Abstract:The promising performance from the platinum group metal (PGM) catalysts make them the most practical catalysts for the commercialization of the polymer membrane fuel cells (PEMFCs). However, the excellent initial performance is not good enough for massive applications, particular for the fuel cell vehicles, which requires the long-term durability. Both the performance and the durability of catalysts strongly impact the applications in a wide range of operations of fuel cells, from stationary power generation to the transportation power propulsion. Catalyst stability plays a very important role on reducing the operation cost and increasing the lifetime of PEMFCs. Herein, a concept is proposed, which enhances the lifetime of PEMFCs through engineering the surface of catalyst supports. By covalently grafting NH2 groups on carbon (NGCB) surface, followed by polymerizing polyaniline (PANI) onsite on NFCB surface (using introduced NH2 groups as precursor), Pt L-edge goes to higher energy level, suggested by XAS measurement. Such modification can increase the barrier for Pt’s oxidation. In this study, carbon supports with different PANI loadings were synthesized and the Pt nanoparticles were loaded onto these supports. The synthesized catalysts were characterized for their morphology and structure using TEM, XRD, BET and Hg porosimetry. Both RDE and MEA tests were carried out for these catalysts for their fuel cell performance. The results show that the energy levels of Pt L-edge were increased with PANI loading. Besides, the membrane electrode assembly (MEA) testing results prove that the catalyst stability was improved with PANI loading in certain range. Three different PANI loadings were analyzed: 0.2, 0.25 and 0.33 in mass fraction of NFCB. MEAs results show that the beginning of life (BOL) performances of three catalysts were almost same. But when it comes to the catalyst stability test, the performance losses between BOL and EOL at 0.8 A·cm-2 in air are 120 mV, 90 mV and 45 mV for the three catalysts, respectively, after 30k square wave cycling using the standard testing protocol from the Department of Energy (DOE).

Aligned Polyaniline Nanorods in Situ Grown on Gas Diffusion Layer and Their Application in Polymer Electrolyte Membrane Fuel Cells

Construction of Homogeneous Catalyst Layers at Proton Exchange Membrane Fuel Cell Cathodes

Enhanced Catalyst Stability Via Chemically Grafted Polyaniline Groups for PEMFC

In Situ Construction of Ultra-Thin PANI/CeOx Layer on Proton Exchange Membrane for Enhanced Oxidation Resistance in PEMFC

Reticulated polyaniline nanowires as a cathode microporous layer for high-temperature PEMFCs

In Situ Grown Carbon Nanotubes on Carbon Paper As Integrated Gas Diffusion and Catalyst Layer for Proton Exchange Membrane Fuel Cells

Fabrication and Performance Evaluation of Tubular Catalyst Layer for Proton Exchange Membrane Fuel Cell

A Universal Strategy to Enhance Polarization Performance and Anode Reversal Tolerance by Polyaniline‐Coated Carbon Support for Proton Exchange Membrane Fuel Cells

Preparation of highly active and stable polyaniline-cobalt-carbon nanotube electrocatalyst for oxygen reduction reaction in polymer electrolyte membrane fuel cell

Synergistic Effect of Polyaniline on Stabilizing Pt Nanoparticles in PEMFCs

Bio-inspired Construction of Advanced Fuel Cell Cathode with Pt Anchored in Ordered Hybrid Polymer Matrix

Ionomer Cross-Linking Immobilization of Catalyst Nanoparticles for High Performance Alkaline Membrane Fuel Cells

Nanostructured Ultrathin Catalyst Layer Based on Open-Walled Ptco Bimetallic Nanotube Arrays for Proton Exchange Membrane Fuel Cells

Effect of gas diffusion layer surface property on platinum nanowire array electrode performance in proton exchange membrane fuel cells

In Situ Construction of a Nanostructured Ultrathin Catalyst Layer on Both Sides of a Membrane toward Fuel Cell Application

Vertically Aligned Titanium Nitride Nanorod Arrays As Supports of Platinum–Palladium–Cobalt Catalysts for Thin‐Film Proton Exchange Membrane Fuel Cell Electrodes

Ultrathin Nanoporous Metal Electrodes Facilitate High Proton Conduction for Low-Pt PEMFCs

Performance Enhancement of Proton Exchange Membrane Fuel Cell through Carbon Nanofibers Grown In Situ on Carbon Paper

Enhanced Catalytic Properties from Platinum Nanodots Covered Carbon Nanotubes for Proton-Exchange Membrane Fuel Cells

Nano-engineering of a 3D-ordered membrane electrode assembly with ultrathin Pt skin on open-walled PdCo nanotube arrays for fuel cells

Proton-Conducting Polymer-Coated Carbon Nanofiber Mats for Pt-Anodes of High-Temperature Polymer-Electrolyte Membrane Fuel Cell