Demonstration of Low Power Radiation Pressure Actuation for Control of Test Masses

M Feat,C Zhao,L Ju,DG Blair

DOI: https://doi.org/10.1063/1.1867472

2005-01-01

Abstract:We demonstrate a scheme for radiation pressure force actuation for noncontacting control of a suspended test mass. We present results of the frequency response and active damping of a 35 g low frequency resonator under radiation pressure using less than 1 W of diode laser power.

What problem does this paper attempt to address?

Radiation Pressure Actuation of Test Masses

F Garoi,L Ju,C Zhao,DG Blair

DOI: https://doi.org/10.1088/0264-9381/21/5/075

IF: 3.5

2004-01-01

Classical and Quantum Gravity

Abstract:In this paper, we investigate the use of radiation pressure force as test mass actuation for laser interferometer gravitational wave detectors. It is shown that it is viable to provide radiation pressure control on test masses for frequencies above ~0.2 Hz in high performance vibration isolation systems. A very low mass, low frequency resonator has been used to verify that radiation pressure force is not corrupted by other forces such as due to radiometer effects.
A simple table-top demonstration of radiation pressure on a macroscopic object

G. Jesensky,D. Dams,O. Khomenko,W. J. Kim

DOI: https://doi.org/10.48550/arXiv.1606.01919

2016-05-27

Physics Education

Abstract:We report a simple demonstration of radiation pressure on a table-top experiment. Utilizing dynamic force microscopy in ambient environment, the resonant motion of a cm-sized cantilever driven by an amplitude-modulated diode laser is directly observed. Our versatile setup involves a host of exciting techniques that are relevant in precision force measurements and represents an ideal experiment in the undergraduate laboratory.
A Contactless Methodology of Picking Up Micro-Particles from Rigid Surfaces by Acoustic Radiation Force

Kun Jia,Keji Yang,Zongwei Fan,Bing-Feng Ju

DOI: https://doi.org/10.1063/1.3676636

2012-01-01

Abstract:Controlled movement and pick up of small object from a rigid surface is a primary challenge in many applications. In this paper, a contactless methodology of picking up micro-particles within deionized water from rigid surfaces by acoustic radiation force is presented. In order to achieve this, an acoustic radiation force was generated by 1.75 MHz transducers. A custom built setup facilitates the optimization of the sound field by varying the parameters such as sound source size and source position. The three-dimensional pressure distributions are measured and its relative sound field is also characterized accordingly. The standing wave field has been formed and it is mainly composed of two obliquely incident plane waves and their reflectors. We demonstrated the gripping and positioning of silica beads, SiO2, and aluminum micro-particles of 100 μm to 500 μm in size with this method using acoustic radiation force. The acoustic radiation force generated is well controlled, contactless, and in the tens of nano-Newton range which allowed us to manipulate relative big micro objects such as MEMS components as well as moving objects such as living cells. The proposed method provided an alternative form of contactless operating environment with scalable dimensions suitable for the manipulating of small objects. This permits high-throughput processing and reduction in time required for MEMS assembling, cell biomechanics, and biotechnology applications.
Feedback control and characterization of a microcantilever using optical radiation pressure

David M. Weld,Aharon Kapitulnik

DOI: https://doi.org/10.1063/1.2362598

IF: 4

2006-10-16

Applied Physics Letters

Abstract:The authors describe a simple method for feedback regulation of the response of a microcantilever using the radiation pressure of a laser. A modified fiber-optic interferometer uses one laser to read out the position of the cantilever and another laser of a different wavelength to apply a force that is a phase-shifted function of that position. The method does not require a high-finesse cavity, and the feedback force is due solely to the momentum of the photons in the second laser. The feedback phase can be adjusted to increase or decrease the microcantilever’s effective quality factor Qeff and effective temperature Teff. The authors demonstrate a reduction of both Qeff and Teff of a silicon nitride microcantilever by more than a factor of 15 using a root-mean-square optical power variation of ∼2μW. Additionally, the authors suggest a method for determination of the spring constant of a cantilever using the known force exerted on it by radiation pressure.

physics, applied
Radiation-Pressure-Mediated Control of an Optomechanical Cavity

Jonathan Cripe,Nancy Aggarwal,Robinjeet Singh,Robert Lanza,Adam Libson,Min Jet Yap,Garrett D. Cole,David E. McClelland,Nergis Mavalvala,Thomas Corbitt

DOI: https://doi.org/10.1103/PhysRevA.97.013827

2017-12-05

Abstract:We describe and demonstrate a method to control a detuned movable-mirror Fabry-Perot cavity using radiation pressure in the presence of a strong optical spring. At frequencies below the optical spring resonance, self-locking of the cavity is achieved intrinsically by the optomechanical (OM) interaction between the cavity field and the movable end mirror. The OM interaction results in a high rigidity and reduced susceptibility of the mirror to external forces. However, due to a finite delay time in the cavity, this enhanced rigidity is accompanied by an anti-damping force, which destabilizes the cavity. The cavity is stabilized by applying external feedback in a frequency band around the optical spring resonance. The error signal is sensed in the amplitude quadrature of the transmitted beam with a photodetector. An amplitude modulator in the input path to the cavity modulates the light intensity to provide the stabilizing radiation pressure force.

Quantum Physics,Optics
Optical power meter using radiation pressure measurement

Patrick Pinot,Zaccaria Silvestri

DOI: https://doi.org/10.1016/j.measurement.2018.07.087

2018-07-02

Abstract:This paper describes a radiation pressure meter based on a diamagnetic spring. We take advantage of the diamagnetic property of pyrolytic carbon to make an elementary levitated system. It is equivalent to a torsional spring-mass-damper system consisting of a small pyrolytic carbon disc levitated above a permanent magnet array. There are several possible measurement modes. In this paper, only the angular response to an optical power single-step is described. An optical detection composed of a laser diode, a mirror and a position sensitive detector (PSD) allow measurement of the angular deflection proportional to the voltage delivered by the PSD. Once the parameters of the levitated system depending on its geometrical and physical characteristics have been determined regardless of any optical power, by applying a simple physical law, one can deduce the value of the optical power to be measured from the measurement of the first maximum of the output voltage amplitude.

Applied Physics,Instrumentation and Detectors
A Hybrid Photovoltaic/flexoelectric Actuation Mechanism Applied to Precision Actuation and Vibration Control of Beams

Yan Deng,Hornsen Tzou

DOI: https://doi.org/10.1007/s00707-023-03828-4

IF: 2.645

2024-01-01

Acta Mechanica

Abstract:Photo-driven flexoelectric actuators combine the advantages of wireless photovoltaic generator and flexoelectric precision actuation, and thus can realize non-contact precision actuation and vibration control of structures. This study presents a novel hybrid photovoltaic/flexoelectric actuation mechanism by using PbLaZrTi (PLZT) as a photovoltaic generator to drive a flexoelectric actuator consisting of an atomic force microscope (AFM) probe and a flexoelectric layer covered with an electrode layer. Spatial-time distributions of the opto-flexoelectric-induced control moments are calculated. Static deflection control and dynamic vibration control of cantilever beams are investigated, and independent modal control effects are evaluated. Analysis results demonstrate that this photovoltaic/flexoelectric actuation mechanism can effectively accelerate the beam damping process. The control effects by the Lyapunov controls are better than those via the proportional feedback and velocity feedback controls. The customization of modal control forces can be realized via a non-contact strategy by adjusting the light intensity and pre-illumination time. Design issues related to the optimal position of AFM probe and actuator size are also addressed.
Radiation pressure approach to the measurement of single-pulse microwave power

Keqian Zhang,Dun Wang,Zhenyu Wang

DOI: https://doi.org/10.1109/ICMMT.2002.1187916

2002-01-01

Abstract:In this paper, the possibility of using electromagnetic wave radiation pressure to the measurement of microwave power, especially the measurement of the peak power or total energy in a single shot high-energy microwave pulse is discussed. A torsion balance with a suspension system for measuring the radiation pressure in free space is proposed. System simulation of the real-time response of the suspension system is made. Some experimental results are presented.
Implementation of Electrostatic Actuators for Suspended Test Mass Control

BH Lee,L Ju,C Zhao,DG Blair

DOI: https://doi.org/10.1088/0264-9381/21/5/089

IF: 3.5

2004-01-01

Classical and Quantum Gravity

Abstract:We present our findings on recent experiments involving the use of electrostatic actuators for control of test masses suspended by flexure membranes. The actuator design and its proposed implementation for AIGO are described. With the use of first generation DSP controllers developed at VIRGO, we demonstrate the successful control of the tilt of a suspended dummy test mass in a typical seismic environment. Problems of the coupling of translation and tilt modes in a niobium flexure suspended test mass are discussed and possible solutions are presented.
Measurement of microwave radiation pressure on thin metal fibers

Mykola Kokodii,Sergey Berdnik,Victor Katrich,Mikhail Nesterenko,Ivan Priz,Anastasia Natarova,Vyacheslav Maslov,Konstantin Muntian

DOI: https://doi.org/10.24027/2306-7039.4.2021.250413

2021-12-30

Ukrainian Metrological Journal

Abstract:The pressure of electromagnetic radiation in the optical range is widely used to hold microparticles in a given place and control their movement. This is possible by focusing the laser radiation into an area with the dimension of several micrometers. The intensity of radiation in this area is large and sufficient to retain micro-particles in the laser beam and manipulate them. Nowadays, intensive research is underway on the use of microwave and terahertz radiation and the possibility of applying radiation pressure in these ranges. But in the microwave range, the focal spot dimension is much larger than in the optical one. Therefore, control of the objects whose dimensions are comparable to those of the focal spot using the radiation pressure requires very high power. For the objects with small dimensions, a small amount of radiation energy falls on them, and the acting force decreases. However, it is known that thin conductive fibers interact very strongly with microwave radiation. This can be used to levitate short thin metal fibers (vibrators), hold them in predicted place and control their position in space. The paper describes the measurements of the pressure of microwave radiation with a wavelength of 8 mm on thin copper fibers. Torsional balance is used for this purpose. In the metal case on a suspension from a tungsten fiber with a diameter of 8 microns there is located the rocker arm with 50 mm length with receiving elements in the form of system of copper fibers with a diameter of 300 microns and 15 mm length. Microwave radiation was directed to one of the receiving elements using a horn. The calibration of torsion balance, the measurement process, and the evaluation of the resulting error are described. The measurements gave the value of the efficiency factor of the radiation pressure Qpr = 4.86. This agrees satisfactorily with the results of calculations Qpr = 5.39. The difference is 10%.
Suppressing Mechanical Dissipation of Diamagnetically Levitated Oscillator Via Engineering Conductive Geometry

Han Xie,Yanan Li,Rui Li,Yinchun Leng,Yiming Chen,Lei Wang,Dingjiang Long,Xiang Bian,Chang-Kui Duan,Peiran Yin,Pu Huang,Jiangfeng Du

DOI: https://doi.org/10.1103/physrevresearch.5.013030

2023-01-01

Physical Review Research

Abstract:Diamagnetically levitated oscillators of millimeter and submillimeter size are emerging ultrasensitive sensors for gravitylike force and acceleration measurements. However, improving the levitation capability while keeping mechanical dissipation low remains an open challenge. Here, we propose and experimentally demonstrate an engineering conductive geometry scheme to efficiently reduce the mechanical dissipation of a diamagnetically levitated oscillator made of pyrolytic graphite. We show that with a specially designed conductive geometry, the eddy current damping is reduced, and the reduction factor increases as the engraving pattern being denser. Under high vacuum and room temperature, eddy current damping is the dominant contribution to mechanical dissipation, and we reduce it by a factor of 50 in the experiment. Our work opens up a new way to achieve diamagnetically levitated oscillator with ultralow mechanical dissipation and strong levitation capability, a candidate platform for studying a broad range of fundamental physics.
The levitation and driving performance of a contact-free manipulation device actuated by ultrasonic energy

He Li,Yu Wang,Yuanbo Li,Wei Sun,Yi Shen,Qingliang Zeng

DOI: https://doi.org/10.1016/j.ijmecsci.2022.107358

IF: 7.3

2022-07-01

International Journal of Mechanical Sciences

Abstract:To avoid the problems of wear, scratching, and contact pollution caused by traditional physical contact operations on high-precision materials or parts, a non-contact manipulation concept based on the near-field acoustic levitation effect and piezoelectric drive theory is proposed. The contact-free handling device can stably suspend the disc-shaped object and drive the object to rotate at a certain speed under the action of ultrasonic energy. The stable levitation capacity of the contact-free handling device relies on the vertical suspending force and horizontal restoring force derived from the W-type acoustic wave generated by the acoustic emission units. If the upper surface of the suspended disk has a specific configuration, a component driving force is generated when acoustic radiation is applied to it. To explore effective methods to improve the levitation effect, acoustic emission units were designed and fabricated, mathematical models of the suspending force and restoring force were built based on nonlinear acoustics and aerodynamics theories, and the influencing factors of these forces were investigated. In addition, a testing system for a contact-free manipulating device was fabricated to verify the levitation and driving performance using experimental methods.

engineering, mechanical,mechanics
Demonstration of an Ultra-Low-Threshold Phonon Laser with Coupled Microtoroid Resonators in Vacuum

Guanzhong Wang,Mingming Zhao,Yingchun Qin,Zhangqi Yin,Xiaoshun Jiang,Min Xiao

DOI: https://doi.org/10.1364/prj.5.000073

IF: 7.6

2017-01-01

Photonics Research

Abstract:We demonstrate an ultra-low-threshold phonon laser using a coupled-microtoroid-cavity system by introducing a novel coupling approach.The scheme exhibits both high optical quality factors and high mechanical quality factors.We have experimentally obtained the mechanical quality factor up to 18,000 in vacuum for a radialbreathing mode of 59.2 MHz.The measured phonon lasing threshold is as low as 1.2μW,which is～5 times lower than the previous result.
Nano-Newton electrostatic force actuators for femto-Newton-sensitive measurements: System performance test in the LISA Pathfinder mission

M. Armano,H. Audley,J. Baird,M. Bassan,P. Binetruy,M. Born,D. Bortoluzzi,E. Castelli,A. Cavalleri,A. Cesarini,V. Chiavegato,A. M. Cruise,D. Dal Bosco,K. Danzmann,M. De Deus Silva,R. De Rosa,L. Di Fiore,I. Diepholz,G. Dixon,R. Dolesi,L. Ferraioli,V. Ferroni,E. D. Fitzsimons,M. Freschi,L. Gesa,D. Giardini,F. Gibert,R. Giusteri,A. Grado,C. Grimani,J. Grzymisch,I. Harrison,M. S. Hartig,G. Heinzel,M. Hewitson,D. Hollington,D. Hoyland,M. Hueller,H. Inchauspé,O. Jennrich,P. Jetzer,B. Johlander,N. Karnesis,B. Kaune,N. Korsakova,C. J. Killow,L. Liu,J. A. Lobo,J. P. López-Zaragoza,R. Maarschalkerweerd,D. Mance,V. Martín,L. Martin-Polo,F. Martin-Porqueras,J. Martino,P. W. McNamara,J. Mendes,L. Mendes,N. Meshksar,J. Moerschell,M. Nofrarias,S. Paczkowski,M. Perreur-Lloyd,A. Petiteau,E. Plagnol,C. Praplan,J. Ramos-Castro,J. Reiche,F. Rivas,D. I. Robertson,G. Russano,L. Sala,P. Sarra,S. L. Schule-Walewski,J. Slutsky,C. F. Sopuerta,R. Stanga,T. Sumner,J. ten Pierick,D. Texier,J. I. Thorpe,D. Vetrugno,S. Vitale,G. Wanner,H. Ward,P. J. Wass,W. J. Weber,L. Wissel,A. Wittchen,C. Zanoni,P. Zweifel,LISA Pathfinder Collaboration

DOI: https://doi.org/10.1103/physrevd.109.102009

IF: 5.407

2024-05-23

Physical Review D

Abstract:Electrostatic force actuation is a key component of the system of geodesic reference test masses (TM) for the LISA orbiting gravitational wave observatory and in particular for performance at low frequencies, below 1 mHz, where the observatory sensitivity is limited by stray force noise. The system needs to apply forces of order 10−9 N while limiting fluctuations in the measurement band to levels approaching 10−15 N/Hz1/2 . We present here the LISA actuation system design, based on audio-frequency voltage carrier signals, and results of its in-flight performance test with the LISA Pathfinder test mission. In LISA, TM force actuation is used to align the otherwise free-falling TM to the spacecraft-mounted optical metrology system, without any forcing along the critical gravitational wave-sensitive interferometry axes. In LISA Pathfinder, on the other hand, the actuation was used also to stabilize the TM along the critical x axis joining the two TM, with the commanded actuation force entering directly into the mission's main differential acceleration science observable. The mission allowed demonstration of the full compatibility of the electrostatic actuation system with the LISA observatory requirements, including dedicated measurement campaigns to amplify, isolate, and quantify the two main force noise contributions from the actuation system, from actuator gain noise and from low frequency "in band" voltage fluctuations. These campaigns have shown actuation force noise to be a relevant, but not dominant, noise source in LISA Pathfinder and have allowed performance projections for the conditions expected in the LISA mission. https://doi.org/10.1103/PhysRevD.109.102009 © 2024 American Physical Society

astronomy & astrophysics,physics, particles & fields
Effects of Added Mass on Lead-Zirconate-Titanate (pzt) Thin-Film Microactuators in Aqueous Environments

Chuan Luo,Chen-Wei Yang,G. Z. Cao,I. Y. Shen

DOI: https://doi.org/10.1115/1.4034613

2013-01-01

Abstract:In this paper, we conduct experimental, theoretical, and numerical studies of a lead-zirconate-titanate (PZT) thin-film microactuator probe submerged in water. The major component of the actuator is a PZT diaphragm anchored on four silicon sidewalls. There is also silicon residue at the juncture of the diaphragm and the sidewalls due to imperfect etching processes. In the experimental study, frequency response functions of actuator displacement are measured via a laser Doppler vibrometer and a spectrum analyzer. The measurements show that the first natural frequency of the microactuator reduces from 80 kHz in air to 20 kHz when the microactuator is submerged in water. A viable explanation is that the surrounding water induces significant added mass to the microactuator. Estimation of the added mass based on theories in fluid mechanics successfully reconciles the predicted frequency to the vicinity of 20 kHz confirming the effects of added mass. Finite element models are also created to study how the silicon sidewalls and residue affect the added mass. Simulations show that presence of the sidewalls or residue would modify the fluid flow thus altering the added mass and natural frequency. In general, the finite element predictions agree well with the experimental measurements within 10% difference.
Stable Ion Radiation Pressure Acceleration with Intense Laser Pulses

B. Qiao,M. Geissler,S. Kar,M. Borghesi,M. Zepf

DOI: https://doi.org/10.1088/0741-3335/53/12/124009

IF: 2.532

2011-01-01

Plasma Physics and Controlled Fusion

Abstract:We have demonstrated the promising radiation pressure acceleration (RPA) mechanism of laser-driven ion acceleration at currently achievable laser and target parameters through a large number of two-dimensional particle-in-cell simulations and experiments. High-density monoenergetic ion beams with unprecedented qualities such as narrow-peaked spectrum, lower-divergence and faster energy-scaling are obtained, compared with the conventional target normal sheath acceleration. The key condition for stable RPA from thin foils by intense circularly polarized lasers has been identified, under which the stable RPA regime can be extended from ultrahigh intensities > 10(22) W cm(-2) to a currently accessible range 10(20)-10(21) W cm(-2). The dependences of the RPA mechanism on laser polarization, intensity and on the target composition and areal density have been studied.
A first demonstration of active feedback control and multi-frequency imaging techniques for kinetic inductance detectors

Maclean Rouble,Graeme Smecher,Michel Adamič,Adam Anderson,Peter S. Barry,Karia Dibert,Matt Dobbs,Kyra Fichman,Joshua Montgomery

2024-06-25

Abstract:RF-ICE is a signal processing platform for the readout of large arrays of superconducting resonators. Designed for flexibility, the system's low digital latency and ability to independently and dynamically set the frequency and amplitude of probe tones in real time has enabled previously-inaccessible views of resonator behaviour, and opened the door to novel resonator control schemes. We introduce a multi-frequency imaging technique, developed with RF-ICE, which allows simultaneous observation of the entire resonance bandwidth. We demonstrate the use of this technique in the examination of the response of superconducting resonators to variations in applied readout current and thermal loading. We observe that, used in conjunction with a conventional frequency sweep at sufficiently large amplitude to induce resonance bifurcation, the multi-frequency imaging technique reveals a resonator response which is not captured by the frequency sweep measurement alone. We demonstrate that equivalent resonant frequency shifts can be achieved using either thermal, optical, or readout loading, and use this equivalence to counteract a change in thermal loading by digitally modulating the readout current through a resonator. We develop and implement a proof-of-concept closed-loop negative electro-quasiparticle feedback algorithm which first sets and then maintains the resonant frequency of a lumped element kinetic inductance detector while the loading on it is varied. Although this simple implementation is not yet suitable to deploy at scale, it demonstrates the utility of this feedback technique to improve linearity while addressing amplifier distortion, resonator response non-uniformity, and crosstalk. It can be applied to kinetic inductors in non-bolometric operation, and sets the stage for future developments.

Instrumentation and Methods for Astrophysics
Practical Realization of the watt from Planck's Constant using Radiation Pressure

Brian J. Simonds,Kyle Rogers,Sven Schulze,David B Newell,Gordon Shaw,Johannes Wahl,Paul Williams,John H Lehman

DOI: https://doi.org/10.1088/1681-7575/ad844b

2024-10-09

Metrologia

Abstract:A primary force standard is implemented to realize the watt through Planck's constant by means of radiation pressure at the kilowatt level. The high amplification laser-pressure optic, or HALO, is a multiple reflection radiation pressure apparatus used for absolute radiometry of high-power lasers. In this work, a primary standard electrostatic force balance is used to measure the reflection-enhanced optical forces. With this configuration, the HALO is used to measure laser powers in the range of 100 W to 5000 W from a 1070 nm fiber laser. The expanded uncertainty of the 5 kW measurement is 0.12 %, which is both the lowest uncertainty multi-kW measurement and radiation pressure-based measurement to-date. The HALO result was validated against a thermal primary standard using a calibrated transfer standard at 2 kW. The degree of equivalence was 0.78 % ± 1.12 %, which demonstrates agreement within the uncertainties of these two primary standards.

instruments & instrumentation,physics, applied
Demonstration of Motion Transduction Based on Parametrically Coupled Mechanical Resonators

Pu Huang,Pengfei Wang,Jingwei Zhou,Zixiang Wang,Chenyong Ju,Zimeng Wang,Yang Shen,Changkui Duan,Jiangfeng Du

DOI: https://doi.org/10.1103/physrevlett.110.227202

IF: 8.6

2013-01-01

Physical Review Letters

Abstract:Universal sensing of the motion of mechanical resonators with high precision and low backaction is of paramount importance in ultraweak signal detection, which plays a fundamental role in modern physics. Here we present a universal scheme that mechanically transfers the motion of the resonator not directly measurable to the one that can be precisely measured using mechanical frequency conversion. Demonstration of the scheme at room temperature shows that both the motion imprecision and the backaction force are below the intrinsic level of the objective resonator, which agrees well with our theoretical prediction. The scheme developed here provides an effective interface between an arbitrary mechanical resonator and a high quantum efficient displacement sensor, and is expected to find extensive applications in highly demanding mechanical-based force measurements.
Radiation pressure excitation of test mass ultrasonic modes via three mode opto-acoustic interactions in a suspended Fabry-Perot cavity

Carl Blair,Sunil Susmithian,Chunnong Zhao,Fang Qi,Li Ju,David Blair

DOI: https://doi.org/10.48550/arXiv.1304.2116

2013-04-08

Optics

Abstract:Three-mode parametric-instabilities risk stable operation of gravitational-wave detectors. Instabilities occur through time varying radiation-pressure distributions, derived from beating between two optical modes, exciting mirror acoustic modes in Fabry-Perot cavities. Here we report the first demonstration of radiation-pressure driving of ultrasonic-acoustic modes via pairs of optical modes in gravitational-wave type optical cavities. In this experiment ~0.4W of TEM01 mode and ~1kW of TEM00 mode circulated inside the cavity, an ~181.6kHz excitation was observed with amplitude ~5E-13m. The results verify the driving force term in Braginsky's parametric instability feedback model. The interaction parametric gain was (3.8+/-0.5)E-3 and mass-ratio scaled opto-acoustic overlap 2.7+/-0.4.

Demonstration of Low Power Radiation Pressure Actuation for Control of Test Masses

Radiation Pressure Actuation of Test Masses

A simple table-top demonstration of radiation pressure on a macroscopic object

A Contactless Methodology of Picking Up Micro-Particles from Rigid Surfaces by Acoustic Radiation Force

Feedback control and characterization of a microcantilever using optical radiation pressure

Radiation-Pressure-Mediated Control of an Optomechanical Cavity

Optical power meter using radiation pressure measurement

A Hybrid Photovoltaic/flexoelectric Actuation Mechanism Applied to Precision Actuation and Vibration Control of Beams

Radiation pressure approach to the measurement of single-pulse microwave power

Implementation of Electrostatic Actuators for Suspended Test Mass Control

Measurement of microwave radiation pressure on thin metal fibers

Suppressing Mechanical Dissipation of Diamagnetically Levitated Oscillator Via Engineering Conductive Geometry

The levitation and driving performance of a contact-free manipulation device actuated by ultrasonic energy

Demonstration of an Ultra-Low-Threshold Phonon Laser with Coupled Microtoroid Resonators in Vacuum

Nano-Newton electrostatic force actuators for femto-Newton-sensitive measurements: System performance test in the LISA Pathfinder mission

Effects of Added Mass on Lead-Zirconate-Titanate (pzt) Thin-Film Microactuators in Aqueous Environments

Stable Ion Radiation Pressure Acceleration with Intense Laser Pulses

A first demonstration of active feedback control and multi-frequency imaging techniques for kinetic inductance detectors

Practical Realization of the watt from Planck's Constant using Radiation Pressure

Demonstration of Motion Transduction Based on Parametrically Coupled Mechanical Resonators

Radiation pressure excitation of test mass ultrasonic modes via three mode opto-acoustic interactions in a suspended Fabry-Perot cavity