Abstract:Background Pulmonary function and respiratory pattern exams are essential for the diagnosis of various diseases, such as COPD and asthma. Most equipment used in these exams is not sterilized, making the use of respiratory filters necessary for biological protection of the evaluated individual. However, the use of filters with high air resistance can alter the measurement of airflow and air volume during these evaluations. Thus, analyzing the influence of this resistance is important to ensure that the results of these exams can be reliable. Objectives To analyze the influence of the resistance of a respiratory filter on the flow and volume values collected in an innovative equipment used for the examination of the human respiratory pattern. Methods This is an experimental study. The measurement system consists of an Active Servo Lung (ASL) 5000 human breathing simulator; a respiratory filter holder for the KOKO spirometer; a respiratory filter for spirometry; and the Respiratory Diagnostic Assistant (RDA) device, developed by the LINDEF/UFPE laboratory for the evaluation of the respiratory pattern. The ASL 5000 was configured to simulate the normal respiratory pattern of a healthy adult individual. The settings were: respiratory frequency = 10 bpm; inspiratory time 2 s, expiratory time 4 s, I:E ratio = 1:2; tidal volume = 0.5L; airway resistance = 3cmH2O; lung compliance = 100mL/cmH2O; and muscle pressure = 15cmH2O. The breathing simulation was programmed to occur for 3 minutes, and thus, the ASL 5000 produced a total of 30 respiratory cycles, of which the flow and volume curves and respiratory pattern parameters were recorded by the RDA. This same procedure was performed twice, once with the presence of the filter membrane inside the filter holder, and another time without the presence of the filter membrane. The results were subsequently analyzed by the RDA Analysis software. Results With the addition of the filter to the system, there was a decrease from 84.46 L/min to 79.76 L/min in inspiratory flow and from 90.25 L/min to 85.76 L/min in expiratory flow, with a consequent reduction from 1323.63 mL to 1285.26 mL in inspiratory tidal volume and from 1293.73 mL to 1270.96 mL in expiratory tidal volume. Conclusion By comparing the mean values of inspiratory and expiratory flow and volume in the simulation of a basal respiration, it can be inferred that the resistance imposed by the filter added to the system produced considerable decreases in inspiratory and expiratory flow and volume values. Implications The differences obtained in this result are useful for compensation adjustments in the RDA software, aiming to correct this resistance imposed by the filter membrane, necessary during collection. Thus, this result will contribute to ensuring a respiratory pattern exam as close as possible to what the evaluated patient actually presents. It also brings reflection on the need to correct the volume and flow values obtained by other software responsible for the processing of respiratory pattern and pulmonary function data, which require the use of respiratory filters in their execution.

Estimating the Dead Space Volume Between a Headform and N95 Filtering Facepiece Respirator Using Microsoft Kinect

Simulated effects of head movement on contact pressures between headforms and N95 filtering facepiece respirators-part 1: headform model and validation.

Simulated effects of head movement on contact pressures between headforms and N95 filtering facepiece respirators part 2: simulation.

Face anthropometry for filtering facepiece respirators: analysis of the association between facial dimensions and respirator fit

Toward Respiratory Assessment Using Depth Measurements from a Time-of-Flight Sensor

Embedded Electronic Sensor for Monitoring of Breathing Activity, Fitting and Filter Clogging in Reusable Industrial Respirators

A Physical Analog to Assess Surgical Face Mask Air Flow Resistance During Tidal Ventilation

Computational fluid dynamics study of respiratory mask for neonatal resuscitation

Design of customizable personal protective equipment for 3-D printing: Performance evaluation of N95 respirators using computational fluid dynamics

Novel Smart N95 Filtering Facepiece Respirator with Real-time Adaptive Fit Functionality and Wireless Humidity Monitoring for Enhanced Wearable Comfort

Reliable Breathing Tracking With Wearable Mask Device

Numerical simulation of aerosol permeation through microstructure of face masks coordinating with x-ray computed tomography images

A special face mask with integrated angle meter to optimize the head position for bag-valve-mask ventilation—a prospective simulated proof-of-concept study

An apparatus for nondestructive and rapid comparison of mask approaches in defense against infected respiratory aerosols

High-Mechanical-Resolution Pressure Sensor Based on Melt-Blown Fibers in Integrated Wearable Mask for Respiratory Monitoring

Towards the Instrumentation of Facemasks Used as Personal Protective Equipment for Unobtrusive Breathing Monitoring of Workers

Volumeter: 3D human body parameters measurement with a single Kinect

Experimental and Numerical Investigation of the Wake Flow of a Human-Shaped Manikin: Experiments by PIV and Simulations by CFD

Three-Dimensional Analysis of Particle Distribution on Filter Layers inside N95 Respirators by Deep Learning

0308 Non-Contact Sleep Monitoring with a Depth Camera: Morphology Similarity Between a Touchless Flow Signal and RIPflow

IMPACTS OF AIR RESISTANCE IMPOSED BY RESPIRATORY FILTERS ON VOLUME AND FLOW VALUES DURING SIMULATED RESPIRATORY PATTERN