Abstract:In this paper, G-phase precipitation and the resulting hardening effect on Fe-20Cr-3Ni-1Mn-3Si ferritic alloys by the addition of Ti, Nb, Ta and Zr were individually studied by electron microscopy and atom probe tomography, combined with thermodynamic and first principle calculations. The high resolution scanning electron and transmission electron microscopy observations confirmed that four kinds of Ni16M6Si7 (M = Ti, Nb, Ta and Zr) Gphase particles were distributed uniformly in the matrix of the four alloys aged at 560-860 degrees C. The 3D-APT results revealed the formation of the four different nanoscale precipitates, with the highest number density (6.05 x 10(23)m(-3)) and smallest radius (1.64 +/- 0.45 nm) in the Ti added alloy. The nanoscale sized precipitates stability (similar to 3 nm for Ti added alloy; similar to 5 nm for Nb added alloy and Zr added alloy; similar to 25 nm for Ta added alloy) was attributed to their particular cube-cube orientation relationships, which led to a very low interfacial energy. The effects of the G-phase on precipitation hardening and quasi steady-state deformation resistance were examined. The 560 degrees C-aging hardening experiments suggested a rapid precipitation process of the nano-particles. The peak hardness values of the four alloys are in the descending order: Ti- >> Nb > Ta- >> Zr. The 660 degrees C quasi steady-state deformation experiments showed threshold stresses of 110 and 140 MPa in cases of the Nb and Ti added alloys, which were higher than that of the previously reported B2-NiAl strengthened steels and commercial heat-resistant steels. By using the formation of nanoscale G-phase precipitates, a new ferritic steel family with very high strength and creep resistance has been proposed. Further alloy optimization is in progress.

Precipitate Behavior in Fe–20Cr–30Ni–2Nb Austenitic Heat-Resistant Steel

Precipitation Behavior of Fe2Nb Laves Phase on Grain Boundaries in Austenitic Heat Resistant Steels

Introduction Of L1(2)-Ordered Precipitation To Alumina-Forming Austenitic Heat-Resistant Steels With Low Ni Content

Effect of Al addition on Nb-rich phase precipitation behavior in ferritic stainless steel

Effect of Nb and La on Precipitates, Yield Strength and Toughness of FeCrAl Alloy

Study of Transformation Characteristics and Nano-Scale Precipitation in Nb Microalloyed Steel

Introduction of L12-Ordered Precipitation to Alumina-Forming Austenitic Heat-Resistant Steels with Low Ni Content

Precipitate Evolution in 22Cr25NiWCuCo(Nb) Austenitic Heat-Resistant Stainless Steel during Heat Treatment at 1200 °C

Impact of L1(2)-Ordered Precipitation on the Strength of Alumina-Forming Austenitic Heat-Resistant Steels

Eutectic precipitates and microstructure of electroslag remelted 15Cr–22Ni austenitic heat-resistant steel with varying Nb contents

Effect of Zr Addition on the Stability of Precipitated Laves Phase and Mechanical Properties of Fe–Cr–Al-based Alloys at High Temperatures

Effect of Interstitial Solutes on Precipitation Behavior of 9–12% Chromium Ferritic Steels

Effect of ferrochromium (FeCr) and ferroniobium (FeNb) alloys on inclusion and precipitate characteristics in austenitic stainless steels

Effect of Nb and B on the Precipitation Behaviors in Al-Ti-Nb Balanced Ratio Ni-Based Superalloy: A Phase-Field Study

Microstructural Evolution and Precipitation Strengthening In a New 20Cr Ferritic Trial Steel

Thermodynamic calculations of precipitation behavior in Nb microalloyed steels

Design of Novel Precipitate-Strengthened Al-Co-Cr-Fe-Nb-Ni High-Entropy Superalloys

A Novel Ferritic Steel Family Hardened by Intermetallic Compound G-phase

Phase precipitation behavior of rapidly quenched ternary La–Fe–B alloy and the effects of Nd substitution

Precipitation behavior in G-phase strengthened ferritic stainless steels