Abstract:Catalyst layers for proton exchange membrane fuel cells (PEMFCs) are typically prepared by first dispersing a catalyst powder, comprised of platinum or platinum alloy nanoparticles supported on carbon blacks, with ionomer in solvent followed by extensive mixing using a variety of methods. The purpose of the ink mixing and processing procedure it to break up large agglomerates of the catalyzed carbon powder (>10 μm) and form a uniform dispersion, However, care must be taken to limit damage to the catalyst particles. Following the dispersing process, the catalyst ink is applied to the surface of the substrate (membrane, diffusion media, or transfer liner) through a variety of coating processes (painting, spraying, screen printing, etc.) [1]. In addition to creating coating defects, large agglomerates resulting from inadequate ink processing can limit catalyst utilization, inhibit mass transport in the catalyst layer, and damage the membrane and possibly also the gas diffusion layer. This can lower beginning-of-life performance by creating transport barriers for oxygen, hydrogen, and protons, and can increase membrane pinhole formation and electrical shorts, thus limiting the cell lifetime. This presentation will describe ink compositions and processing techniques for efficient coating of catalyst layers while optimizing cell performance and lifetime and minimizing ink processing time and cost [2, 3]. Ultra-small angle X-ray scattering (USAXS) was used to measure the agglomerate size distribution during ink mixing/processing. The experimental setup for the USAXS evaluation of inks during sonication is shown in Figure 1. A flask containing catalyst ink was immersed in an ice bath and sonicated using a water bath and/or a horn sonicator and pumped through a thin-walled capillary tube situated in the X-ray beam using a peristaltic pump. The effects of catalyst ink composition and processing variables on catalyst agglomerate size and ink properties were evaluated using different solvents, ionomer-carbon ratios, support types, and sonication time. The proper ink composition and sonication method that facilitate the break-up of carbon agglomerates with the minimum amount of time were determined. The electrochemically-active surface areas of the catalyst after the ink processing were determined using aqueous electrochemical methods to determine the extent of damage to the catalyst after processing (e.g., dislodging of catalyst particles from the support). The correlation of ink processing conditions and agglomerate structure with fuel cell performance will also be described. Acknowledgements This work was supported by the U.S. Department of Energy (DOE), Energy Efficiency&Renewable Energy, Advanced Manufacturing Office, Roll-to-Roll Advanced Materials Manufacturing DOE Laboratory Consortium. This research used the resources of the Advanced Photon Source (APS), a U.S. DOE Office of Science User Facility operated for the DOE Office of Science by Argonne National Laboratory under Contract No. DE-AC02-06CH11357. References [1] B. Bladergroen, H. Su, S. Pasupathi, V. Linkov, Chapter 3, Electrolysis, INTECH, 2012. [2] S. A. Mauger, K. C. Neyerlin, A. C. Yang-Neyerlin, M. Ulsh, 232nd ECS Meeting, National Harbor, MD, October 1-5, 201. [3] I. V. Zenyuk, N. Englund, , G. Bender, A. Z. Weber and M. Ulsh, J. Power Sources 332 (2016) ,372–382. Figure 1

Preparing Two-Dimensional Nano-Catalytic Combustion Patterns Using Direct Inkjet Printing

Application of Inkjet Printing to Fabricate Controllable Pt Catalyst Patterns for Low Temperature Catalytic Combustion

Direct ink writing of Pd-Decorated Al<sub>2</sub>O<sub>3</sub> ceramic based catalytic reduction continuous flow reactor

Preparation of Nickel-Foam-supported Pd/NiO Monolithic Catalyst and Construction of Novel Electric Heating Reactor for Catalytic Combustion of VOCs

Novel metallic electrically heated monolithic catalysts towards VOC combustion

Inkjet Printing of a Micro/Nanopatterned Surface to Serve as Microreactor Arrays

Effects Of The Nanoimprint Pattern On The Performance Of A Mems-Based Micro Direct Methanol Fuel Cell

In Situ X-Ray Scattering Characterization of PEMFC Catalyst Ink Microstructure during Ink Processing

Direct Ink Writing of Hierarchical Porous SiC Ceramics As Catalyst Support for Hydrogen Production

3D printing of combustive inks for hierarchically porous electrochemical electrodes

Evaluation of Micro Catalytic Combustor Using Tape-casting Ceramic Structure

Design and Experimentation with Sandwich Microstructure for Catalytic Combustion-Type Gas Sensors

Inkjet Printing Assisted Synthesis Of Multicomponent Mesoporous Metal Oxides For Ultrafast Catalyst Exploration

Temperature-Driven Dissolution of Nanoalloyed Catalyst During Ink Preparation and Membrane Electrode Assembly Fabrication

Rapid Inkjet Printing of High Catalytic Activity Co3O4/N-rGO Layers for Oxygen Reduction Reaction

Discovery of A New Catalyst for Photocatalytic Hydrogen Production: Parallel Ink-Jet Printing Synthesis of Multicomponent Mesoporous Metal Oxides Library

Investigation of Catalyst Ink Dispersion Using Small Angle X-ray and Small Angle Neutron Scattering

Pt Nanostructures Fabricated by Local Hydrothermal Synthesis for Low-Power Catalytic-Combustion Hydrogen Sensors

Evaluating Ink Structure Using Ultrasonic Spray Coating for PEMFC MEA

The Controllable Design of Catalyst Inks to Enhance PEMFC Performance: A Review

Direct ink writing of Pd-Decorated Al2O3 ceramic based catalytic reduction continuous flow reactor