Abstract:To achieve low cost, high rate and attractive capacity of CO2 adsorption by using ionic liquids (IL), a new mesostructured ionogel, pyridine-containing anion functionalized IL tetrabutylphosphonium 2-hydroxypyridine ([P-4444][2-Op]) encapsulated silica MCM-41 (noted as PM-w), is fabricated by loading the IL [P-4444][2-Op] with multiple active sites into porous silica MCM-41 through a simple moisturecontrolled impregnation-evaporation method. Allosteric effect driven gas sorption on the electronegative oxygen and nitrogen atoms of the nanoconfined IL [P-4444][2-Op] makes it take no more than 2 min for the ionogel PM-5 to achieve the 90% of saturated adsorption capacity. The corresponding adsorption rate is 30 times faster than that of the bulk IL. The ionogel PM-5 with the low IL loading of 5.0% shows the highest CO2 adsorption capacity up to 1.21 mmol (g-ionogel)(-1) (14.89 mmol (g-IL)(-1)) at 50 degrees C in a gas mixture with N-2, which is 9.25 times higher than that of the pure IL. Its excellent cyclic stability of more than 96% of the initial CO2 uptake repeatedly displayed after performing 10 cycles of adsorption-desorption tests. The enhanced thermal stability up to 450 degrees C in N-2 is observed for the low loading ionogels since the strong interfacial layering of the IL prefers to dot the silica nanopores as monomolecular islands. Reversely, the high loading IL may aggregate into nanosized clusters that recover the poor thermal stability of the bulk IL. Reasonable decreases in their surface area, pore volume and pore size are observed with the IL loading up to 45%. They still exhibit highly ordered hexagonal mesostructures. The features of low loading and cost, rapid adsorption, high capacity and excellent cyclic stability make the ionogel PM-5 a competitive candidate in CO2 capture from flue gas.

Novel CO2-capture derived from the basic ionic liquids orientated on mesoporous materials.

Preparation and Co2 Sorption/Desorption of N-(3-Aminopropyl) Aminoethyl Tributylphosphonium Amino Acid Salt Ionic Liquids Supported into Porous Silica Particles

Unveiling the Porosity Effect of Superbase Ionic Liquid-Modified Carbon Sorbents in CO 2 Capture from Air

Efficient Capture of CO2 from Flue Gas at High Temperature by Tunable Polyamine-Based Hybrid Ionic Liquids

Amine-functionalized ionic liquids for CO2 capture

CO2 Adsorption by Polyamine-Based Protic Ionic Liquid-Functionalized Mesoporous Silica: Regenerability and Influence of Flue Gas Contaminants

State of the art of ionic liquid‐modified adsorbents for CO 2 capture and separation

First-principles-guided Design of Ionic Liquids for CO2 Capture

Poly(Ionic Liquid)-Based Nanocomposites and Their Performance in Co2 Capture

CO2 capture using silica-immobilized dicationic ionic liquids with magnetic and non-magnetic properties

Alkylimidazolium-based ionic liquids with tailored anions and cations for CO2 capture

Highly Efficient and Reversible Carbon Dioxide Capture by Carbanion-Functionalized Ionic Liquids.

Reversible Co2 Capture by Conjugated Ionic Liquids Through Dynamic Covalent Carbon-Oxygen Bonds

CO2 Capture with Complex Absorbent of Ionic Liquid and Water

Designed imidazolium-based ionic liquids to capture carbon dioxide from natural gas

Novel Fluid Ionic Liquid Composites with Self-Assembled Porosity and Chemical Sites for Facilitating CO2 Separation

Novel Fluid Ionic Liquid Composites with Self-Assembled Porosity and Chemical Sites for Facilitating CO 2 Separation

Designing of Anion-Functionalized Ionic Liquids for Efficient Capture of So2 from Flue Gas

Unique allosteric effect-driven rapid adsorption of carbon dioxide in a newly designed ionogel [P4444][2-Op]@MCM-41 with excellent cyclic stability and loading-dependent capacity

Ionic Liquid Membrane for Carbon Capture and Separation

Carbon Dioxide Solubility in Three Bis Tri (Fluromethylsulfonyl) Imide-Based Ionic Liquids