Abstract:Dimethyl ether (DME) is a highly reactive diesel substitute that can be used as a pilot fuel to ignite low- reactivity methane (CH4) in heavy-duty engines. To optimize the efficiency and emissions of CH4/DME dual-fuel engines, it is crucial to study the fundamental combustion characteristics of DME mixed with methane. This study focuses on the influence of CH4 addition on the low-temperature oxidation (LTO) preparation stage and the thermal ignition (TI) preparation stage of DME in the two-stage ignition process, as these two stages respectively control the ignition delay of the first and second stages. The comparison is made between pure DME and a 50% CH4 and 50% DME blended fuel, operating under thermodynamic conditions representing the engine in- cylinder environment at 30 atm pressure, 650K temperature, and a stoichiometric equivalence ratio. The results show that the addition of methane hardly affects the control mechanism of the two-stage ignition of DME. Specifically, the LTO preparation stage is still promoted by the increase in OH radicals in the DME’s low-temperature oxygenation pathways to form KET, and the second stage is still controlled by the H2O2 loop mechanism. The kinetic analysis also reveals that methane addition can compete for some of the OH radicals in the LTO preparation stage, which has a suppressing effect on ignition. However, in the TI preparation stage, methane can promote the loop reaction of OH→HO2→H2O2→OH and promote ignition. For the operating conditions studied here, although methane consumes a total of 7.24% prior to thermal ignition, it only consumes 0.63% of the total amount in the LTO preparation stage and 1.81% of the total amount in the TI preparation stage. This indicates that methane is mainly consumed in the LTO stage, accounting for 65% of the total methane consumption amount. It can be concluded that the kinetic effect of methane has a relatively small impact on the ignition delay of the DME, at least for the conditions investigated here. In other words, the dilution and thermal effects caused by adding methane are the main reasons for the prolonged time of LTO/TI preparation. Overall, more fundamental research is warranted to understand the role of methane in the two-stage ignition process of DME, which could facilitate the development of CH4/DME dual-fuel engines.

Experimental and Kinetic Study on Ignition Delay Times of Dimethyl Carbonate at High Temperature

Experimental and modeling study of the ignition kinetics of dimethyl carbonate

An Experimental and Kinetic Modeling Study on Dimethyl Carbonate (dmc) Pyrolysis and Combustion

Experimental and numerical study on the ignition delay times of dimethyl ether/propane mixtures in O2/CO2 atmospheres

An experimental and detailed kinetic modeling study of the pyrolysis and oxidation of DMF over a wide range of conditions

Experimental and modeling study of ignition delay times of n-C5H12 and C3H6 under O2/CO2 atmospheres

Experiments and Modeling of the Autoignition of Methylcyclohexane at High Pressure

Experiments and Modeling of the Autoignition of Methyl-Cyclohexane at High Pressure

Shock tube experiments and kinetic modeling of ignition of unsaturated C 5 methyl esters

A shock tube study of the ignition delay time of DME/ammonia mixtures: Effect of fuel blending from high temperatures to the NTC regime

Shock tube and modeling study on the ignition delay times of ammonia/dimethoxymethane at high temperature

Exploring the High-Temperature Kinetics of Diethyl Carbonate (DEC) under Pyrolysis and Flame Conditions

The Effect of Methane Addition on the Low-Temperature Oxidation Preparation and the Thermal Ignition Preparation of Dimethyl Ether under Representative Engine In-Cylinder Thermal Conditions

Experimental Study of 2,5-Dimethylfuran and 2-Methylfuran in a Rapid Compression Machine: Comparison of the Ignition Delay Times and Reactivity at Low to Intermediate Temperature

Stage-wise Kinetic Analysis of Ammonia Addition Effects on Two-Stage Ignition in Dimethyl Ether

Autoignition of methyl palmitate in low to intermediate temperature: Experiments in rapid compression machine and kinetic modeling

Investigation of the Effect of Ammonia Addition on the Two-Stage Ignition Process of Dimethyl Ether Based on Chemical Kinetic Analysis

Investigation of Methanol Ignition Phenomena Using a Rapid Compression Machine

Ignition-delay-time/time-resolved CO2-concentration Measurements During the Combustion of Ic4h10/h2 Mixtures

Experimental Study of Ignition Behaviors of Pyrolysis Gas of Kerosene‐based Endothermic Hydrocarbon Fuel

Experimental and computational study of nonpremixed ignition of dimethyl ether in counterflow