Abstract:In this study, equal channel angular pressing (ECAP) was applied to a hot-extruded Mg–5.00Zn–0.92Y–0.16Zr (wt.%) alloy to produce an ultrafine-grained a-Mg structure of 0.6μm with uniformly distributed fine quasicrystal Mg3YZn6 particles. The basal planes in the as-ECAPed alloy were inclined approximately 45° to the ECAP direction (EPD); thus, a high Schmid factor of 0.36 for (0001)〈112¯0〉 basal slip along EPD was obtained. Then, the superplastic behavior at low temperatures of 150–250°C and initial strain rates of 1.67×10−3s−1–1.67×10−1s−1 of the as-ECAPed alloy was investigated and compared with that of the as-extruded alloy. The microstructural development, texture evolution and cracking behavior during tensile tests were systemically investigated by electron backscattered diffraction (EBSD) analysis. During the tensile test along the EPD, the basal planes in the as-ECAPed alloy specimen were tilted approximately 15° away from the original position; thus, the basal planes were still in a position favorable for the basal slip along the EPD. As a result, a maximum elongation of 865% was obtained at 200°C and a strain rate of 1.67×10−3s−1, as a result of this favored basal texture and the excellent thermal stability of the ultrafine-grained structure. This optimum superplastic temperature of 200°C is much lower than that obtained for other Mg–Zn–Y–(Zr) alloys. In contrast, for the as-extruded alloy specimen, superplastic behavior did not occur until the critical condition of 250°C and a strain rate of 1.67×10−3s−1. Below this temperature and strain rate, the strong extrusion basal texture was maintained, and the cracks in the hot-worked coarse region (or un-DRXed region) were observed nucleating mainly associated with the formation of a 38° {101¯1}–{101¯2} double twin. At this temperature and strain rate, the hot-worked coarse regions were significantly refined by the dynamic recovery and the following recrystallization process. In the case, the formation of a double twin was prevented and the facture was delayed.

Effect of Temperature on the Mechanical Abnormity of the Quasicrystal Reinforced Mg–4%Li–6%Zn–1.2%Y Alloy

Temperature Effects on Deformation Substructures and Mechanisms of a Ni-based Single Crystal Superalloy

The Role of Nanoquasicrystals on the Ductility Enhancement of As-Extruded Mg–Zn–Gd Alloy at Elevated Temperature

Deformation Behavior of Mg–Zn–Gd-based Alloys Reinforced with Quasicrystal and Laves Phases at Elevated Temperatures

Effects of Heat Treatments on Microstructure and Mechanical Properties of Mg–4Y–4Sm–0.5Zr Alloy

Microstructure and Plastic Instability of Mg-4.3Li-1.08Y-5.83Zn Alloy

Effect of Hot Extrusion on Microstructure and Mechanical Properties of Quasicrystal-Reinforced Mg-Zn-Y Alloy

Mechanical Behavior and Failure Mechanism of an As-Extruded Mg-11 Wt％y Alloy at Elevated Temperature

Study on Tensile Behavior at Various Temperatures of the Mg-7Gd-5Y-1Nd-2Zn-0.5Zr Alloy

The Microstructural Evolution and Superplastic Behavior at Low Temperatures of Mg–5.00Zn–0.92Y–0.16Zr (wt.%) Alloys after Hot Extrusion and ECAP Process

Effect of Zn and Y on microstructures and properties of normally-solidified Mg-Zn-Y alloys

Effect of heat treatment on microstructure and mechanical properties of Mg-4Y-1.6Nd-1Sm-0.5Zr alloy

Abnormal temperature effect on tensile strength of Mg-13Gd-2Y-0.5Zr alloy

Effect of Icosahedral Phase on Crystallographic Texture and Mechanical Anisotropy of Mg–4%Li Based Alloys

The Influence of Temperature on the PLC Effect in Al-Mg Alloy

Effect of Aging Temperature on Microstructure and Mechanical Properties of Mg-12Gd-3Y-1Sm-0.5Zr Alloy

Microstructure Effects on Tensile Brittleness of As-Quenched Zl205A at Elevated Temperature

Influence of Extrusion Temperature on Microstructure and Mechanical Properties of Mg-4Y-4Sm-0.5Zr Alloy

Unveiling the mechanical response and deformation mechanism of extruded Mg-2.5Nd-0.5Zn-0.5Zr alloy sheet under high-temperature tensile

Microstructures and Mechanical Properties of Extruded Mg-9Gd-4Y-0.6Zr-T5 at Elevated Temperatures

Hot Compression Deformation Behavior of Mg-Zn-Al-(Y) Alloys Reinforced with Quasicrystal