, the snaking traveling movement of the entire individual curving pearl chain along the spiral electrode is also observed. The formation of single curvilinear pearl chain could be mainly interpreted by the specific distribution of the electric field above the spiral microelectrode array. Further, the inter-attracting DEP force between neighboring particles in pearl chains is generated when the originally uniform electric field is strongly perturbed due to the existence of the particles themselves. The entire individual pearl chain's movement along the spiral strip electrode could be rationalized by the non-ignorable ohmic resistance distribution along the strip electrodes, which leads to the non-uniformity of field strength and DEP force along the spiral elongation direction.
Effect of Island Shape on Dielectrophoretic Assembly of Metal Nanoparticle Chains in a Conductive-Island-based Microelectrode System

Haitao Ding,Jinyou Shao,Yucheng Ding,Weiyu Liu,Xiangming Li,Hongmiao Tian,Yaopei Zhou

DOI: https://doi.org/10.1016/j.apsusc.2014.12.184

IF: 6.7

2015-01-01

Applied Surface Science

Abstract:The electrical conduction quality of an electric circuit connection formed by dielectrophoretic (DEP)assembled metal nanoparticle wires between small conductive elements plays a significant role in electronic devices. One of the major challenges for improving the electrical conductance of nanowires is optimizing their geometric morphology. So far, the electrical conduction quality has been enhanced by optimizing the AC frequency and conductivity of nanoparticle suspensions. Herein, the effect of the conductive island shapes on the dynamic process occurring in a DEP assembly of 10 nm gold nanoparticles was investigated in a conductive-island-based microelectrode system. The nanoparticle wires between the microelectrodes were assembled in situ from colloidal suspensions. The wires were grown in a much straighter route by increasing the geometric angle of the conductive-island tip. To validate the experiments, the effects of mutual DEP interactions and electrothermally induced fluid flow on the dynamic behavior of particle motion for different island geometric configurations in the conductive-island-based microelectrode system were determined by numerical simulations. The simulation results are consistent with those of experiments. This indicates that different conductive island shapes change the distribution of DEP force and increase the electrothermally induced fluid flow to different extents in the vicinity, leading to different morphologies of DEP-assembled nanoparticle wires. (C) 2015 Elsevier B.V. All rights reserved.
Influence of induced-charge electrokinetic phenomena on the dielectrophoretic assembly of gold nanoparticles in a conductive-island-based microelectrode system.

Haitao Ding,Weiyu Liu,Jinyou Shao,Yucheng Ding,Liangliang Zhang,Jiqiang Niu

DOI: https://doi.org/10.1021/la402060g

IF: 3.9

2013-01-01

Langmuir

Abstract:Metal nanoparticles in a liquid suspension can be assembled dielectrophoretically (DEP) into nanoparticle chains, which can serve as electrical functional microwires connecting isolated and conductive elements to an electrode pair, as used in wet electronics, bioelectronics, and biochemical sensors. The frequency-dependent morphology of these nanoparticle chains assembled between an electrode pair has even been attributed to the decreasing magnitude of alternating current electroosmosis (ACEO) flow velocity with driving frequency. For instance, highly oriented nanoparticle nanowires can be generated by DEP assembly only at a high frequency, which induces a negligible small ACEO above the electrode surface, corresponding to fewer nanoparticles transported to the assembly region. In this study, attention is focused on the formation of nanoparticle chains in a conductive-island-based microelectrode system. It is worth noting that the intrusion of an island entity can bring about further double-layer polarization and induced charge electroosmosis flow (ICEO) around this conductive object, which exerts a significant influence on DEP assembly. In our experiments, the ends of nanoparticle chains are always extended onto the metal surfaces at 50 kHz, and their central parts become slender at 150 kHz. Meanwhile, wire-shaped particle clusters aligned along the direction of local field lines are more densely distributed at the island rims than that growing from the electrode edges. Consequently, a series of numerical modeling based on the theory of induced charge electrokinetic phenomena are introduced to account for these regular experimental results, including the double-layer charging effect at the metal/electrolyte interface, ACEO, ICEO, and electrothermal flow. Mutual DEP is also treated as an important factor affecting DEP behavior when neighboring particles are approaching one another. The results from the theoretical study are in good agreement with the experimental observations.
Ac Electric Field Induced Dielectrophoretic Assembly Behavior of Gold Nanoparticles in A Wide Frequency Range

Weiyu Liu,Chunhui Wang,Haitao Ding,Jinyou Shao,Yucheng Ding

DOI: https://doi.org/10.1016/j.apsusc.2016.02.118

IF: 6.7

2016-01-01

Applied Surface Science

Abstract:In this work, we focus on frequency-dependence of pearl chain formations (PCF) of gold nanoparticles driven by AC dielectrophoresis (DEP), especially in a low field-frequency range, where induced double-layer charging effect at ideally polarizable surfaces on particle DEP behavior and surrounding liquid motion need not be negligible. As field frequency varies, grown features of DEP assembly structures ranging from low-frequency non-bridged gap to high-frequency single gold nanoparticle-made nanowires bridging the electrodes are demonstrated experimentally. Specifically, at 10 kHz, a kind of novel channel-like structure with parallel opposing banks is formed at the center of interelectrode gap. In stark contrast, at 1 MHz, thin PCF with diameter of 100 nm is created along the shortest distance of the isolation spacing. Moreover, a particular conductive path of nanoparticle chains is produced at 1 MHz in a DEP device embedded with multiple floating electrodes. A theoretical framework taking into account field-induced double-layer polarization at both the particle/electrolyte and electrode/electrolyte interface is developed to correlate these experimental observations with induced-charge electrokinetic (ICEK) phenomenon. And a RC circuit model is helpful in accounting for the formation of this particular non bridged channel-like structure induced by a low-frequency AC voltage. As compared to thin PCF formed at high field frequency that effectively short circuits the electrode pair, though it is difficult for complete PCF bridging to occur at low frequency, the non-bridged conducting microstructure has potential to further miniaturize the size of electrode gap fabricated by standard micromachining process and may find useful application in biochemical sensing. (C) 2016 Elsevier B.V. All rights reserved.
A Full-Scale Computational Study on the Electrodynamics of a Rigid Particle in an Optically Induced Dielectrophoresis Chip

Liuyong Shi,Xiaoming Shi,Teng Zhou,Zhenyu Liu,Zhiyuan Liu,Sangwoo Joo

DOI: https://doi.org/10.1142/s0217984920502334

2020-01-01

Modern Physics Letters B

Abstract:A transient continuum model of the ODEP chip containing single circular particle inside is constructed based on multi-physical field coupling. The dielectrophoresis force and liquid viscous resistance acting on particle are calculated by employing the full Maxwell stress tensor. The coupled flow field, electric field and particle are solved by the arbitrary Lagrange–Euler (ALE) method simultaneously. The throughout dynamic process of particle in the ODEP chip is demonstrated, and the effect of several critical parameters on particle electrodynamics is illuminated. The additional disturbing effect of the photoconductive layer on the electric field as well as the micro-channel wall on the flow field is presented to clarify the particle motion in the vertical direction. The results in this study provide a detailed understanding of the particle dynamics in the ODEP chip.
Facile Large-Scale Alignment and Assembly of Conductive Micro/nano Particles by Combining Both Flow Shear and Electrostatic Interaction

Jun Cai,Xinghao Li,Liang Ma,Yonggang Jiang,Deyuan Zhang

DOI: https://doi.org/10.1016/j.compscitech.2018.12.018

IF: 9.1

2019-01-01

Composites Science and Technology

Abstract:We introduce a facile approach to align various conductive micro/nano particles in a large area using both flow shear and electrostatic interaction. The complicated three-dimensional (3D) microcoils are chosen to investigate the assembly behavior and effectiveness of the multi-physical field induced alignment in polydimethylsiloxane (PDMS) pre-polymer; and the forcing mechanism and motion behavior of the microcoils are also analyzed: the flow shear could orient the major axis of microcoils, and then the electrostatic interaction between these oriented microcoils results in their self-assembly into chains. Besides, the processing parameters are also optimized, including the gap between the polyethylene terephthalate (PET) plates of similar to 100 mu m, the shearing speed of similar to 40 mm/s, PET plate voltage of similar to 20 kV, and microcoil weight fraction of similar to 2%. And the order parameter S could reach up to similar to 0.96 and more than similar to 70% of the particles were assembled into a chain-like structure. Furthermore, we also demonstrate the universality of this method to other conductive micro/nano particles' assembly, including silver-coated glass spheres, carbon nanotubes (CNTs), and graphene. This approach may pave the way for the large-scale fabrication of functional composites based on well-ordered conductive micro/nano particles.
Dielectrophoretic Assembly and Separation of Particles and Cells in Continuous Flow

Xiaoming Chen,Shun Liu,Mo Shen,Ziwei Gao,Sheng Hu,Yong Zhao

DOI: https://doi.org/10.1039/d3ay00666b

IF: 3.1

2023-08-02

Analytical Methods

Abstract:Dielectrophoretic (DEP) separation has been recognized as a practical tool in the separation of cells and particles for clinical diagnosis, pharmaceutical industry and environmental monitoring. Assembly of particles and cells under DEP force is a common phenomenon and has an influence on their separation but has not been understood fully. Encouraged by these aspects, we developed a microfluidic device with bipolar electrode array to investigate the assembly and separation of particles and cells at a large scale. Firstly, we studied the assembly and evolution mechanisms of particles of one types under AC electric field. Then, we investigated the interaction and assembly of multiple particles with dissimilar properties under DEP force. Depending on the development of microfluidic device, we visualize the assembly process of yeast cells at the electrode rims and of polystyrene particles at the channel centers, and explore influence of pearl chain formation on their separation. With increasing flow velocity from 288 to 720 L/h, purity of PS5 particles surpasses 94.9%. Furthermore, we studied DEP response of Scenedesmus sp. and C. vulgaris, and explored the influence of cell chains on the isolation of C. vulgaris. Purity of Scenedesmus sp. and C. vulgaris witnessed a decrease from 95.7% to 90.8% when flow rate increases from 288 to 864 L/h. Finally, we investigated extension of electric field under chains of Oocystis sp. at the electrode rims by studying chain formation and capture of C. vulgaris, and study its effect on cell chain length, recovered cell purity and cell concentration. When chains of Oocystis sp. were formed, the purity of C. vulgaris kept unchanged and the concentration decreased from 2793 cells/L to 2039 cells/ L. This work demonstrates continuous DEP-baed assembly and separation of particles and cells, which facilitates high-efficiency isolation of targeted cells.

spectroscopy,chemistry, analytical,food science & technology
Optical assembly of multi-particle arrays by opto-hydrodynamic binding of microparticles close to a one-dimensional chain of magnetic microparticles

Xian-Feng Zhang,Chun Meng,Wen Bai,Meng Shao,Feng Ji,Min-Cheng Zhong

DOI: https://doi.org/10.1063/5.0191898

IF: 1.6

2024-04-01

Review of Scientific Instruments

Abstract:Two-dimensional materials possess a large number of interesting and important properties. Various methods have been developed to assemble two-dimensional aggregates. Assembly of colloidal particles can be achieved with laser-heating-induced thermal convective flow. In this paper, an opto-hydrodynamic binding method is proposed to assemble colloidal particles dispersed in a solution into multilayer structures. First, we use polystyrene (PS) microspheres to study the feasibility and characteristics of the assembly method. PS microspheres and monodispersed magnetic silica microspheres (SLEs) are dispersed in a solution to form a binary mixture system. Under the action of an external uniform magnetic field, SLEs in the solution form chains. An SLE chain is heated by a laser beam. Due to the photothermal effect, the SLE chain is heated to produce a thermal gradient, resulting in thermal convection. The thermal convection drives the PS beads to move toward the heated SLE chain and finally stably assemble into multilayer aggregates on both sides of the SLE chain. The laser power affects the speed and result of the assembly. When the laser power is constant, the degree of constraint of the PS microbeads in different layers is also different. At the same time, this method can also assemble the biological cells, and the spacing of different layers of cells can be changed by changing the electrolyte concentration of the solution. Our work provides an approach to assembling colloidal particles and cells, which has a potential application in the analysis of the collective dynamics of microparticles and microbes.

instruments & instrumentation,physics, applied
Multidomain Oriented Particle Chains Based on Spatial Electric Field and Their Optical Application.

Yajun Zhang,Weitao Jiang,Tongkai Gu,Jie Han,Biao Lei,Lanlan Wang,Hongzhong Liu,Lei Yin,Bangdao Chen,Yongsheng Shi

DOI: https://doi.org/10.1021/acs.langmuir.0c02021

IF: 3.9

2020-01-01

Langmuir

Abstract:The manipulation technology of particles is significant in drug screening, disease detection and treatment, etc. Here, we reported the multidomain oriented particle chains based on a spatial electric field and their optical application. According to the differences in the dielectric behavior of particles, the preparation of multidomain oriented particle chains in the gel was successfully realized by using the dielectrophoretic force and electroosmotic rotation. This provides a new idea for manufacturing multistructure, multilayer, and multifunctional intelligent response materials. In addition, the factors affecting the alignment height of the particles in the gel were discussed, which was the basis for the preparation of bilayer particle chains. As an example of structural hierarchy, particle assembly has broad application prospects in optoelectronic devices and soft robots.
Self-Assembly From The Branch Pattern To Parallel Wire Array In Electrodeposition

mingzhe zhang,guihong zuo,zhaocun zong,haiyong chen,zhi he,chunming yang,dongmei li,guangtian zou

DOI: https://doi.org/10.1063/1.2203956

IF: 4

2006-01-01

Applied Physics Letters

Abstract:We report a self-organized copper electrodeposition without imposed templates and induced additives. The deposit morphology on the silicon substrate varies from a branch to a parallel pattern by changing the applied voltage. We suggest that there are two essential factors for the formation of such kind of copper wire arrays. One is a proper electric potential distribution near the tip of the copper wire which dictates the direction of the solute transport. The other one is that the cathode overpotential and the equilibrium potential of reaction should remain unchanged at the growing interface.
Template-Mediated Assembly Of Fept L1(0) Clusters Under External Magnetic Field

y c sui,wenhsing liu,l p yue,x z li,jizhong zhou,ralph skomski,d j sellmyer

DOI: https://doi.org/10.1063/1.1846592

IF: 2.877

2005-01-01

Journal of Applied Physics

Abstract:FePt L1(0)-structured clusters were synthesized by hydrogen reduction of Fe(NO3)(3).9H(2)O and H2PtCl6 (.) 6H(2)O mixtures within the pores of alumina. They were released by dissolving the alumina matrix and capped with organic surfactants. After a series of chemical treatments, clusters with an average diameter of about 11 nm were precipitated. The clusters were drop casted onto ordered nanoporous arrays. Clusters reaching the bottom of the pores formed an ordered magnetic array. The corresponding magnetic film exhibits distinct anisotropic behavior caused by the external magnetic field. (c) 2005 American Institute of Physics.
Conducting Nanopearl Chains Based on the Dmit Salt

GL Cui,W Xu,CW Guo,XW Xiao,H Xu,DQ Zhang,L Jiang,DB Zhu

DOI: https://doi.org/10.1021/jp048195a

2004-01-01

Abstract:Nanowire arrays of crystalline [(CH3)(4)N][Ni(dmit)(2)](2) have been fabricated by a galvanostatic electrochemical deposition method using anodic aluminum oxide as the template. A nanopearl chain structure associated with the oscillation of the voltage during the electrochemical deposition process was investigated, These nanowire arrays are highly textured as determined by XRD. The preliminary results show that the conductivities of the nanowires are in the semiconductor range.
A Novel Conductive Particle Dispersing Method via EHDA for POB-COG Packaging

Zhengyu Ba,X. Yuan,Lei Jia,Xinjun Sheng,Zhenhua Xiong,Han Ding

DOI: https://doi.org/10.1007/978-3-642-40849-6_39

2013-01-01

Abstract:With the continuous evolving of Liquid Crystal Display (LCD) panels and Integrate Circuits, conventional Anisotropic Conductive Film (ACF) has confronted with two paradoxical requirements: higher conductive particle density, while avoid serious aggregation. To solve this problem, a wafer level pretreatment technique, Particle on Bumps (POB), was proposed to renovate the usual Chip on Glass (COG) technology. Although we have demonstrated its feasibility and reliability, a fundamental route towards fully accomplishing the POB technique still needs to be paved out, that is the dispersing of conductive particles. Herein we introduced the method of Electrohydrodynamic Atomization (EHDA). EHDA is a technique which ultra-fine droplets can be induced due to electrical force. We build up a prototype apparatus for particle dispersing. With the help of high speed camera, we are able to verify certain behaviors and characteristics of different modes during the EHDA process. The deposition patterns generated under different spraying modes are observed and compared; the stable cone jet mode is therefore chosen as the operational state during our following deposition process. We investigate the connections between onset voltage and relevant spray parameters to optimize our EHDA configurations. By implementing the particle dispersing experiment via stable cone jet EHDA, we successfully obtained a pattern with high densely and uniformly distributed particles.
Numerical study of interactive motion of dielectrophoretic particles

chuanchuan xie,bo chen,chiuon ng,xinping zhou,jiankang wu

DOI: https://doi.org/10.1016/j.euromechflu.2014.08.007

IF: 2.598

2015-01-01

European Journal of Mechanics - B/Fluids

Abstract:Dielectrophoresis is one of the popular ways to manipulate bio-particles. In this work, numerical simulations of two-dimensional interactive motion of multiple dielectrophoretic particles in an electrolyte subjected to a uniform DC electric field are performed. The dielectrophoretic forces on particles are calculated by an integral of the Maxwell Stress Tensor (MST) on both sides of the particle surfaces. It is shown that behaviors of interactive motion of dielectrophoretic particles are strongly affected by the difference in permittivity between the particles and the electrolyte. Similar particles (all positive or negative electrophoresis) will finally form a chain parallel to the electric field, whereas dissimilar particles (mixed positive and negative electrophoresis) will form a chain that is perpendicular to the electric field. The particle velocity and time behavior of interactive motion are investigated. The key findings are as follows: as the ratio (εp:εf) increases, the chain-formation time decreases for a P–P particle chain, but increases for an N–N particle chain. The chain-formation time will decrease with increase of the particle size ratio amax:amin for a three-particle chain with different particle sizes.
Self-templating Growth of Copper Nanopearl-Chain Arrays in Electrodeposition

Yu-Yan Weng,Bo Zhang,Shao-Jie Fu,Mu Wang,Ru-Wen Peng,Guo-Bin Ma,Da-Jun Shu,Nai-Ben Ming

DOI: https://doi.org/10.1103/physreve.81.051607

IF: 2.707

2010-01-01

Physical Review E

Abstract:We report here a unique in-plane self-templating electrochemical growth of arrays of copper nanopearl chains from an ultrathin layer of CuSO4 electrolyte. Scanning electron microscopy indicates that the electrodeposit filaments form equally spaced bundles, which consist of long, straight, pearl-chain-like copper filaments with corrugated periodic structure. The bundle separation can be tuned by changing the applied electric current in electrodeposition. Experiments show that the periodic morphology on the nanopearl chain corresponds to the periodic distribution of copper and cuprous oxide. The mechanism for the bundle formation is discussed.
Massive Electro-Microfluidic Particle Assembly Patterns in Droplet Array for Information Encoding

Haoqiang Feng,Shitao Shen,Mingliang Jin,Mengjie Xiao,Mengjun Liu,Qilin Zhang,Hongwei Jiang,Zichuan Yi,WenShuai Wu,Guofu Zhou,Lingling Shui

DOI: https://doi.org/10.1002/smll.202405161

IF: 13.3

2024-09-06

Small

Abstract:The assembly of colloidal particles into micro-patterns is essential in optics, informatics, and microelectronics. However, it is still a challenge to achieve quick, reversible, and precise assembly patterns within micro-scale spaces like droplets. Hereby, a method is presented that utilizes in-plane dielectrophoresis to precisely manipulate particle assemblies within microscale droplets. The electro-microfluidic particle assembly platform, equipped with ingenious electrode designs, enables the formation of diverse micro-patterns within a droplet array. The tunability, similarity, stability, and reversibility of this platform are demonstrated. The ability to assemble letters, numbers, and Morse code patterns within the droplet array underscores its potential for information encoding. Furthermore, using an example with four addressing electrodes beneath a droplet, 16 distinct pieces of information through electrical stimuli is successfully encoded. This unique capability facilitates the construction of a dynamic electronic token, indicating promising applications in anti-counterfeiting technologies.
Dissipative particle dynamics simulation of self-assembly of phosphorylcholine-containing poly(L-lactide)

Zhigao Wang,Yuanwei Chen,Jiehua Li,Xianglin Luo,Hong Tan

DOI: https://doi.org/10.1166/jctn.2011.1900

2011-01-01

Journal of Computational and Theoretical Nanoscience

Abstract:Using dissipative particle dynamics (DPD) approach, we study the self-assembly behaviors of phosphorylcholine-containing poly(L-lactide) (PLLA-PC-PLLA) at the microscopic level. Their evolution of aggregate morphologies and internal distribution are observed. Spherical, cylindrical and lamellar structures are obtained at various concentrations. Additionally, their self-assembly morphologies can also be regulated by the PLA chain length, and short PLA chains facilitate the formation of bilayer structure. Our simulation results agree very well with recent experiments and are consistent with theoretical observations of other kinds of phospholipids, which is useful for the future rational design of bio-inspired materials with tailored properties.
Reconfigurable Assembly of Planar Colloidal Molecules via Chemical Reaction and Electric Polarization

Xi Chen,Xianghong Liu,Mohd Yasir Khan,Zuyao Yan,Dezhou Cao,Shifang Duan,Lingshan Fu,Wei Wang

DOI: https://doi.org/10.34133/research.0490

2024-01-30

Abstract:Colloidal molecules, ordered structures assembled from micro- and nanoparticles, serve as a valuable model for understanding the behavior of real molecules and for constructing materials with tunable properties. In this work, we introduce a universal strategy for assembling colloidal molecules consisting of a central active particle surrounded by several passive particles as ligands. During the assembly process, active particles attract the surrounding passive particles through phoresis and osmosis resulting from the chemical reactions on the surface of the active particles, while passive particles repel each other due to the electric polarization induced by an alternating current (AC) electric field. By carefully selecting particles of varying structures and sizes, we have assembled colloidal molecules of symmetric and asymmetric dimers, trimers, and multimers. Furthermore, the coordination number of these colloidal molecules can be regulated in real time and in situ by tuning the interaction forces between the constituent particles. Brownian dynamics simulations reproduced the formation of the colloidal molecules and validated that the self-assembly arises from chemically induced attraction and electrical dipolar repulsion. This strategy for reconfigurable colloidal assemblies poses the potential for designing adaptive micro-nanomachines.
Particle aggregation by positive dielectrophoresis

Charles Osarinmwian

DOI: https://doi.org/10.48550/arXiv.1312.1570

2013-12-05

Abstract:Particle aggregates are formed with viable yeast cells (Saccharomyces cerevisiae) and bacterial cells (Escherichia coli and Micrococcus luteus), and are assembled in an interdigitated-castelled microelectrode using positive dielectrophoresis with an alternating current sinusoidal voltage of 2-20 V peak-peak at 1 MHz. The height of S. cerevisiae aggregates are increased by the addition of the ampholytes N-[2-hydroxyethyl] piperazine-n'-[2-ethanesulfonic acid] (HEPES) or e-aminocaproic acid (EACA) due to the resulting rise in permittivity of the aqueous solution. The mean height of S. cerevisiae aggregates in the presence of 1 M HEPES was 25.7 % higher than achieved in an ampholyte-free solution. Based on the results obtained, a next-generation triangular grooved microelectrode is proposed as an alternative to the interdigitated-castelled microelectrode. This innovation could mark a paradigm shift from aggregating particles at specific regions of high electric strength (e.g. electrode edge) towards a layer by layer aggregation of particles along a microelectrode.

Soft Condensed Matter
Sorting of heterogeneous colloids by AC-dielectrophoretic forces in a microfluidic chip with asymmetric orifices

Kai Zhao,Minghan Hu,Carolina van Baalen,Laura Alvarez,Lucio Isa

DOI: https://doi.org/10.1016/j.jcis.2022.12.108

IF: 9.9

2022-12-26

Journal of Colloid and Interface Science

Abstract:Hypothesis The synthesis of compositionally heterogeneous particles is central to the development of complex colloidal units for self-assembly and self-propulsion. Yet, as the complexity of particles grows, synthesis becomes more prone to "errors". We hypothesize that alternating-current dielectrophoretic forces can efficiently sort Janus particles, as a function of patch size and material, and colloidal dumbbells by size. Experiments We prepared Janus particles with different patch size and material by physical vapor deposition and colloidal dumbbells via capillarity-assisted particle assembly. We then performed sorting experiments in a microfluidic chip comprising electrodes with asymmetric orifices, specifically exploiting the dielectric contrast between different portions of the particles or their size difference to steer them towards different outlets. Findings We calculated that the DEP force for Janus particles may switch from positive to negative as a function of composition at a critical AC frequency, thus enabling sorting different particles crossing the electrodes' region. The predictions are confirmed by optical microscopy experiments. We also show that intact and "broken" dumbbells can be simply separated as they experience different DEP forces. The integration of multiple asymmetric orifices leads a larger zone with high field gradient to increase separation efficiency and makes it a promising tool to select precise particle populations, isolating fractions with narrowly distributed characteristics.

chemistry, physical

Particle Clustering During Pearl Chain Formation in A Conductive-Island Based Dielectrophoretic Assembly System

Electrode-Rail Dielectrophoretic Assembly Effect: Formation of Single Curvilinear Particle-Chains on Spiral Microelectrodes

Effect of Island Shape on Dielectrophoretic Assembly of Metal Nanoparticle Chains in a Conductive-Island-based Microelectrode System

Influence of induced-charge electrokinetic phenomena on the dielectrophoretic assembly of gold nanoparticles in a conductive-island-based microelectrode system.

Ac Electric Field Induced Dielectrophoretic Assembly Behavior of Gold Nanoparticles in A Wide Frequency Range

A Full-Scale Computational Study on the Electrodynamics of a Rigid Particle in an Optically Induced Dielectrophoresis Chip

Facile Large-Scale Alignment and Assembly of Conductive Micro/nano Particles by Combining Both Flow Shear and Electrostatic Interaction

Dielectrophoretic Assembly and Separation of Particles and Cells in Continuous Flow

Optical assembly of multi-particle arrays by opto-hydrodynamic binding of microparticles close to a one-dimensional chain of magnetic microparticles

Multidomain Oriented Particle Chains Based on Spatial Electric Field and Their Optical Application.

Self-Assembly From The Branch Pattern To Parallel Wire Array In Electrodeposition

Template-Mediated Assembly Of Fept L1(0) Clusters Under External Magnetic Field

Conducting Nanopearl Chains Based on the Dmit Salt

A Novel Conductive Particle Dispersing Method via EHDA for POB-COG Packaging

Numerical study of interactive motion of dielectrophoretic particles

Self-templating Growth of Copper Nanopearl-Chain Arrays in Electrodeposition

Massive Electro-Microfluidic Particle Assembly Patterns in Droplet Array for Information Encoding

Dissipative particle dynamics simulation of self-assembly of phosphorylcholine-containing poly(L-lactide)

Reconfigurable Assembly of Planar Colloidal Molecules via Chemical Reaction and Electric Polarization

Particle aggregation by positive dielectrophoresis

Sorting of heterogeneous colloids by AC-dielectrophoretic forces in a microfluidic chip with asymmetric orifices