Abstract:Wire arc additive manufacturing (WAAM) has been proved to be a promising method to fabricate large expensive NiTi shape memory alloys with complex geometry. In this study, five layers of NiTi alloy with dimensions of 80 × 12 × 15 mm were deposited by the cold metal transfer (CMT) welding based WAAM process. The macroscopic morphology, microstructure evolution, phase transformation and mechanical properties of each layer were investigated and compared with each other. Each layer of the as-deposited NiTi wall shows a one-step B2→B19′ transformation during cooling and the martensitic transformation temperature (Ms) is lower than that of the as-received wire. For the first three layers, the columnar grains growing along the building direction have a larger length-to-diameter ratio and B2 is the main constituent phase. Coarse dendritic Ti2Ni/Ti4Ni2O precipitates are precipitated at the interior of the grains besides grain boundaries. However, grains in the subsequent layers become finer and the region near the top surface are characterized by equiaxed grains, and elliptical Ti2Ni/Ti4Ni2O precipitates mainly concentrate at grain boundaries. The heat-affected zone exhibits the lowest hardness of 233.34HV, followed by a gradually increase among the as-deposited layers and the highest hardness of 331.27HV was obtained at the 5th layer. The highest ultimate tensile strength of 652.46Mpa, together with the elongation of 13.66% and recoverable strain of 2.39% was obtained in the sample which is located at 11.5 mm height away from the substrate. This research provides an innovative method and insights for additive manufacturing NiTi shape memory alloys by introducing CMT based WAAM method.

TIG Welding of TiNi Shape Memory Alloy.

Microstructure and Mechanical Behaviors of TiNiNb Wide Hysteresis Shape Memory Alloy Wire Argon Arc Welding Joint

Mechanical and Microstructural Characterization of Ultrasonic Welded NiTiCu Shape Memory Alloy Wires to Silver-Coated Copper Ferrules

Microstructure and Mechanical Properties of NiTi Alloy Prepared by Double-Wire + Arc Additive Manufacturing Plus In Situ Heat Treatment

Microstructure and properties of NiTi shape memory alloy fabricated by double-wire plasma arc additive manufacturing with a nearly equal atomic ratio

Functional and Mechanical Properties of As-Deposited and Heat Treated WAAM-Built NiTi Shape-Memory Alloy

Manufacturing technology and material characterization of ti 44ni47nb9alloy fastener ring by tungsten inert gas welding

Microstructure and Phase Transformation Behavior of NiTiCu Shape Memory Alloys Produced Using Twin-Wire Arc Additive Manufacturing

TEM study of the Ni-Ti shape memory micro-wire

Laser Welding of Niti Shape Memory Alloy Wires and Tubes for Multi-Functional Design Applications

Effect of Oxygen on Shape Recovery and Tensile Properties of Ti-Ni Alloy Weldments. GTA Welding of Ti-Ni Shape Memory Alloy (report 1).

Microstructure of Surface and Subsurface Layers of a Ni-Ti Shape Memory Microwire.

Manufacturing Technology and Material Characterization of Ti44Ni47Nb9 Alloy Fastener Ring by Tungsten Inert Gas Welding

Martensitic Transformation and Shape Memory Effect of Ti–49at.%Ni Alloys

Microstructure Evolution and Functional Response of NiTi Shape Memory Alloy Manufactured by Dual-Wire Electron Beam Freeform Fabrication

Study on Shape Recovery Temperature of Tini Alloy Laser Weld Joint

Study on the effect of double-sided laser welding of NiTi shape memory alloys wire

Effect of ultrasonic spot welding on the mechanical behaviour of NiTi shape memory alloys

Effect of Wire Feeding Speed on Dissimilar Laser Welding of NiTi Shape Memory Alloy and 2A12 Aluminum Alloy

Microstructures and mechanical properties of NiTi shape memory alloys fabricated by wire arc additive manufacturing

Mechanical and Functional Properties Degradation Mechanism of Electron Beam Welded NiTi Shape Memory Alloy