Abstract:Microstructure characteristics are important for the high-performance Sm2Co17-type permanent magnets to achieve high intrinsic coercivity (H cj) and large magnetic field at the knee-point (H knee). In this work, the correlation between microstructures and magnetic properties has been systematically studied. The different microstructures were obtained by two procedures: by adjusting the aging temperature and optimizing the Zr content. On one hand, with increase of aging temperature from 1063 K to 1103 K, the cell size and the lamellar phase density increase from 75.1 nm and 0.014 1/nm to 101.5 nm and 0.043 1/nm, respectively, and the average peak Cu concentration at the cell boundaries reaches 21.9 at% which is helpful for obtaining relatively high H cj and H knee. As the aging temperature increases further to 1143 K, a much larger cell size and with incomplete cell boundaries results in an irregular distribution of Cu concentration at the cell boundaries. In this case, the H knee is low even though the magnet shows a high H cj. On the other hand, the increase of Zr content also promotes an increase in both the lamellar phase density and the average peak Cu concentration at the cell boundaries, giving rise to high H cj and H knee. Taking into consideration the aging temperature and Zr content, one can conclude that a lower aging temperature and lower Zr content produce a lower lamellar phase density and average Cu concentration at the cell boundaries and this leads to a lower H cj and H knee of the magnets. To further confirm this correlation between the microstructures and magnetic properties, a magnet of Sm(CobalCu0.062Fe0.285Zr0.016)7.6 was aged at a higher temperature of 1143 K to increase the lamellar phase density. As expected, the lamellar phase density increases from 0.008 to 0.013 1/nm; however, the cell size increases simultaneously from 142.5 to 247 nm. The magnet exhibits a much higher but uneven Cu concentration at the cell boundaries. As a result, the H cj increases from 1.64 to 10.18 kOe, while H knee just increases from 1.09 to 3.91 kOe.

Study of Smtm7.3 Microstructure by A Simplified Method and Its Correlation to Properties

Novel Method for Studying the Complex Microstructure of a Sm(Co/Fe/Cu/Zr)7.3 Permanent Magnet Alloy

Thermal stability and its effects on the mechanical properties of rapidly solidified Al-Ti alloys

The phase structure and electrochemical properties of the melt-spun alloy Zr0.7Ti0.3Mn0.4V0.4Ni1.2

Microstructure and properties of high strength, high conductivity Cu-2.5Fe-0.3Cr-0.3Mg-0.2Si-0.1Ca-0.1Zr alloy treated by multi-stage thermomechanical treatment

Microstructure and extrinsic magnetic properties of anisotropic Sm(Fe,Ti,V)12-based sintered magnets

Effect of microstructural evolution on high-temperature strength of 9Cr-3W-3Co martensitic heat resistant steel under different aging conditions

Influence of 1:7 H phase stability on the evolution of cellular microstructure in Fe-rich Sm-Co-Fe-Cu-Zr magnets

Microstructure Evolution of the Phase Change Material Tisbte

Microstructure Evolution and Crystallography of the Phase-Change Material TiSbTe Films Annealed in Situ

Temperature dependence of magnetization processes in Sm(Co,Fe,Cu,Zr)$_z$ magnets with different nanoscale microstructures

Growth of defects around grain boundary and evolution of cellular structure during isothermal aging process in 2:17-type SmCo permanent magnets

Microstructure and properties of Cu–Ni–Co–Si–Cr–Mg alloys with different Si contents after multi-step thermo-mechanical treatment

Effects of Sm Content on the Phase Structure, Microstructure and Magnetic Properties of the Sm Zr0.2(Fe0·8Co0.2)11.5Ti0.5 (x=0.8–1.4) Alloys

Effect of the Variation in Sm/Cu/Zr Contents on Phase Stability of a Sm(CoFeCuZr) 7.4 Permanent Magnet Alloy

Dependence of macromagnetic properties on the microstructure in high-performance Sm2Co17-type permanent magnets

Strip Casting of Sm2TM17-Type Alloys for Production of the Metastable SmTM7 Phase

Microstructural Characterization of Sm-Co Magnets

Microstructural and magnetic property evolution with different heat-treatment conditions in an alnico alloy

In Situ High-Temperature Transmission Electron Microscopy Investigation of Dynamic Element Migration for Sm-Co-Fe-Cu-Zr Sintered Magnets

Quantitative analysis of pinning-hardened intrinsic coercivity of Sm(CoFeCuZr)z (z = 7.0–7.8) high-temperature permanent magnets