Abstract:Spatially resolved information on corrosion reactions operating at the cut edges of coated metals can be obtained using microelectrochemical scanning techniques using a suitable selection of operation modes and scanning probes. The scanning vibrating electrode technique (SVET) provides current density maps with a spatial resolution of the order of the dimensions of the sample, which allows the temporal evolution of the corrosion reactions to be followed over time. This leads to the identification and localization of cathodic and anodic sites, although the technique lacks chemical specificity for the unequivocal identification of the reactive species. The application of scanning electrochemical microscopy (SECM) was previously limited to image cathodic reaction sites, either due to oxygen consumption in the amperometric operation or by the alkalinisation of the electrolyte in potentiometric operation. However, it is shown that anodic sites can be effectively monitored using an ion-selective microelectrode (ISME) as a probe. The ISME probes detected differences in the local concentrations of Zn2+ and OH- ions from the cut edges of a complete coil coating system compared to the same system after the polymeric layers were removed. In this way, it has been shown that the inhibitor loading in the polymer layers effectively contributes to reducing the corrosion rates at the cut edge, thus helping to extend the useful life of the sacrificial galvanized layer bonded directly to the steel matrix. Additionally, these two probe configurations can be integrated into a multi-electrode tip for potentiometric operation to simultaneously monitor localized changes in pH values and metal ion dissolution in a single scan. Spatial and temporal distributions were further investigated using different rastering procedures, and the potential of constructing pseudomaps for 2D-imaging is described.

Dynamic Sensing of Localized Corrosion at the Metal/Solution Interface

Combining Localized Surface Plasmon Resonance with Anodic Stripping Voltammetry for Heavy Metal Ion Detection

Quasi-simultaneous electrochemical/chemical imaging of local Fe2+ and pH distributions on 316 L stainless steel surface

A New Corrosion Sensor To Determine The Start And Development Of Embedded Rebar Corrosion Process At Coastal Concrete

An Optical Fiber Sensor Method for Simultaneously Monitoring Corrosion and Structural Strain Induced by Loading

Strain-Induced Corrosion Kinetics at Nanoscale Revealed in Liquid: Enabling Control of Corrosion Dynamics of Electrocatalysis

Microscale chemical imaging to characterize and quantify corrosion processes at the metal-electrolyte interface

An Electrochemical Method for Measuring Localized Corrosion under Cathodic Protection

Novel Dual Pt-Pt/IrOx Ultramicroelectrode for Ph Imaging Using SECM in Both Potentiometric and Amperometric Modes

Mechanistic Insight into Electrode Processes by Operando Visualization of Interfacial pH Using Fluorescent Nanosensors

Experimental Investigation for Monitoring Corrosion Using Plastic Optical Fiber Sensors

In Operando Visualization and Dynamic Manipulation of Electrochemical Processes at the Electrode–Solution Interface

Contributions of Microelectrochemical Scanning Techniques for the Efficient Detection of Localized Corrosion Processes at the Cut Edges of Polymer-Coated Galvanized Steel

Visualizing and understanding corrosion evolution beneath a condensed droplet using the multi-electrode array

Deciphering the Interplay Between Local and Global Dynamics of Anodic Metal Oxidation

Smart Cathodic Protection System for Real-Time Quantitative Assessment of Corrosion of Sacrificial Anode Based on Electro-Mechanical Impedance (EMI)

In-situ radial pH monitoring inside the crevice of stainless steel combined with potentiometric scanning electrochemical microscopy

A Turn-Off Fluorescent Sensor for Metal Ions Quantifies Corrosion in an Organic Solvent

Development of an electrochemistry-based corrosion sensor to monitor corrosion of boiler tubes, pipes, and painted structures

A Fabrication of Iridium Oxide Film Ph Micro-Sensor on Pt Ultramicroelectrode and Its Application on In-Situ Ph Distribution of 316L Stainless Steel Corrosion at Open Circuit Potential