Abstract:Solid-state lithium metal batteries attract much attention for their high theoretical specific capacity and safety. However, the poor interfacial combination between the solid electrolyte (SE) and Li anode usually results in unavoidable growth of Li dendrites and interfacial side reactions. In this work, we propose a simple and effective strategy to modify the interface of the electrolyte/Li anode by scraping a graphite layer on the electrolyte surface facing the anode. The graphite-modified solid electrolyte (G-SE) has a high electrochemical potential window exceeding 4.6 V and high ion conductivity of 3.08 × 10–4 S·cm–2 at ambient temperature. This G-SE membrane is suitable for high-voltage solid-state lithium metal batteries, the assembled NCM622/G-SE/Li cell shows an initial capacity of 160 mAh/g at 0.5 C and a retention capacity of 100 mAh/g after 200 cycles. The good electrochemical performance is attributed to the graphite interfacial modification; the graphite coating and Li can spontaneously react to form a LiC6 layer, which improves the SE/Li interfacial combination and suppresses the growth of lithium dendrites and interfacial side reactions.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acssuschemeng.0c05153?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acssuschemeng.0c05153</a>.EDS point analysis for the Li sheet after cycling (Figure S1); enlarged images of <a class="internalNav" href="#fig6">Figure </a><a class="internalNav" href="#fig6">6</a>a (Figure S2); battery case with test window (Figure S3); C 1s XPS spectrum of the Li sheet with graphite after cycling (Figure S4); lithium metal optical microscope image (Figure S5); digital photo of the lithium metal after 24 h of lithium/G-SE/lithium battery shelving (Figure S6); and the ion transport number calculation table (Table S1) (<a class="ext-link" href="/doi/suppl/10.1021/acssuschemeng.0c05153/suppl_file/sc0c05153_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Investigation of Graphite-based Interfacial Engineering in the Solid-State Lithium Metal Batteries with a Garnet-Structured Solid Electrolyte

Facile Surface Modification Method to Achieve an Ultralow Interfacial Resistance in Garnet-Based Li Metal Batteries

Garnet Electrolyte with an Ultralow Interfacial Resistance for Li-Metal Batteries

(Invited) Achieving High Areal Capacity and Extreme Critical Current Densities through Tailored Garnet Solid Electrolyte Structures

Drawing a Soft Interface: An Effective Interfacial Modification Strategy for Garnet-Type Solid-State Li Batteries

Dual Interface Layers for Solid-State Li Metal Battery with Low Interfacial Resistance and Small Polarization Based on Garnet Electrolyte

High‐Performance Garnet‐Type Solid‐State Lithium Metal Batteries Enabled by Scalable Elastic and Li+‐Conducting Interlayer

Interfacial Modification of Li/Garnet Electrolyte by a Lithiophilic and Breathing Interlayer

A Facile and Low-Cost Wet-Chemistry Artificial Interface Engineering for Garnet-Based Solid-State Li Metal Batteries

High-performance garnet solid-state battery enabled by improved interfaces

Enhanced Cathode/Electrolyte Interface in Solid-state Li-metal Battery based on Garnet-type Electrolyte

An in situ-formed high lithiophilic solid lubricant interface layer for garnet-based solid-state lithium metal batteries

An in Situ Formed Mosaic Li7Sn3-LiF Interface Layer for High-Rate and Long-Life Garnet-Based Lithium Metal Batteries.

Tuning the Anode–Electrolyte Interface Chemistry for Garnet‐Based Solid‐State Li Metal Batteries

Excellent Li/Garnet Interface Wettability Achieved by Porous Hard Carbon Layer for Solid State Li Metal Battery

Improving Bulk and Interfacial Lithium Transport in Garnet-Type Solid Electrolytes through Microstructure Optimization for High-Performance All-Solid-State Batteries

Smart Construction of an Intimate Lithium | Garnet Interface for All‐Solid‐State Batteries by Tuning the Tension of Molten Lithium

Restrained Li|Garnet Interface Contact Deterioration Manipulated by Lithium Modification for Solid‐State Batteries

Garnet-Based Solid Li-Metal Batteries Operable under High External Pressure with HCOOH-Induced Electron-Blocking and Lithiophilic Interlayer

Li/Garnet Interface Optimization: An Overview

Highly Efficient Interface Modification between Poly(Propylene Carbonate)-Based Solid Electrolytes and a Lithium Anode by Facile Graphite Coating