Abstract:Viscosity is a physical property of fluids and shows resistance to flow. In metallurgical slag, it directly affects various parameters of a metallurgical process such as reaction rate, separation effect, etc. The estimation of viscosity by models during a production process is considered to be much more effective owing to the production fluctuations and complexities of the slag composition. Many viscosity models have been developed in the past, such as the structural model with a wide range of adaptability and complex calculation process and the empirical and semiempirical models with simple structure and a narrow range of adaptability. The present paper proposed a new method to calculate the structural parameter (NBO/T) ratio (the amount of nonbridging oxygen per tetrahedral-coordinated atom), based on which the relationship between the viscosity of molten slag and (NBO/T) ratio was investigated. First, the viscosity model was applied to SiO2–ΣMxO slags, with the model parameters obtained by fitting the viscosity data of pure oxide and SiO2–MxO binary slag, and the average deviations were in the range of 9%–18.5%. Then, the model was extended to calculate the viscosity of SiO2–Al2O3–ΣMxO, a multicomponent complex aluminosilicate system, and Al2O3 was split into acid and basic oxides. Then the oxides were used for calculating the (NBO/T) ratio and viscosity activation energy based on the amphoteric behavior of Al2O3 in SiO2–Al2O3–MxO ternary slag system. Using the parameters of a SiO2–MxO binary system, the model parameters of the Al2O3-containing slag system were obtained by fitting the viscosity data of the SiO2–Al2O3–MxO ternary slag system with average deviations between 10% and 25%. In addition, the viscosity of a multi-complex system (SiO2–Al2O3–CaO–MgO–FeO–Na2O–K2O–Li2O–BaO–SrO–MnO) and its subsystems were also calculated using the model proposed in this paper, and the average deviations is less than 25%, which shows relatively accurate prediction results. The present model is based on the analysis of a slag structure and processing of data by an empirical method. This method has a better prediction effect and wider application range compared with the traditional empirical model, and it uses a simpler calculation process compared with the structure model.

A Novel Kinematic Model for Molten Slag Fiberization: Prediction of Slag Fiber Properties

A Novel Structural Viscosity Model for Coal Slag Melts

ANN-based structure-viscosity relationship model of multicomponent slags for production design in mineral wool

Investigation of Cooling Processes of Molten Slags to Develop Multilevel Control Method for Cleaner Production in Mineral Wool

A new prediction method for the viscosity of the molten coal slag. Part 1: The effect of particle morphology on the suspension viscosity

A New Prediction Method for the Viscosity of the Molten Coal Slag. Part 2: the Viscosity Model of Crystalline Slag

A structural viscosity model for silicate slag melts based on MD simulation

Model of estimating viscosity based on slag structure in entrained flow gasifier

Structurally-based Viscosity Model for Multicomponent Slag Systems

Fundamental Research and Applications of Blast Furnace Slag

A novel modeling method for the mechanical behavior of 3D woven fabrics considering yarn distortion

Numerical Simulation of Heat Transfer of Roller Slag in Centrifugal Preparation of Inorganic Fiber

Preparation of Slag Wool by Integrated Waste-Heat Recovery and Resource Recycling of Molten Blast Furnace Slags: From Fundamental to Industrial Application

Submodel for Predicting Slag Deposition Formation in Slagging Gasification Systems

Experimental research of producing slag wool with modified blast furnace slag as raw materials

Numerical Study of Melt-Spinning Dynamic Parameters and Microstructure Development with Ongoing Crystallization

Centrifugation fiberization experiment of molten slags and influencing factors of fiberization

A Novel Theoretical Model Development and Simulation of Melt‐Electrospinning Using Kane's and Udwadia–Kalaba Methods

Modeling of Advanced Melting Zone for Manufacturing of Optical Fibers

Modeling Viscosity of High Titania Slag

Experimental Research and Prediction Model on Viscosity of High FeO Content Slag