Abstract:The limited availability of Te poses challenges for the widespread application of Bi2Te3-based thermoelectric modules. In this work, we explored the thermoelectric module potential of Te-free PbSe by elevating its power factor through crystal growth and slight-tuning vacancy and interstitial defects. The outcomes revealed a gradual increase in the carrier concentration and a high room-temperature carrier mobility of similar to 1750 cm(2) V-1 s(-1), leading to an enhanced power factor of similar to 37.4 mu W cm(-1) K-2 in Pb1.006Se+0.0016 Al crystals. We grew PbSe crystals to minimize the impact of grain boundaries on the charge carrier transport. Subsequently, n-type PbSe crystals were produced by introducing extra Pb to occupy the intrinsic Pb vacancies, effectively minimizing vacancy scattering. Following this, a minute quantity of small-sized Al (<= 2 parts per thousand) was introduced, revealing that these surplus Al atoms served as cationic dopants, substituting for Pb, while also occupying interstitial positions. The interstitial doping increases the carrier concentration while maintaining carrier mobility due to the distinct dimensions between the interstitial atoms and mean free path of electrons. The consistently improved power factor with the suppression of thermal conductivity brings about a significantly high ZT value over the whole temperature. Specifically, the ZT values of the Pb1.006Se+0.0016Al crystal reached similar to 0.5 at 300 K, similar to 1.5 at 673 K, and the average ZT (ZT(ave)) reached similar to 1.1 at 300-773 K. Ultimately, a single-leg power generation efficiency similar to 7.1% was achieved in Pb1.006Se+0.0016Al crystal and a 7-pair module reached a maximum temperature cooling difference similar to 51.2 K at the high temperature side T-h of 363 K. These results indicate the potential for developing a cost-effective and high-performance thermoelectric module utilizing PbSe.

Thermoelectric Power Generator Module Of 16x16 Bi2te3 And 0.6% Eras:(Ingaas)(1-X)(Inalas)(X) Segmented Elements

6 Watt Segmented Power Generator Modules using Bi<sub>2</sub>Te<sub>3</sub> and (InGaAs)<sub>1-x</sub>(InAlAs)<sub>x</sub> Elements Embedded with ErAs Nanoparticles

Power Generator Modules of Segmented Bi 2 Te 3 and ErAs:(InGaAs) 1− x (InAlAs) x

6 Watt Segmented Power Generator Modules using Bi 2 Te 3 and (InGaAs) 1-x (InAlAs) x Elements Embedded with ErAs Nanoparticles.

Power Generator Modules of Segmented BiTe and ErAs:(InGaAs)(InAlAs)

Segmented Power Generator Modules of Bi2te3 and Eras : Ingaalas Embedded with Eras Nanoparticles

Realizing High Energy Conversion Efficiency in a Novel Segmented‐Mg3(Sb, Bi)2/Cubic‐GeTe Thermoelectric Module for Power Generation

Design and Fabrication of Segmented GeTe/(Bi,Sb)2Te3 Thermoelectric Module with Enhanced Conversion Efficiency

Bismuth Telluride/Half‐Heusler Segmented Thermoelectric Unicouple Modules Provide 12% Conversion Efficiency

Fabrication and Characterization of Thermoelectric Power Generators with Segmented Legs Synthesized by One-Step Spark Plasma Sintering

Fabrication and Performance Simulation of Microscale Thermoelectric Modules Made with Bi2Te3-Based Alloys

Realizing High-Efficiency Thermoelectric Module by Suppressing Donor-Like Effect and Improving Preferred Orientation in N-Type Bi2(Te, Se)3

High efficiency GeTe-based materials and modules for thermoelectric power generation

Design, Fabrication, and Characterization of CMOS MEMS-Based Thermoelectric Power Generators

Fabrication And Evaluation Of Microscale Thermoelectric Modules Of Bi2te3-Based Alloys

Realizing High-Performance Thermoelectric Modules Through Enhancing the Power Factor Via Optimizing the Carrier Mobility in N-Type PbSe Crystals

Bi2Te3-Based Thermoelectric Modules for Efficient and Reliable Low-Grade Heat Recovery

All‐Mg3Sb2‐Based Module for Thermoelectric Power Generation

Structural Design for Wearable Self-Powered Thermoelectric Modules with Efficient Temperature Difference Utilization and High Normalized Maximum Power Density

Realizing a Superior Conversion Efficiency of ≈11.3% in the Group IV-VI Thermoelectric Module

Fabrication and evaluation of microscale thermoelectric modules of Bi<sub>2</sub>Te<sub>3</sub>-based alloys