Microwave-Assisted Highly Efficient Transformation of Ketose/Aldose to 5-Hydroxymethylfurfural (5-Hmf) in A Simple Phosphate Buffer System

Jinhua Lu,Yani Yan,Yahong Zhang,Yi Tang

DOI: https://doi.org/10.1039/c2ra21011h

IF: 4.036

2012-01-01

RSC Advances

Abstract:An acidic phosphate buffer system is developed to highly-selectively catalyze ketoses/aldoses dehydrating into 5-HMF without undesirable rehydration under microwave irradiation.

What problem does this paper attempt to address?

Experiments and Kinetic Modeling of Fructose Dehydration to 5-Hydroxymethylfurfural with Hydrochloric Acid in Acetone-Water Solvent

Youdi Zhang,Haoxiang Zhu,Zefeng Ji,Youwei Cheng,Liping Zheng,Lijun Wang,Xi Li

DOI: https://doi.org/10.1021/acs.iecr.2c02934

2022-01-01

Industrial & Engineering Chemistry Research

Abstract:This work presents experimental and kinetic modeling studies on fructose dehydration to 5-hydroxymethylfurfural (HMF) in the solution of mixed acetone and water, catalyzed by hydrochloric acid (HCl). A reaction scheme that added an intermediate was proposed. A corresponding kinetic model that considered the parameters, including temperature (383-423 K), initial substrate concentration (10-100 g/L), and catalyst concentration (5-60 mmol/L), was established, and the influence of solvent ratio (3-19) was also studied. The maximum yield was 91% in the ideal plug flow reactor under the optimized condition (T = 383 K, C-F0 = 10 g/L, C-HCl = 10 mmol/L). The model can well support the delicate reactor design since an industrially accessible HMF production process was proposed in this work.
Insight into the dehydration of high-concentration fructose to 5-hydroxymethylfurfural in oxygen-containing polar aprotic solvents

Zuojun Wei,En Yao,Yuran Cheng,Jinbo Hu,Yingxin Liu

DOI: https://doi.org/10.1039/d2nj01339h

IF: 3.3

2022-01-01

New Journal of Chemistry

Abstract:In this study, 1,4-dioxane and tetrahydrofuran are found to be the most suitable solvents for the dehydration of fructose at high concentrations, in which 77.7% and 78.8% yields of 5-hydromethylfurfural (5-HMF) are obtained, respectively, from 20 wt% fructose in the presence of an acid catalyst (5 mol% HCl, 11 wt% water). The high proportion of fructofuranose formed in those polar aprotic solvents and the reversible dimerization to the protective difructose dianhydrides determined by C-13 NMR and HPLC-MS, which stop fructose from excess cross-polymerization into unwanted humins, are considered to be the key factors for the satisfactory 5-HMF yield. Further addition of strong electrophilic molecules such as 5 mol% maleic acid, which consumes 2,5-dioxo-6-hydroxy-hexanal and blocks its reaction with 5-HMF by Michael addition, enhances the yield of 5-HMF to 85.4%.
Efficient One-Pot Production of 5-Hydroxymethylfurfural from Glucose in an Acetone–Water Solvent

Haoxiang Zhu,Youdi Zhang,Xusheng Guo,Youwei Cheng,Lijun Wang,Xi Li

DOI: https://doi.org/10.1021/acs.iecr.2c00502

2022-01-01

Industrial & Engineering Chemistry Research

Abstract:5-Hydroxymethylfurfural (HMF) is a high-valuebiomass-derived platform chemical derived from renewablebiomass, which is a great alternative to petroleum-based chemicals;however, it cannot be produced on a large scale at present becauseof the limitation of a low HMF yield and costly production. In thiswork, an experimental study of one-pot production of HMF fromglucose in an acetone-water solvent was conducted. The effects ofinorganic salts (in specific, NaCl) on miscible solvents were studiedbecause inorganic salts could affect the phase structure of solvents.We also study the influence of the ratio between Lewis acid andBronsted acid (L/B) on the dehydration reaction. After parameteroptimization experiments, up to 64.5% HMF yield was obtained at the condition ofC0= 1.25 w/v %,CAlCl3= 1.25 w/v %,CHCl=10mmolmiddotL-1,T= 160 degrees C, ando/a= 80/20, and the optimized L/B was 1.25 kgmiddotmol-1. Finally, an economic and efficient HMFproduction process including HMF purification and catalyst recycling was proposed; the HMF product could be produced andseparated with high recovery (similar to 88%) and purity (similar to 85%) in the process. Ourfindings and analysis would provide support for thechoice of the reaction system and bifunctional catalyst synthesis in the subsequent industrial demonstration development
Highly Efficient Production of 5-Methoxymethylfurfural from Fructose in Dimethyl Sulfoxide/Amberlyst-15 Catalytic System

Hui Yang,Feng Zhou,Hao Chen,Jing Li,Huixia Ma,Kequan Chen,Xiuyang Lu,Pingkai Ouyang,Jie Fu

DOI: https://doi.org/10.1021/acs.iecr.9b06392

2020-01-01

Industrial & Engineering Chemistry Research

Abstract:With the dwindling availability of fossil fuel resources and the dramatic increase in demand, 5-methoxymethylfurfural (MMF) obtained from renewable biomass resources has great potential as a fossil fuel alternative. In this work, a high yield (80.5%) of MMF was obtained from fructose catalyzed by Amberlyst-15 with the assistance of dimethyl sulfoxide (DMSO) in methanol at 100 degrees C for 10 h. Based on a detailed investigation of the reaction mechanism through the effects of DMSO, Amberlyst-15, reaction time, and reaction temperature on MMF yield and the existence of intermediates proved by FTIR, a two-step pathway was proposed: (1) DMSO and H ion on Amberlyst-15 act as a joint-catalyst [DMSOH](+), facilitating the dehydration of fructose into 5-hydroxymethylfurfural (HMF), and (2) [DMSOH](+) assists the etherification of HMF with methanol into MMF, which is the rate-determining step. This finding expands the concept of biomass conversion into biomass fuels and plays a vital role in catalyst screen and design, reaction medium selection, and industrial applications.
Selective 5-hydroxymethylfurfural production from cellulose formate in DMSO-H<sub>2</sub>O media

Caidi Jin,Ning Xiang,Xiao Zhu,E. Shuang,Kuichuan Sheng,Ximing Zhang

DOI: https://doi.org/10.1016/j.apcatb.2020.119799

2021-01-01

Abstract:5-hydroxymethylfurfural (HMF) can be widely converted into value-added chemicals and fuels production. Herein, we reported a sustainable and efficient approach for synthesizing HMF directly from cellulose. Facile formylation of cellulose with green and recyclable formic acid was developed for cellulose formate (CF) production. CF with special net-like structure and high degree of formyl substitution was prepared. The resultant CF exhibited excellent catalytic conversion and selectivity for HMF production comparable to monomeric glucose as reactant in dimethyl sulfoxide (DMSO)-H2O media. In our work, we presented molecular dynamics simulations to elaborate the preferential coordination of DMSO around formyl group, which promoted the solvation of formylated substrate in DMSO-H2O mixture, and the HMF yielded could be protected by DMSO without further degradation to levulinic acid or humins.
Condition screening and process investigation of aldose transformation in borate-containing acidic phosphate buffer system under microwave irradiation

yani yan,qingbin wu,xiao guo,jinhua lu,z h li,yahong zhang,yi tang

DOI: https://doi.org/10.1039/c4ra02612h

IF: 4.036

2014-01-01

RSC Advances

Abstract:The highly selective isomerization and dehydration of various carbohydrates (glucose, xylose, cellobiose and cellulose) are one-pot conversions conducted in a simple borate-containing phosphate buffer solution (PBS) under microwave irradiation. It is demonstrated that the key to glucose converting into 5-hydromethylfurfural (5-HMF) with a high selectivity is matching the isomerization and dehydration processes of glucose at the appropriate boron/glucose mole ratio (B/G) and pH of PBS with the aid of microwave irradiation. Moreover, the interaction between borate and glucose in the isomerization process has been demonstrated by both Raman spectra and theoretical calculations. Furthermore, the reusability of such a PBS system with borate has been accomplished by the successive addition of glucose and by the continual removal of 5-HMF in a biphasic system. These results not only deepen the understanding of the isomerization and dehydration behavior of glucose, but also provide the possibility for practical applications, owing to the appealing green, inexpensive and sustainable characteristics of such a catalytic system.
Efficient Conversion of Chitin into 5-Hydroxymethylfurfural Via a Simple Formylation Step under Mild Conditions

Chunxiao Gong,Zhaoyang Ju,Kuichuan Sheng,Ximing Zhang

DOI: https://doi.org/10.1039/d3gc00503h

IF: 9.8

2023-01-01

Green Chemistry

Abstract:A novel, sustainable, and efficient HMF production route from chitin was achieved via a simple formylation step under mild conditions.
Microwave-Assisted Production of 5-Hydroxymethylfurfural from Fructose Using Sulfamic Acid as a Green Catalyst

Vinícius Bertoncello Molon,Bruno Luís Ferreira,Carolina Colombo Tedesco,Maria Gabriele Delagustin,Thiago Barcellos

DOI: https://doi.org/10.3390/su16020858

IF: 3.9

2024-01-20

Sustainability

Abstract:The development of safe-by-design synthesis of valuable chemicals from biomass derivatives is a key step towards sustainable chemical transformations in both academia and industry. 5-Hydroxymethylfurfural (5-HMF) is a biomass derivative chemical of high commercial interest due to its wide range of chemical and biofuel applications. In this scenario, the present work contributes to a methodology for producing 5-hydroxymethylfurfural (5-HMF) through fructose dehydration reaction under microwave irradiation. The proposed protocol uses a simple sodium chloride–saturated aqueous-i-PrOH biphasic system and catalysis of sulfamic acid, a low-cost solid Brønsted–Lowry inorganic acid, which presents pivotal features of a sustainable catalyst. A 23 full factorial design was applied to achieve the highest conversion and 5-HMF yield, allowing the identification of the main factors involved in the process. Under the optimized conditions, fructose at the concentration of 120 g L−1 was converted with 91.15 ± 6.98% after 20 min at 180 °C, using 10 mol% of catalyst. 5-HMF was produced in 80.34 ± 8.41% yield and 73.20 ± 8.23% selectivity. Thus, the present contribution discloses a new optimized methodology for converting the biomass derivative fructose to 5-hydroxymethylfurfural (5-HMF).

environmental sciences,environmental studies,green & sustainable science & technology
Microwave‐Assisted Production of 5‐hydroxymethylfurfural from Glucose

Jameson Brett Mason,Yujie Sun

DOI: https://doi.org/10.1002/slct.202101984

2021-01-01

ChemistrySelect

Abstract:Among many biomass-derived intermediate compounds, 5-hydroxymethylfurfural (HMF) has been regarded as a platform chemical because it can be used to produce numerous valuable products. However, the difficulty of HMF isolation from reaction media coupled with its poor stability have significantly inhibited its large-scale production and application. In this work, we report a single-step process for the direct production of HMF from glucose using green chemical methods. Optimized glucose isomerization and dehydration under microwave irradiation achieved a respectable HMF yield (70 %) using a biphasic solvent mixture (water/THF), high glucose concentration (30 % w/v), catalytic amounts of AlCl3 (5 mol%) and HCl (15 mol%). The reaction can be completed within minutes at 165 degrees C. Overall, our microwave-assisted strategy enables the direct conversion of commercially available glucose to the highly valuable platform chemical HMF without the use of expensive solvents or catalysts, suggesting an economically attractive approach for upgrading carbohydrates.
Role of Reaction Adsorption on the Production of 5-Hydroxymethylfurfural from Fructose under Microwave Hydrothermal Process

Yanhong Wang,Lijiao Fan,Liqun Xiao,Lulu Wang,Dongsheng Shen,Yuyang Long

DOI: https://doi.org/10.1016/j.fuel.2023.127530

IF: 7.4

2023-01-01

Fuel

Abstract:5-Hydroxymethylfurfural (HMF) has been considered a valuable biomass-derived platform chemical that can be produced by hexose dehydration in the presence of an acid. However, the yield of HMF is always reduced because of side reactions such as rehydration and condensation. In this work, the reactive adsorption process of fructose dehydration to HMF catalyzed by hydrochloric acid under microwave condition was studied. BP2000 has better adsorption capacity than activated carbon (AC) in reactive adsorption, and addition of BP2000 in-creases the HMF yield. The maximum theoretical yield of HMF was 65 % obtained by adding 39 g L-1 BP2000 and reacting for 4 min at 160 degrees C under a microwave hydrothermal condition. It was discovered that microwave hydrothermal technology (MHT) could significantly increase efficiency and reduce reaction time. Reactive adsorption could efficiently buffer HMF from side reactions when reaction conditions became severe, thereby increasing the HMF yield. Reactive adsorption provides a more sustainable method for HMF production and separation.
Microwave-Assisted Catalytic Conversion of 5-HMF for Biofuel Additives by Molybdophosphoric Acid Encapsulated KCC-1

Srinivasan Vinju Vasudevan,Jin Cai,Junming Xu,Hongjian Lin,Hongliang Wang,Quan Bu

DOI: https://doi.org/10.3390/catal13060969

IF: 3.9

2023-01-01

Catalysts

Abstract:In this work, the microwave-assisted reaction of 5-hydroxymethylfurfural (5-HMF) into valuable ether and acylated production formation was investigated with the help of molybdophosphoric acid encapsulated dendritic fibrous silica (KCC-1) as a catalyst. XRD, N-2 adsorption-desorption, SEM, FT-IR, NH3-TPD, and TEM were used to analyze the physicochemical and structural properties of the synthesized catalysts. The microwave etherification of 5-HMF with ethanol was tested using synthesized catalysts. The effects of the reaction temperature, reaction time, catalytic amount, and microwave power were investigated. The resulting MPA-KCC-1 and IMPA-KCC-1 catalysts demonstrated excellent activity for the etherification of 5-HMF with ethanol, producing 5-(hydroxymethyl) furfural diethyl acetal (HMFDEA) and 5-(ethoxymethyl)furfural diethyl acetal (EMFDEA) products selectively. The significant advantages of the work are the selective production of EMFDEA at 82%, the catalyst can be easily removed via filtration, and the catalyst activity remains nearly intact even after five reaction cycles.
Conversion of Carbohydrates into 5-Hydroxymethylfurfural in an Advanced Single-Phase Reaction System Consisting of Water and 1,2-Dimethoxyethane

Shurong Wang,Haizhou Lin,Jingping Chen,Yuan Zhao,Bin Ru,Kunzan Qiu,Jinsong Zhou

DOI: https://doi.org/10.1039/c5ra18824e

IF: 4.036

2015-01-01

RSC Advances

Abstract:An advanced single-phase reaction system consisting of water–DMOE solvent and AlCl3 could be used efficiently and economically in HMF production.
Quantification of the Microwave Effect in the Synthesis of 5-Hydroxymethylfurfural over Sulfonated MIL-101(Cr)

Noor Aljammal,Jeroen Lauwaert,Bert Biesemans,Francis Verpoort,Philippe M. Heynderickx,Joris W. Thybaut

DOI: https://doi.org/10.3390/catal13030622

IF: 3.9

2023-03-21

Catalysts

Abstract:The potential benefits of microwave irradiation for fructose dehydration into 5 hydroxymethylfurfural (5-HMF) have been quantified over a sulfonated metal–organic framework (MOF), MIL 101(Cr)-SO3H. The effects of temperature (140–170 °C), batch time (5–300 min), and catalyst-to-substrate ratio (0.1–0.01 g/g) were systematically mapped. After 10 min of microwave (MW) irradiation at 140 °C in a DMSO–acetone reaction medium, practically complete fructose conversion was obtained with a 70% yield of 5-HMF. Without MW, i.e., using conventional heating (CH) at the same conditions, the fructose conversion was limited to 13% without any 5-HMF yield. Rather, 90 min of CH was required to reach a similarly high conversion and yield. The profound impact of moving from CH towards MW conditions on the reaction kinetics, also denoted as the microwave effect, has been quantified through kinetic modeling via a change in the Gibbs free energy of the transition state. The modeling results revealed an eight-fold rate coefficient enhancement for fructose dehydration owing to MW irradiation, while the temperature dependence of the various reaction steps almost completely disappeared in the investigated range of operating conditions.

chemistry, physical
Microwave Heating for Rapid Conversion of Sugars and Polysaccharides to 5-Chloromethyl Furfural

S. W. Breeden,J. H. Clark,T. J. Farmer,D. J. Macquarrie,J. S. Meimoun,Y. Nonne,J. E. S. J. Reid

DOI: https://doi.org/10.1039/c2gc36290b

2013-01-01

ChemInform

Abstract:A range of carbohydrates has been rapidly and selectively converted to 5-chloromethyl furfural using microwave heating in a biphasic reaction system with a range of organic solvents. Fructose and inulin were especially effective for production of this valuable bio-platform molecule, with yields of >70% obtained in 15 minutes under microwave heating. Yields from cellulose were dramatically increased with ball mill pre-treatment, this being associated with a reduction in polysaccharide crystallinity.
Promoting Electrocatalytic Hydrogenation of 5-Hydroxymethylfurfural Using Buffer Electrolytes As Proton-Donating Motifs: Theoretical Predictions and Experimental Validations

Xiao-Qiang Pan,Xin-Yu Zhang,Gui-Xiang Huang,Shu-Chuan Mei,Jia-Wei Huang,Jie-Jie Chen,Wu-Jun Liu,Han-Qing Yu

DOI: https://doi.org/10.1016/j.apcatb.2022.122191

2023-01-01

Abstract:Electrocatalytic hydrogenation (ECH) represents a promising alternative to conventional hydrogenation tech-niques with high-pressure H2 as a reductant. The proton-donating motif is an important factor governing the reaction efficiency but is usually overlooked in the ECH process. Herein, on the basis of density functional theory (DFT) predictions and experimental validations, we demonstrate that proton-buffer salts such as phosphate, carbonate and borate can greatly promote ECH efficiency. The DFT results predict that the buffer species can outperform water in donating protons for *C--O hydrogenation into *C-OH via the Langmuir-Hinshelwood or proton-coupled electron transfer (PCET) mechanism, thus promoting the hydrogenation of carbonyl compounds. The experimental results demonstrate that with the buffer-promoting effects, 5-hydroxymethylfurfural (HMF) can be effectively converted at an efficiency of 96 % into the value-added 2,5-dihydroxymethylfuran (DHMF) with a yield of 80 % over cobalt oxide (Co3O4) nanoarray catalysts under near-neutral buffer electrolyte. In situ Raman analysis and kinetic isotope experimental results reveal that the real mechanism is a combined Langmuir-Hinshelwood and PCET process. Such a buffer-promoting strategy also exhibits wide applicability in ECH of various other carbonyl compounds with different electrode catalysts. This work may provide a deep under-standing of the ECH process and open up new opportunities to design effective systems for the conversion of HMF into value-added products.
Kinetics of Xylose Dehydration into Furfural by Microwave Irradiation

Congguang Bai,Xuejun Liu,Yan Wang,Shizhong Li,Tiancheng Li,Lin Xiao

DOI: https://doi.org/10.3969/j.issn.1001-7631.2010.03.015

2010-01-01

Abstract:With dilute sulfuric acid as catalyst, the effects of reaction temperature and sulfuric acid concentration on xylose dehydration reaction were investigated under microwave irradiation. The kinetics equation of xylose dehydration was built. The results showed that the conversion of xylose increased with the increase of reaction temperature and mass fraction of sulfuric acid. The activation energy was 48.05 kJ/mol and the frequency factor changed with mass fraction of sulfuric acid. The conversion of xylose calculated by the kinetics equation was in good agreement with the conversion from experiment.
Conversion of bamboo fiber into 5-hydroxymethylfurfural catalyzed by sulfamic acid with microwave assistance in biphasic system

Jiankui Sun,Xiaodong Yuan,Yue Shen,Yuxuan Yi,Bo Wang,Feng Xu,Runcang Sun

DOI: https://doi.org/10.1016/j.indcrop.2015.03.044

IF: 6.449

2015-01-01

Industrial Crops and Products

Abstract:•NH2SO3H has the unique catalytic features and intrinsic zwitterionic property to catalyze degradation of bamboo fiber to produce HMF in biphasic system.•NaCl can be regarded as the continuous separation of HMF from water phase to organic phase.•Providing an approach for more effective utilization of bamboo fiber as potential feedstock.•Microwave assistance was high-efficiency.
Valorization of Hexoses into 5-Hydroxymethylfurfural and Levulinic Acid in Acidic Seawater under Microwave Hydrothermal Conditions

Yuchao Shao,Jiansong Chen,Xiaodong Ding,Wenjing Lu,Dongsheng Shen,Yuyang Long

DOI: https://doi.org/10.1080/09593330.2022.2143294

IF: 3.475

2022-01-01

Environmental Technology

Abstract:Typical value-added platform chemicals 5-hydroxymethylfurfural (HMF) and levulinic acid (LA) can be obtained from hexoses under microwave hydrothermal (MHT) conditions. This study explored the detailed transformation process regarding the MHT products in acidic seawater obtained using glucose and fructose as raw materials. The facile conversion of fructose compared with glucose was mainly ascribed to their different activation energies (56.721 and 88.594 kJ mol-1, respectively). The HMF and LA product yields were strongly affected by the MHT temperature and holding time in two types of hexose solution. Undesirable humins were found to inevitably form under each set of reaction conditions. The carbon balance results for reactants and products showed that up to 60% of fructose carbon was converted into value-added chemicals, while 47% of glucose carbon underwent the same conversion in acidic seawater under the optimal MHT conditions. This study provides further knowledge regarding the role of microwave heating combined with acidic seawater in green chemistry and is a useful reference for the biorefinery industry.
Selective HMF synthesis from glucose via microwave-assisted metal chloride catalysis

Jiawei Cai,Chao Xu,Weijian Shi,Shuping Wu

DOI: https://doi.org/10.1016/j.biombioe.2024.107060

IF: 5.774

2024-01-20

Biomass and Bioenergy

Abstract:Microwave-assisted heating technology is considered to be a novel catalytic method. In this study, the microwave method was combined with the low-toxic metal chloride catalyst AlCl 3 and the green solvent GVL, to directly catalyze the conversion of glucose to HMF with the assistance of the microwave. Under the optimized reaction conditions, the ratio of water to organic phase GVL was 4:6 as the solvent, and the yield of HMF was 74.04 % when the mixture was reacted for 10 min under 220 W microwave power. Using H 2 O and GVL as solvents, the obtained reaction solution will be divided into an aqueous layer and an organic layer. The catalyst AlCl 3 mainly exists in the aqueous layer, and the product HMF is mainly distributed in the organic layer. This facilitates the separation of HMF and the recycling of the catalyst. This work highlights an efficient and environmentally friendly reaction system, which is expected to provide ideas for the preparation of HMF on an industrial scale.

energy & fuels,biotechnology & applied microbiology,agricultural engineering
One-pot Conversion of Biomass-Derived Carbohydrates into 5-[(Formyloxy)methyl]furfural: A Novel Alternative Platform Chemical

Yetao Jiang,Wei Chen,Yong Sun,Zheng Li,Xing Tang,Xianhai Zeng,Lu Lin,Shijie Liu

DOI: https://doi.org/10.1016/j.indcrop.2016.01.004

IF: 6.449

2016-01-01

Industrial Crops and Products

Abstract:5-(Hydroxymethyl)furfural (HMF) is an important platform chemical, but the large scale production is limited by its instability. In this research, 5-[(formyloxy)methyl]furfural (FMF), derived from HMF, was produced directly from cellulose in formic acid reaction system with a yield of 33.4mol% at 150°C for 2h. Among numerous metal salt catalysts screened in this study, alkali metal bromides were found to be effective in catalyzing cellulose conversion to FMF. Bromide anions facilitation of the esterification of HMF to form FMF was confirmed. In addition, the effects of water, acid and other reaction parameters also were investigated when NaBr was used as the catalyst. Up to 2% of water or acid in this reaction system did not impact on the FMF yield. Increasing the temperature for every 20°C from 130°C to 170°C halved the reaction time but did not change the maximum yield. FMF was more hydrophobic and thermostable than HMF, which made it easier to be recovered. In a two-step process, FMF with a recovery of 29.4mol% and purity of 97mol% was obtained.

Microwave-Assisted Highly Efficient Transformation of Ketose/Aldose to 5-Hydroxymethylfurfural (5-Hmf) in A Simple Phosphate Buffer System

Experiments and Kinetic Modeling of Fructose Dehydration to 5-Hydroxymethylfurfural with Hydrochloric Acid in Acetone-Water Solvent

Insight into the dehydration of high-concentration fructose to 5-hydroxymethylfurfural in oxygen-containing polar aprotic solvents

Efficient One-Pot Production of 5-Hydroxymethylfurfural from Glucose in an Acetone–Water Solvent

Highly Efficient Production of 5-Methoxymethylfurfural from Fructose in Dimethyl Sulfoxide/Amberlyst-15 Catalytic System

Selective 5-hydroxymethylfurfural production from cellulose formate in DMSO-H<sub>2</sub>O media

Condition screening and process investigation of aldose transformation in borate-containing acidic phosphate buffer system under microwave irradiation

Efficient Conversion of Chitin into 5-Hydroxymethylfurfural Via a Simple Formylation Step under Mild Conditions

Microwave-Assisted Production of 5-Hydroxymethylfurfural from Fructose Using Sulfamic Acid as a Green Catalyst

Microwave‐Assisted Production of 5‐hydroxymethylfurfural from Glucose

Role of Reaction Adsorption on the Production of 5-Hydroxymethylfurfural from Fructose under Microwave Hydrothermal Process

Microwave-Assisted Catalytic Conversion of 5-HMF for Biofuel Additives by Molybdophosphoric Acid Encapsulated KCC-1

Conversion of Carbohydrates into 5-Hydroxymethylfurfural in an Advanced Single-Phase Reaction System Consisting of Water and 1,2-Dimethoxyethane

Quantification of the Microwave Effect in the Synthesis of 5-Hydroxymethylfurfural over Sulfonated MIL-101(Cr)

Microwave Heating for Rapid Conversion of Sugars and Polysaccharides to 5-Chloromethyl Furfural

Promoting Electrocatalytic Hydrogenation of 5-Hydroxymethylfurfural Using Buffer Electrolytes As Proton-Donating Motifs: Theoretical Predictions and Experimental Validations

Kinetics of Xylose Dehydration into Furfural by Microwave Irradiation

Conversion of bamboo fiber into 5-hydroxymethylfurfural catalyzed by sulfamic acid with microwave assistance in biphasic system

Valorization of Hexoses into 5-Hydroxymethylfurfural and Levulinic Acid in Acidic Seawater under Microwave Hydrothermal Conditions

Selective HMF synthesis from glucose via microwave-assisted metal chloride catalysis

One-pot Conversion of Biomass-Derived Carbohydrates into 5-[(Formyloxy)methyl]furfural: A Novel Alternative Platform Chemical