Abstract:In view of its high precision and high efficiency, three-dimensional digital image correlation (3D-DIC) is widely used to accurately measure full-field deformation. A spatiotemporal experimental study using 3D-DIC to explore the Portevin–Le Chatelier (PLC) deformational behavior, provides a new insight into the whole 3D deformation field, including the out-of-plane displacement, and in particular the relationship between the serrations and the strain field in the deformation bands corresponding to individual serrations. Specimens 1, 2 and 3 mm thick of 5456 Al-based alloy were tested in uniaxial tension at room temperature at strain rates from 1.8 × 10 −4 to 9.1 × 10 −3 s −1 . The spatial and temporal characteristics of the strain localization were quantitatively analyzed. The out-of-plane displacement increment field ( w ) of the localized bands was observed by 3D-DIC, and found to be related to the specimen thickness and the in-plane strain increment. The largest displacement increments were respectively 15, 10 and 5 μ m for 3, 2 and 1 mm specimens at maximum strain increment of about 12000 μ ε . The elastic shrinkage outside the deformation bands was found to be an essential characteristic of the PLC effect. The width of the PLC band ( w b a n d ) increased with increasing thickness; the angle of the PLC band ( 𝜃 b a n d ) was not affected by either specimen thickness or serration amplitude. Temporally, the serrations in the plots both of in-plane strain and out-of-plane displacement vs. time coincided throughout the entire loading procedure. When PLC banding occurred, the serration amplitude within the bands was found to be proportional to the maximum strain increment in the direction of the applied tensile force ( 𝜖 m a x ).

Investigation of Portevin-Le Chatelier Effect in 5456 Al-based Alloy Using Digital Image Correlation

On the Propagation and Pulsation of Portevin-Le Chatelier Deformation Bands: an Experimental Study with Digital Speckle Pattern Metrology

The Portevin-Le Chatelier Effect in Al-Mg Alloy Investigated by Infrared Pyrometry

Characterization of Portevin–Le Chatelier Effect in Aluminum Alloy AA5052 under Strain-Controlled Tensile Test Via Digital Image Correlation and Acoustic Emission

3D Digital Image Correlation Investigation of PLC Effect in a New Ni–Co Base Superalloy

Experimental Study on Three-Dimensional Deformation Field of Portevin–Le Chatelier Effect Using Digital Image Correlation

Characterization of the deformation behaviors associated with the serrated flow of a 5456 Al-based alloy using two orthogonal digital image correlation systems

EFFECT OF PRECIPITATE ON PLC EFFECT IN 2024 Al ALLoY

White-Light Digital Speckle Image Correlation Analysis of the Portevin-Le Chatelier Shearing Band in Multiscale

DIC/DSI Based Studies on the Local Mechanical Behaviors of HR3C/T92 Dissimilar Welded Joint During Plastic Deformation

Experimental Investigation on the Influence of Mg Content on Portevin-Le Chatelier Effect in Al-Based Alloys by Using Digital Image Correlation

Spatial characteristics of the Portevin-Le Chatelier deformation bands in Al-4 at%Cu polycrystals

Investigation on Portevin-Le Chatelier Effect in a Ni-Co Based Superalloy Base on Digital Speckle Correlation

Experimental investigations on kinetics of Portevin–Le Chatelier effect in Al–4wt.%Cu alloys

On the spatio-temporal characteristics of the Portevin-Le Chatelier effect in aluminium alloy AA5182: An experimental and numerical study

Investigation of Portevin–Le Chatelier Band Strain and Elastic Shrinkage in Al-Based Alloys Associated with Mg Contents

The Portevin-Le Chatelier (PLC) effect in an Al-Cu aluminum alloy fabricated by selective laser melting

Digital Shearography Investigation on the Out-Plane Deformation of the Portevin-Le Chatelier Bands

Multiscale Analysis And Numerical Modeling Of The Portevin-Le Chatelier Effect

Effects of Various Shape Functions and Subset Size in Local Deformation Measurements Using Dic

Thermal Analyses and Simulations of the Type A and Type B Portevin–Le Chatelier Effects in an Al–Mg Alloy