Abstract:Solar cavity receiver is a vital component in a solar power tower (SPT) system, where concentrated solar irradiation is absorbed, converted into heat and carried away by a kind of heat transfer fluid. The cavity receiver usually suffers from the high-flux and non-uniform concentrated solar irradiation, which would cause local overheating, large temperature gradient and even thermal stress fracture of the receiver and bring challenges for the safety of its daily operation. Therefore, it is necessary to investigate the thermal and mechanical performance of the solar cavity receiver. In the present study, a superheated water/steam solar cavity receiver with three boiling panels and a superheater was chosen as the physical model. An integrated simulation method, which couples the Monte-Carlo ray tracing (MCRT) method, the appropriate heat transfer correlations, the finite volume method (FVM) and the finite element method (FEM), was employed to simulate the complicated heat transfer process inside the receiver and conduct the thermal stress analysis for the absorber panels. With this method, the three-dimensional wall temperature and thermal stress distributions were gained both on the boiling panels and the superheater, and the causes of thermal stress induced by different temperature gradients were analyzed in detail. The following results were obtained: 1) The heat flux, wall temperature and equivalent thermal stress distributions all appear highly non-uniform on the absorber panels; 2) The hot spots can be found on the membrane wall between the elbows of the boiling panels, which can easily generate the high thermal stress due to the large temperature gradient with their surroundings; 3) The bi-axial stress at the outer and inner radius of the boiling tubes can be created by the large radial temperature gradient, and the thermal stress varies as a cosine distribution across the circumference of the superheated tubes, which is induced by the large temperature gradient in the circumferential direction. Besides, the spot-like areas with high thermal stress can also be found on the superheated tubes due to the considerable nonlinear axial temperature gradient. Moreover, the thermal stress on the membrane wall connected with both the boiling and the superheated tubes has the definite directionality, which shows parallel to the tubes or perpendicular to the tubes; 4) The thermal stress concentration always occurs at the high-temperature and structural discontinuity locations. Here, the thermal stress of the superheater is 360 MPa higher than that of the boiling panels. In general, the superheater has both the higher wall temperature and thermal stress, which is more crucial for the safe operation of the superheated water/steam solar cavity receiver.

Thermal analysis of solar central receiver tube with porous inserts and non-uniform heat flux

Heat Transfer Performance Analysis on a PVT Collector Fabricated by Modifying a Commercial Solar Cell

Thermal-fluid-mechanical analysis of tubular solar receiver panels using supercritical CO2 as heat transfer fluid under non-uniform solar flux distribution

Numerical Investigation on Porous Media Heat Transfer in A Solar Tower Receiver

Analysis on the Effects of Different Receiver Structures and Porous Parameters on the Volumetric Effects and Heat Transfer Performance of Porous Volumetric Solar Receiver

Experiment and optimization study on the radial graded porous volumetric solar receiver matching non-uniform solar flux distribution

Numerical investigation on heat transfer and thermoelastic stress in a solar cavity receiver

Numerical Investigation on Uniformity of Heat Flux for Semi-Gray Surfaces Inside a Solar Cavity Receiver

Analysis of Thermal Performance and Thermal Stress Using Two-Dimensional Thermoelastic Model for a 50 MWe External Cylindrical Solar Receiver

An Efficient 3D Tube-Level Flux-Thermal Model of External Tubular Receivers in Solar Power Tower Systems

Coupled optical and thermal simulation of the thermal performance of a 50 MWe external cylindrical solar receiver

Performance analyses and heat transfer optimization of parabolic trough receiver with a novel single conical strip insert

An optimized model and test of the China’s first high temperature parabolic trough solar receiver

Performance analysis of solar parabolic trough receiver with twisted perforated conical inserts

Thermal Characteristics and Thermal Stress Analysis of a Superheated Water/steam Solar Cavity Receiver under Non-Uniform Concentrated Solar Irradiation

Study on Heat Transfer and Stress Characteristics of the Pressurized Volumetric Receiver in Solar Power Tower System

Solar-thermal conversion investigation using surface partition method for a cavity receiver with helical pipe

Improving overall heat transfer performance of parabolic trough solar receiver by helically convex absorber tube

Numerical Simulation and Experimental Study of the Tube Receiver's Performance of Solar Thermal Power Tower

Thermal-hydraulic performance analysis of a novel parabolic trough receiver with double tube for solar cascade heat collection

EXPERIMENTAL AND SIMULATION INVESTIGATION ON A PARABOLIC TROUGH SOLAR COLLECTOR