Abstract:A new lower tungsten divertor has been developed and installed in the EAST superconducting tokamak to replace the previous graphite divertor with power handling capability increasing from <2 MW m−2 to ∼10 MW m−2, aiming at achieving long-pulse H-mode operations in a full metal wall environment with the steady-state divertor heat flux of ∼10 MW m−2. A new divertor concept, ‘corner slot’ (CS) divertor, has been employed. By using the ‘corner effect’, a strongly dissipative divertor with the local buildup of high neutral pressure near the corner can be achieved, so that stable detachment can be maintained across the entire outer target plate with a relatively lower impurity seeding rate, at a separatrix density compatible with advanced steady-state core scenarios. These are essential for achieving efficient current drive with low-hybrid waves, a low core impurity concentration and thus a low loop voltage for fully non-inductive long-pulse operations. Compared with the highly closed small-angle-slot divertor in DIII-D, the new divertor in EAST exhibits the following merits: (1) a much simpler geometry with integral cassette body structure, combining vertical and horizontal target plates, which are more suitable for actively water-cooled W/Cu plasma facing components, facilitating installation precision control for minimizing surface misalignment, achieving high engineering reliability and lowering the capital cost as well; (2) it has much greater flexibility in magnetic configurations, allowing for the position of the outer strike point on either vertical or horizontal target plates to accommodate a relatively wide triangularity range, δ l = 0.4–0.6, thus enabling to explore various advanced scenarios. A water-cooled copper in-vessel coil has been installed under the dome. Five supersonic molecular beam injection systems have been mounted in the divertor to achieve faster and more precise feedback control of the gas injection rate. Furthermore, this new divertor allows for double null divertor operation and slowly sweeping the outer strike point across the horizontal and vertical target plates to spread the heat flux for long-pulse operations. Preliminary experimental results demonstrate the ‘corner effect’ and are in good agreement with simulations using SOLPS-ITER code including drifts. The EAST new divertor provides a test-bed for the closed divertor concept to achieve steady-state detachment operation at high power. Next step, a more closed divertor, ‘sharp-cornered slot’ divertor, building upon the current CS divertor concept, has been proposed as a candidate for the EAST upper divertor upgrade.

Study on the Operation Safety of Hts Current Leads in East Device

Overview of Experimental Results on the HL-2A Tokamak

OV / 4-3 1 Overview of Experimental Results on HL-2 A

Development of a Conduction-Cooled HTS SMES

Fully Active Cooled In-vessel Components of EAST Tokamak

Power Balance Investigation in Long-Pulse High-Performance Discharges with ITER-like Tungsten Divertor on EAST

Development of HTS Current Leads for the ITER Project

Physics Design of New Lower Tungsten Divertor for Long-Pulse High-Power Operations in EAST

Cold Performance Tests of the ITER 68 Ka HTS Current Lead Prototypes

Test Results of ITER 52-Ka HTS Current Lead Prototypes

Development of Testing Device for Critical Current Measurements for HTS/LTS

Advances in the Long-Pulse Steady-State High Beta H-mode Scenario with Active Controls of Divertor Heat and Particle Fluxes in EAST

Preliminary Design of Water-Cooling System for Liquid Metal Divertor Target Test Module in EAST

The Cooling and Safety Design of a Pair of Binary Leads for the MICE Coupling Magnets

Study on Heat Leakage of Current Leads of 300 Kva HTS Transformer

Recent EAST Experimental Results and Systems Upgrade in Support of Long-Pulse Steady-State Plasma Operation

Design for In-Field Critical Current Measurement System With 102 Mm 15 T Background Magnet

Quench Detection of 20-kA HTS Current Leads Using Distributed Optical Fibers

Test Facility and Results of ITER PF4 Current Leads

Modelling and analysis of quench in the 15-kA HTS conductor

Influence of Critical Current Distribution on Operation, Quench Detection and Protection of HTS Pancake Coils