Abstract:Carbon nanotube/continuous carbon fiber reinforced poly(ethylene terephthalate) (CNT/CCF/PET) composites are prepared by melt impregnating. The effects of CF and CNT content on the mechanical properties, melt and crystallization behaviors, and submicroscopic morphology of CNT/CCF/PET composites are studied. The tensile test results show that the increase of CF and the addition of appropriate amount of CNT improved the tensile strength and tensile modulus of the composites. When the content of CNT is 1.0 wt% and the content of CF is 56 wt%, the properties of the composites are the best, with tensile strength of 1728.7 MPa and tensile modulus of 25.1 GPa, which is much higher than that of traditional resin matrix composites. The results of dynamic mechanical analysis (DMA) show that the storage modulus of the composites increased with the increase of CF and CNT content. In particular, the addition of CNT greatly reduced the loss modulus of the composites. Morphological analysis show that the addition of CNT improved the fiber–matrix interface of the composite, which changes from fiber pull-out and fracture failure to fiber matrix fracture failure, and the fiber matrix interface is firmly bonded. In addition, there are polymer coated CNT protrusions on the surface of the fiber was observed. The results of differential scanning calorimetry (DSC) show that the melting temperature and crystallization temperature of the composites increased with the increase of CF content. The addition of CNT had little effect on the melting temperature of the composites, but it further improved the crystallization temperature of the composites. The effect of CNT content on the crystallization kinetics of the composites is studied. The non-isothermal crystallization kinetics of the composites is described by Jeziorny's improved Avrami equation. The results show that CNT has a great influence on the crystallization type of the composites. As a nucleating agent, CNT has obvious heterogeneous nucleation effect in the composites, which improves the crystallization rate of PET.

Effect of Proton Irradiation on Mechanical Properties of Low‐density Polyethylene/multiwalled Carbon Nanotubes Composites

Preparation of Isotactic Polypropylene-Grafted Multiwalled Carbon Nanotubes (Ipp-G-mwnts) by Macroradical Addition in Solution and the Properties of Ipp-G-Mwnts/Ipp Composites

Influence of Wall Number and Surface Functionalization of Carbon Nanotubes on Their Antioxidant Behavior in High Density Polyethylene

Reducing Dispersity of Mechanical Properties of Carbon Fiber/epoxy Composites by Introducing Multi-Walled Carbon Nanotubes

Radiation Effects on Polyethylene and Polypropylene by Electrons and Protons

The Effects of Irradiation Cross-Linking on the Thermal Degradation and Flame-Retardant Properties of the Hdpe/Eva/Magnesium Hydroxide Composites

Proton Beam Modification of Isotactic Polypropylene

Irradiation Treatment of Multiwalled Carbon Nanotubes and Its Effect on the Thermal Properties of Their Composites with Epoxy Resin

Proton irradiation-induced changes in the tribological performance of polyimide composites

Polyethylene/maleic Anhydride Grafted Polyethylene/organic‐montmorillonite Nanocomposites. I. Preparation, Microstructure, and Mechanical Properties

Melt extrudate swell behavior of multi‐walled carbon nanotubes filled‐polypropylene composites

Study on the Microstructure of Polyether Ether Ketone Films Irradiated with 170 keV Protons by Grazing Incidence Small Angle X-ray Scattering (GISAXS) Technology

Effect of Multi-Walled Carbon Nanotubes on the Properties of Polyoxymethylene

Fabrication and characterization of microwave cured high-density polyethylene/carbon nanotube and polypropylene/carbon nanotube composites

The effect of CNT grafting on the mechanical properties of the UHMWPE fiber/HDPE composite

Effect of NH2-MWCNTs sprayed carbon fiber on the mechanical properties of carbon fiber reinforced polycarbonate composite for lightweight structural applications

Influence of Gamma Irradiation on High Density Polyethylene/ethylene‐vinyl Acetate/clay Nanocomposites

Mechanical Properties, Melting and Crystallization Behaviors, and Morphology of Carbon Nanotubes/Continuous Carbon Fiber Reinforced Polyethylene Terephthalate Composites

Effect of ultraviolet irradiation on strength and toughness of composites of poly(lactic acid) and poly(butylene adipate-co-terephthalate) with different mass ratio

Investigation of the mechanical and thermal stability of ultra-high molecular weight polyethylene by using amide-multi-walled carbon nanotubes as a reinforcement material

Carbon fiber coating with MWCNT in the presence of polyethyleneimine of different molecular weights and the effect on the interfacial shear strength of thermoplastic and thermosetting carbon fiber composites