Abstract:In this study, different contents of rare earth elements with high solid solubility (Gd and Dy) were added into Mg and fabricated through homogenization and hot extrusion processes that enable few second phase formation to efficaciously inhibit the galvanic corrosion. The microstructure and phase characterization of the as-extruded Mg-Gd-Dy-Zr alloys were analyzed by scanning electron microscopy, electron backscattered diffraction, and X-ray diffraction. The in vitro biodegradation behavior of the as-extruded Mg-Gd-Dy-Zr alloys was investigated via the electrochemical measurement and immersion test. The results revealed that all the as-extruded alloys with different RE additions exerted fully recrystallized microstructures. The average grain size was appropriately 20 mu m to 30 mu m for all alloys and gradually increased by adding more RE. Only a few tiny second-phase particles less than 5 mu m dispersed for all the samples and the volume fraction of particles increased slightly with the increase in RE content. The as-extruded Mg-Gd-Dy-Zr alloys with low RE content (GD0.6) allowed for a satisfactory corrosion resistance in Hank's solution with a controlled corrosion rate less than 0.5 mm/year, which is considered as the tolerance limit for the corrosion rate of orthopedic implants. This study provides a cost-effective choice for promoting biodegradable magnesium alloys for potential orthopedic applications with low rare earth content in Mg alloys.

Microstructure, Mechanical and Corrosion Properties of Mg–Dy–Gd–Zr Alloys for Medical Applications

Mechanical properties and corrosion behavior of Mg-Gd-Ca-Zr alloys for medical applications

Mechanical and Corrosion Properties of Mg-Based Alloys with Gd Addition

Mechanical and Corrosion Properties of Binary Mg–Dy Alloys for Medical Applications

Mechanical properties, corrosion, and biocompatibility of Mg-Zr-Sr-Dy alloys for biodegradable implant applications

The Influence of Gd Content on the Microstructure, Mechanical Properties, Corrosion Behavior and Corrosion Film Deposition Mechanisms of As-Extruded Mg–Zn–Mn–Sr–Gd Alloys for Biomedical Applications

Enhanced Mechanical Properties and Corrosion Resistance by Minor Gd Alloying with a Hot-Extruded Mg Alloy

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

In Vitro Corrosion Performance of As-Extruded Mg-Gd-Dy-Zr Alloys for Potential Orthopedic Applications

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Microstructure Characteristics and Degradation Behaviors of Medical Rare-Earth Mg-10.6Gd-0.3Ag-x(Y/Zn) Alloys in Vitro

Effect of Mn Content on Microstructure, Mechanical Properties, and Corrosion Behavior of Mg-Zn-Gd-Y Alloy

Microstructure, Mechanical Properties, and Corrosion Behavior of Degradable Mg-Al-Cu-Zn-Gd Alloys

Corrosion behavior and mechanical degradation of as-extruded Mg-Gd-Zn-Zr alloys for orthopedic application

Characterization and Properties of Mg-xGd-1.5Nd-0.5Zn-0.5Zr Alloys for Biodegradation Applications.

Influence of Ageing Treatment on Microstructure, Mechanical and Bio-Corrosion Properties of Mg-Dy Alloys

Tailoring Corrosion Behavior and Mechanical Property of Mg-6Zn Alloy with Varying Dy Contents for Biological Application

Microstructures and mechanical properties of as-cast Mg–5Y–3Nd–Zr–xGd (x=0, 2 and 4wt.%) alloys

In Vitro Biodegradability of Mg–2Gd– X Zn Alloys with Different Zn Contents and Solution Treatments

Structural characteristics and corrosion behavior of biodegradable Mg-Zn, Mg-Zn-Gd alloys

Biocorrosion Behavior and Cytotoxicity of a Mg–Gd–Zn–Zr Alloy with Long Period Stacking Ordered Structure