Abstract:Laser ultrasound (LU) is a contactless and couplant-free remote non-destructive (NDE) technique, which uses lasers for ultrasonic generation and detection rather than conventional piezoelectric transducers. For a transducer, an important characteristic is the directivity , the angle-dependent amplitude of the ultrasonic waves generated in the material. In the non-destructive thermoelastic regime, LU source has been widely modelled as a surface force dipole. However, the directivity of LU in more complex material, where there is an increasing demand for NDE, such as carbon fibre reinforced plastic (CFRP), is yet to be understood. In the current paper, a finite element (FE) modelling methodology to obtain the directivity of LU in complex material is presented. The method is applied to a conductive isotropic material (aluminium, Al) for validation against an existing analytical solution and then applied to a heterogeneous anisotropic material (carbon-fibre reinforced plastic, CFRP). To get the directivity of a specific wave mode, the signal for that mode needs to be resolved in time from other modes at all angles. This is challenging for shear (S) waves in a small model domain due to the head wave, so a technique for suppressing the head wave is shown. The multi-physics model solves for thermal expansion, which models the laser source as a surface heat flux for the Al case, and a buried heat source for the CFRP case, according to where the energy is deposited in the material. The same ultrasound generation pattern can be obtained by using a suitable pure elastodynamic loading, which is shown to be a surface force dipole as per the validation case for Al, and a buried quadrupole for the CFRP case. The modelled directivities are scaled and fitted to experimental measurements using maximum likelihood , and the goodness of fit is discussed. For the Al case, the S wave is preferred over the longitudinal (L) wave for inspection due to greater signal amplitude. For the CFRP case, the quasi-longitudinal (qL) wave in CFRP shows a maximum amplitude directly below the source, and has a greater amplitude than the quasi-shear (qS) wave, suggesting a better choice for inspection.

Influence of Initial Time of Laser Ultrasonic on Calculating Its Propagation Velocity in a Diamond Anvil Cell.

Effect of Variable Cross-Section Rod on Laser-Induced Surface Acoustic Waves.

A Study of Inner Crack Testing with the Laser Phased Array Method.

Calculation of Acoustic Field Based on Laser-Measured Vibration Velocities on Ultrasonic Transducer Surface

Numerical Simulation of the Ultrasonic Pulse Wave Propagation at Solid-Solid Interface

Off-epicentral measurement of laser-ultrasonic shear-wave velocity and its application to elastic-moduli evaluation

Simultaneous Thickness, Velocity, Density, and Attenuation Measurement of a Thin Layer by Time-Resolved Acoustic Microscopy

Investigation of the Effect of Laser Treatment on the Longitudinal and Transverse Velocity of an Aluminum Alloy

Modeling of the temperature field in nanosecond pulsed laser ablation of single crystalline diamond

Quantitative analysis of laser-generated ultrasonic wave characteristics and their correlation with grain size in polycrystalline materials

Obliquely incident ultrasonic wave propagation in a fluid-solid configuration and solid velocity measurements

Simulations Of Ultrasonic Waveform Excited By Pulsed Laser By Using Finite Element Method

Simultaneous measurement of thickness and ultrasonic wave velocity using a combination of laser-generated multiple wave modes in the thermoelastic regime

Sound velocity and absorption measurements under high pressure using picosecond ultrasonics in diamond anvil cell. Application to the stability study of AlPdMn

Finite element modelling strategy for determining directivity of thermoelastically generated laser ultrasound

Effects of pulsed laser processing on structural evolution of diamonds - A molecular dynamics and experimental study

Mechanism modelling and validation of ultrasonic vibration-assisted laser processing on metal surfaces

A Novel Approach to Correct Diffraction Effect in Measurement of Ultrasonic Velocity and Attenuation at High Frequencies

Impact of ultrasonic vibration on microstructure and mechanical properties of diamond in laser brazing with Ni–Cr filler alloy

Laser ultrasonic inspection for mechanical properties of materials at high temperature

Study on the relationship between the damage of machined surface layer and the dispersion curve of laser-induced surface acoustic wave