Abstract:Spatially resolved information on corrosion reactions operating at the cut edges of coated metals can be obtained using microelectrochemical scanning techniques using a suitable selection of operation modes and scanning probes. The scanning vibrating electrode technique (SVET) provides current density maps with a spatial resolution of the order of the dimensions of the sample, which allows the temporal evolution of the corrosion reactions to be followed over time. This leads to the identification and localization of cathodic and anodic sites, although the technique lacks chemical specificity for the unequivocal identification of the reactive species. The application of scanning electrochemical microscopy (SECM) was previously limited to image cathodic reaction sites, either due to oxygen consumption in the amperometric operation or by the alkalinisation of the electrolyte in potentiometric operation. However, it is shown that anodic sites can be effectively monitored using an ion-selective microelectrode (ISME) as a probe. The ISME probes detected differences in the local concentrations of Zn2+ and OH- ions from the cut edges of a complete coil coating system compared to the same system after the polymeric layers were removed. In this way, it has been shown that the inhibitor loading in the polymer layers effectively contributes to reducing the corrosion rates at the cut edge, thus helping to extend the useful life of the sacrificial galvanized layer bonded directly to the steel matrix. Additionally, these two probe configurations can be integrated into a multi-electrode tip for potentiometric operation to simultaneously monitor localized changes in pH values and metal ion dissolution in a single scan. Spatial and temporal distributions were further investigated using different rastering procedures, and the potential of constructing pseudomaps for 2D-imaging is described.

In-situ radial pH monitoring inside the crevice of stainless steel combined with potentiometric scanning electrochemical microscopy

Quasi-simultaneous electrochemical/chemical imaging of local Fe2+ and pH distributions on 316 L stainless steel surface

Novel Dual Pt-Pt/IrOx Ultramicroelectrode for Ph Imaging Using SECM in Both Potentiometric and Amperometric Modes

In Situ SECM Mapping of Pitting Corrosion in Stainless Steel Using Submicron Pt Ultramicroelectrode and Quantitative Spatial Resolution Analysis

A Fabrication of Iridium Oxide Film Ph Micro-Sensor on Pt Ultramicroelectrode and Its Application on In-Situ Ph Distribution of 316L Stainless Steel Corrosion at Open Circuit Potential

In-situ measurement of electrochemical activity related to filiform corrosion in organic coated steel by scanning vibrating electrode technique and scanning micropotentiometry

Use of Amperometric and Potentiometric Probes in Scanning Electrochemical Microscopy for the Spatially-Resolved Monitoring of Severe Localized Corrosion Sites on Aluminum Alloy 2098-T351

Direct in-situ imaging of electrochemical corrosion of Pd-Pt core-shell electrocatalysts

Selective Initiation of Corrosion Pits in Stainless Steel Using Scanning Electrochemical Cell Microscopy

Microscale chemical imaging to characterize and quantify corrosion processes at the metal-electrolyte interface

Contributions of Microelectrochemical Scanning Techniques for the Efficient Detection of Localized Corrosion Processes at the Cut Edges of Polymer-Coated Galvanized Steel

In Situ Electrochemical Monitoring of the Crevice Corrosion Process of the 7075-T651 Aluminium Alloy in Acidic NaCl and NaNO3 Solution

Perspectives on Corrosion Studies Using Scanning Electrochemical Cell Microscopy: Challenges and Opportunities

Pitting Corrosion Behavior of Stainless Steel in Ultrasonic Cell

Detecting Critical Crevice Temperature for Duplex Stainless Steels in Chloride Solutions

Combining scanning electrochemical microscopy with infrared attenuated total reflection spectroscopy for in situ studies of electrochemically induced processes

Online Corrosion Monitoring of Photoelectrochemical Cathodic Protection of Carbon Steel Using Particle Video Microscope

Crevice Corrosion Behavior of 201 Stainless Steel in NaCl Solutions with Different pH Values by In Situ Monitoring

In Situ Study of Corrosion with an Atomic Force Microscope Scanning in Liquids

Practical Aspects of Electrochemical Corrosion Measurements During In Situ Analytical Transmission Electron Microscopy (TEM) of Austenitic Stainless Steel in Aqueous Media

Time-Lapse Observation of Crevice Corrosion in Grade 2205 Duplex Stainless Steel