Abstract:In this paper, a kind of flexible shield for thermal neutron is fabricated through blending functional B 4 C powder with thermoplastic elastomer polystyrene- block -poly(ethylene- ran -butylene)- block -polystyrene(SEBS) in a banbury mixer, and weight fractions[(M B4C : M SEBS )%] of the composites are prepared as 10%, 20%, 30%, 40%, 60%, 100% respectively. B 4 C powders are well dispersed in the matrix of SEBS through microscopic observation, even without chemical interaction between the chemical groups of SEBS and the fillers. The elongations at break and tensile strengths of the B 4 C/SEBS composites deteriorate rapidly compared with the virgin sample, but it seems the tensile and tear strength could still maintain a satisfactory value suitable for preparing super flexible shields. The hardness of the composites is in the range of 15-25 HA. Based on a self developed nondestructive testing device, shielding abilities of the samples are estimated by neutron transmittance, 10 B areal density, linear attenuation coefficient, and thickness of half value layer. The neutron transmittance is 71.31%-32.43% corresponding to 10 B areal density ranging from 2.1873 mg/cm 2 to 17.6314 mg/cm 2 , linear attenuation coefficient is 0.1932-0.6435 mm -1 , and half value layer value is 3.59-1.08 mm. It is also proved that the neutron transmittance measured shows an exponential attenuation with the increase of 10 B areal density. The most importantly, the areal uniformity of neutron transmittance, with standard deviation less than 0.76%, is validated for the achievement of excellent attenuation of thermal neutrons in all directions. Consequently, results show excellent flexible and shielding performances of the functional composites.

Preparation and Properties of B4c/Graphite Neutron Absorption Ball

Preparation and Properties of B<sub>4</sub>C/Graphite Neutron Absorption Ball

Preparation of Absorption Sphere of High Temperature Gas Cooled Reactor

Effect of TiB_2 content on microstructure and mechanical properties of in-situ fabricated TiB_2/B_4C composites

Graphite–boron Composite Heater in a Kawai-type Apparatus: the Inhibitory Effect of Boron Oxide and Countermeasures

Study on the Thermophysical Properties of 80% 10B Enrichment of B4C

Ballistic Performance of B4C/Al2O3 Composite Ceramic Prepared by Reaction Sintering

Properties and thermal neutron areal transmittance of a B 4 C filled thermoplastic elastomer based rubber composite

The Design Study of a New Nuclear Protection Material

Structure and mechanical properties of hot-pressed B4C-NdB6 composites

Cold-Sprayed W/B4C/Al Coatings for Neutron and γ-Rays Absorption

In-Situ Doping B4C Nanoparticles in Mesophase Pitch for Preparing Carbon Fibers with High Thermal Conductivity by Boron Catalytic Graphitization

Preparation of the Novel B4C–SiC Composite Aerogel with High Compressive Strength and Low Thermal Conductivity

Preparation of dense B4C ceramics by spark plasma sintering of high-purity nanoparticles

Structure of Carbon-Coated Graphite and Its Application in Nuclear Industry

B4C-SiC skeleton reinforced graphite composites with excellent mechanical properties

Fabrication and characterization of hot-pressed B-rich boron carbide

A Review of Recent Studies of Fabrication of Al–B4C Composite Sheets Used in Nuclear Metal Casks

The improvement mechanism of mechanical properties of B4C ceramics by constructing core‐shell powders

High-performance B4C matrix composites fabricated from the B4C–Si–CeO2 system via reactive hot pressing

A novel B 4 C/Al-316 L neutron absorbing clad plate prepared by cold spraying: Microstructure and mechanical properties