Abstract:Analytical pyrolysis was conducted to study a relative comparison of the hydrocarbon and greenhouse gas emissions of three foundry sand binders as follows: (a) conventional phenolic urethane resin, (b) biodiesel phenolic urethane resin, and (c) collagen-based binder. These binders are used in the metal casting industry for making cores that are used to create internal cavities within castings. In this study, the core samples were flash pyrolyzed in a Curie-point pyrolyzer at 920 degrees C with a heating rate of about 3000 degrees C/sec. This simulated some key features of the fast heating conditions that the core binders would experience at the metal-core interface when molten metal is poured into green sand molds. The core samples were also pyrolyzed in a thermogravimetric analyzer (TGA) from ambient temperature to 1000 degrees C with a heating rate of 30 degrees C/min, and this simulated key features of the slow heating conditions that the core binders would experience at distances that are further away from the metal-core interface during casting cooling. Hydrocarbon emissions from flash pyrolysis were analyzed with a gas chromatography-flame ionization detector, while hydrocarbon and greenhouse gas (CO and CO2) emissions from TGA pyrolysis were monitored with mass spectrometry. The prominent hazardous air pollutant emissions during pyrolysis of the three binders were phenol, cresols, benzene, and toluene for the conventional phenolic urethane resin and biodiesel resin, and they were benzene and toluene for the collagen-based binder. It was also found that volatile organic compound and polycyclic aromatic hydrocarbon emissions considerably decreased in order from conventional phenolic urethane resin to biodiesel resin to collagen-based binder. These results have shown some similarity with those for stack emission testing conducted at demonstration scale and/or full-scale foundries, and the similar trends in the two sets of results offered promise that bench-scale analytical pyrolysis techniques could be a useful screening tool for the foundries to compare the relative emissions of alternative core binders and to choose proper materials in order to comply with air-emission regulations.

Diminishing Hazardous Air Pollutant Emissions from Pyrolysis of Furan No-Bake Binders Using Methanesulfonic Acid As the Binder Catalyst

Hazardous Air Pollutant Formation from Pyrolysis of Typical Chinese Casting Materials.

Characterization of hydrocarbon emissions from green sand foundry core binders by analytical pyrolysis

[Application of Analytical Pyrolysis in Air Pollution Control for Green Sand Casting Industry].

Comparative Analysis Of Hazardous Air Pollutant Emissions Of Casting Materials Measured In Analytical Pyrolysis And Conventional Metal Pouring Emission Tests

Study on the Mechanisms of Hazardous Air Pollutant Emissions from Green Sand Casting

Evaluation of Volatile Hydrocarbon Emission Characteristics of Carbonaceous Additives in Green Sand Foundries.

Characterization of Pyrolysis Products from a Biodiesel Phenolic Urethane Binder.

In Situ Mass Spectrometric Analysis on Zeolite-Catalyzed Pyrolysis of Furanic Compounds: The Role of Reactive Intermediates

Effect of High-Density Polyethylene Pyro-Oil Modification on Chemical, Rheological, and Damping Properties of Binders

Fast co-pyrolysis of lignin with spent bleaching clay into monocyclic aromatic hydrocarbons over a novel low-cost composite catalyst

Study of bifunctional calcium-based catalysts for PCDD/Fs removal in medical waste pyrolysis-combustion process

A Key Alternative for Reducing Harmful Emissions in Molding and Core-Making Technologies

Performance of Oil-Absorbing Organogel Polystyrene-Stearyl Methacrylate As a Fume Suppressant of Asphalt Binder

A Furan-based Phosphaphenanthrene-containing Derivative As a Highly Efficient Flame-retardant Agent for Epoxy Thermosets Without Deteriorating Thermomechanical Performances

New Green Bio-Based Binder to Reduce the Poisonous and Harmful Gases Generated from the Combustion of Pyrotechnics

Catalytic Pyrolysis Vapor Upgrading of Corncob into Furans over Pyrolysis-Comprehensive Two-Dimensional Gas Chromatography/Mass Spectrometry: Significance of Catalyst and Temperature

Industrial by-products-derived binders for in-situ remediation of high Pb content pyrite ash: Synergistic use of ground granulated blast furnace slag and steel slag to achieve efficient Pb retention and CO 2 mitigation

In Situ Catalytic Cracking of Sawdust Fast Pyrolysis Vapors

Efficient ex-situ catalytic upgrading of biomass pyrolysis vapors to produce methylfurans and phenol over bio-based activated carbon

Pore Structure Development of In-Situ Pyrolyzed Coals for Pollution Prevention in Iron Foundries