Hierarchical Micro/Nano Porous Silicon Li-Ion Battery Anodes

Yu Zhao,Xizheng Liu,Huiqiao Li,Tianyou Zhai,Haoshen Zhou

DOI: https://doi.org/10.1039/c2cc31476b

IF: 4.9

2012-01-01

Chemical Communications

Abstract:A wet-chemical etching method is reported for the scale-up preparation of carbon-coated hierarchical micro/nano porous silicon powders as a Li-ion battery anode, which shows no capacity fading at 1500 mA h g(-1) in 50 charge/discharge cycles.

What problem does this paper attempt to address?

Scalable and Low-Cost Synthesis of Porous Silicon Nanoparticles As High-Performance Lithium-Ion Battery Anode

Z. Yan,J. Jiang,Y. Zhang,D. Yang,N. Du

DOI: https://doi.org/10.1016/j.mtnano.2022.100175

IF: 10.3

2022-01-01

Materials Today Nano

Abstract:We design porous silicon (Si) nanoparticles with both nanosize and porous structures via a simple alkaline etching method. The etching at grain boundaries and the anisotropic etching of the different crystal planes of the polycrystalline silicon are responsible for the homogeneous porous nanostructures. After the porous Si nanoparticles are coated with carbon layer, the composite delivering a discharge capacity of 1645.6 mAh g(-1) at 0.4 A g(-1) after 200 cycles, an outstanding discharge capacity of 861.5 mA g(-1) at 4 A g(-1) after 800 cycles with a high capacity retention of more than 65%, and a rate capacity of 904.7 mA g(-1) at 12.8 A g(-1). The porous nanoparticles show both the nanosize (similar to 100 nm) and the porous structure, which can furthest accommodate the large volume changes of the Si anode, resulting in the good electrochemical performance. The design of porous Si nanoparticles with a high yield of 93% may give a scalable, low-cost, and green approach for commercial silicon-based anodes of lithium-ion batteries. (C) 2022 Published by Elsevier Ltd.
Scalable Preparation of Porous Silicon Nanoparticles and Their Application for Lithium-Ion Battery Anodes

Mingyuan Ge,Jiepeng Rong,Xin Fang,Anyi Zhang,Yunhao Lu,Chongwu Zhou

DOI: https://doi.org/10.1007/s12274-013-0293-y

2013-01-01

Abstract:Nanostructured silicon has generated significant excitement for use as the anode material for lithium-ion batteries; however, more effort is needed to produce nanostructured silicon in a scalable fashion and with good performance. Here, we present a direct preparation of porous silicon nanoparticles as a new kind of nanostructured silicon using a novel two-step approach combining controlled boron doping and facile electroless etching. The porous silicon nanoparticles have been successfully used as high performance lithium-ion battery anodes, with capacities around 1,400 mA·h/g achieved at a current rate of 1 A/g, and 1,000 mA·h/g achieved at 2 A/g, and stable operation when combined with reduced graphene oxide and tested over up to 200 cycles. We attribute the overall good performance to the combination of porous silicon that can accommodate large volume change during cycling and provide large surface area accessible to electrolyte, and reduced graphene oxide that can serve as an elastic and electrically conductive matrix for the porous silicon nanoparticles.
Hierarchical porous silicon structures with extraordinary mechanical strength as high-performance lithium-ion battery anodes

Haiping Jia,Xiaolin Li,Junhua Song,Xin Zhang,Langli Luo,Yang He,Binsong Li,Yun Cai,Shenyang Hu,Xingcheng Xiao,Chongmin Wang,Kevin M. Rosso,Ran Yi,Rajankumar Patel,Ji-Guang Zhang

DOI: https://doi.org/10.1038/s41467-020-15217-9

IF: 16.6

2020-03-19

Nature Communications

Abstract:Abstract Porous structured silicon has been regarded as a promising candidate to overcome pulverization of silicon-based anodes. However, poor mechanical strength of these porous particles has limited their volumetric energy density towards practical applications. Here we design and synthesize hierarchical carbon-nanotube@silicon@carbon microspheres with both high porosity and extraordinary mechanical strength (>200 MPa) and a low apparent particle expansion of ~40% upon full lithiation. The composite electrodes of carbon-nanotube@silicon@carbon-graphite with a practical loading (3 mAh cm −2 ) deliver ~750 mAh g −1 specific capacity, <20% initial swelling at 100% state-of-charge, and ~92% capacity retention over 500 cycles. Calendered electrodes achieve ~980 mAh cm −3 volumetric capacity density and <50% end-of-life swell after 120 cycles. Full cells with LiNi 1/3 Mn 1/3 Co 1/3 O 2 cathodes demonstrate >92% capacity retention over 500 cycles. This work is a leap in silicon anode development and provides insights into the design of electrode materials for other batteries.

multidisciplinary sciences
Hierarchical Carbon Shell Compositing Microscale Silicon Skeleton As High-Performance Anodes for Lithium-Ion Batteries

Weili An,Peng He,Chengmao Xiao,Eming Guo,Chunlei Pang,Xueqin He,Jianguo Ren,Guohui Yuan,Ning Du,Deren Yang

DOI: https://doi.org/10.1021/acsaem.1c00529

IF: 6.4

2021-01-01

ACS Applied Energy Materials

Abstract:Si is a promising high-capacity anode material; however, its practical implementation is hindered by its huge volume expansion, low initial Coulombic efficiency (ICE), poor cycling life, and high cost. To address these issues, a novel microscale Si skeleton (MSS) material is synthesized, and a dual carbon-hybridized MSS hierarchical architecture composite (MSS@CC@CS) is fabricated by a conformal carbon first coating and nonfilling carbon shell secondary encapsulation. The MSS consisting of interconnected Si nanoskeletons and continuous interpenetrating pores avoids pulverization and accommodates volume expansion, resulting in low electrode swelling. The conformal carbon coating enhances the internal conductivity and structural stability of MSS, and the carbon shell encapsulation further strengthens the structural integrity and greatly improves the ICE of the Si anode. As an anode, MSS@CC@CS shows a high ICE of 90.5%, a high half-cell capacity of 1353.8 mA h g(-1) at 0.5 C with 89.8% capacity retention after 800 cycles, and a low electrode swelling of 12.4%. Paired with a commercial NCA cathode after blending graphite to assemble a 3.5 A h cylindrical cell, an energy density of 286.4 W h kg(-1) and superior cycle performance with 82.7% capacity retention after 1200 cycles are achieved, showing a great application potential in powering large devices.
Large-scale Fabrication, 3D Tomography, and Lithium-Ion Battery Application of Porous Silicon.

Mingyuan Ge,Yunhao Lu,Peter Ercius,Jiepeng Rong,Xin Fang,Matthew Mecklenburg,Chongwu Zhou

DOI: https://doi.org/10.1021/nl403923s

IF: 10.8

2013-01-01

Nano Letters

Abstract:Recently, silicon-based lithium-ion battery anodes have shown encouraging results, as they can offer high capacities and long cyclic lifetimes. The applications of this technology are largely impeded by the complicated and expensive approaches in producing Si with desired nanostructures. We report a cost-efficient method to produce nanoporous Si particles from metallurgical Si through ball-milling and inexpensive stain-etching. The porosity of porous Si is derived from particle's three-dimensional reconstructions by scanning transmission electron microscopy (STEM) tomography, which shows the particles' highly porous structure when etched under proper conditions. Nanoporous Si anodes with a reversible capacity of 2900 mAh/g was attained at a charging rate of 400 mA/g, and a stable capacity above 1100 mAh/g was retained for extended 600 cycles tested at 2000 mA/g. The synthetic route is low-cost and scalable for mass production, promising Si as a potential anode material for the next-generation lithium-ion batteries with enhanced capacity and energy density.
Pomegranate-like silicon-based anodes self-assembled by hollow-structured Si/void@C nanoparticles for Li-ion batteries with high performances

Dajin Chen,Chuanying Tao,Tongzhou Chen,Xiaohan Liu,Yong Liu,Gang Xu,Gaorong Han

DOI: https://doi.org/10.1088/1361-6528/abc84e

IF: 3.5

2021-01-01

Nanotechnology

Abstract:Silicon is considered as one of the most promising alternatives to the graphite anode for lithium-ion batteries due to its high theoretical capacity (4200 mAh g(-1)). However, its fragile solid electrolyte interphase cannot tolerate the large volume changes of bare silicon induced by the lithium insertion and extraction, resulting in low Coulombic efficiency. In previous reports, a yolk-shell design, such as Si@void@C, in which the well-defined space allows the silicon particles to expand freely without breaking the outer carbon shells, can effectively improve the Columbic efficiency. Here, we design a pomegranate-like silicon-based anodes self-assembled by the hollow-structured Si/void@C nanoparticles, in which silicon and some voids are together sealed in the outer carbon shells, by the magnesiothermic reduction of the colloidal SiO2@PEI nanospheres prepared by the hydrolysis of the tetraethoxysilane under the catalytic effect of polyetherimide (PEI). Due to the tolerance of the presealed void in the carbon shells of the primary hollow-structured Si/void@C nanoparticles, the prepared pomegranate-like silicon-based anodes deliver a high reversible capacity of 1615 mAh g(-1) at 0.1 C and long cycle life of 73.5% capacity retention at 2 C after 500 cycles, as well as high Coulombic efficiency of 99%.
Structure and Conductivity Enhanced Treble-Shelled Porous Silicon As an Anode for High-Performance Lithium-Ion Batteries

Yangfan Lin,Hanging Lin,Jingwei Jiang,Deren Yang,Ning Du,Xueqin He,Jianguo Ren,Peng He,Chunlei Pang,Chengmao Xiao

DOI: https://doi.org/10.1039/c9ra06576h

IF: 4.036

2019-01-01

RSC Advances

Abstract:Silicon is regarded as the next generation anode material for lithium-ion batteries because of its high specific capacity, low intercalation potential and abundant reserves. However, huge volume changes during the lithiation and delithiation processes and low electrical conductivity obstruct the practical applications of silicon anodes. In this study, a treble-shelled porous silicon (TS-P-Si) structure was synthesized via a three-step approach. The TS-P-Si anode delivered a capacity of 858.94 mA h g(-1) and a capacity retention of 87.8% (753.99 mA h g(-1)) after being subjected to 400 cycles at a current density of 400 mA g(-1). The good cycling performance was due to the unique structure of the inner silicon oxide layer, middle silver nano-particle layer and outer carbon layer, leading to a good conductivity and a decreased volume change of this silicon-based anode.
Hierarchical conformal coating enables highly stable microparticle Si anodes for advanced Li-ion batteries

Yaxiong Yang,Shugang Liu,Zhe Dong,Zhenguo Huang,Cheng Lu,Yongjun Wu,Mingxia Gao,Yongfeng Liu,Hongge Pan

DOI: https://doi.org/10.1016/j.apmt.2022.101403

IF: 8.663

2022-03-01

Applied Materials Today

Abstract:Microsized silicon powders have great potential for high capacity anode materials in next-generation lithium ion batteries, because of the high gravimetric and volumetric energy densities, ease of mass production and low costs. However, large volume change and consequently rapid capacity fading upon lithiation and delithiation prevent its practical applications. Herein, we demonstrate an effective hierarchical conformal coating strategy for high-performance microsized Si anodes. The Si-based composites consist of an amorphous Li-Si-O inner coating layer and a graphene outer encapsulation layer, which are prepared by coupling reactive milling with electrostatic self-assembly. This unique hierarchical conformal coating structure not only strengthens the mechanical property (31.8 GPa for the elastic modulus) and promotes the ionic diffusion (2.03 × 10−10 cm2 s−1) of Si anode, but also effectively stabilizes the electrode/electrolyte interfaces and increases the electronic conductivity. As a result, a high reversible capacity (1450 mA⋅h g−1 at 0.1 A g−1), good cycling stability (97.7% of capacity retention from the 2nd to the 310th cycle at 0.5 A g−1), and high rate capability (703 mA⋅h g−1 at 5 A g−1) have been successfully achieved. These findings provide new insights into the improvement of electrochemical properties of microsized Si composite anodes for high-performance Li-ion batteries.

materials science, multidisciplinary
Rational Design of Three-Dimensional Macroporous Silicon As High Performance Li-ion Battery Anodes with Long Cycle Life

Hao Wu,Ning Du,Xianxing Shi,Deren Yang

DOI: https://doi.org/10.1016/j.jpowsour.2016.09.046

IF: 9.2

2016-01-01

Journal of Power Sources

Abstract:Three-dimensional (3D) macroporous silicon with stable interconnected structure is prepared by magnesiothermic reduction based on deliberate design, while flexible morphological control of zero dimensional (OD) hollow nanospheres is realized via simply altering the conditions of the same reaction. When used as anode materials in lithium-ion batteries, the empty space in both structures allows for effective accommodation of large volume changes during lithium insertion and extraction. Due to the robustness of the interconnected porous structure, the 3D Si@C electrode exhibits better electrochemical properties with a reversible capacity of 1058 mAh g(-1) after 800 cycles and 91% capacity retention (only 0.012% capacity degradation per cycle). The coulombic efficiency of the 3D porous electrode stabilizes at 99.4% in later cycles. The results demonstrated herein provide a better understanding of the controllable magnesiothermic reduction reaction, which is potentially an efficient method for large scale synthesis of high-performance Si anodes. (C) 2016 Elsevier B.V. All rights reserved.
Diatomite‐Derived Hierarchical Porous Crystalline‐AmorphousNetwork for High‐Performance and Sustainable Si Anodes

Ying Zhang,Rui Zhang,Shucheng Chen,Hongpeng Gao,Mingqian Li,Xiaolan Song,Huolin L. Xin,Zheng Chen

DOI: https://doi.org/10.1002/adfm.202005956

IF: 19

2020-09-13

Advanced Functional Materials

Abstract:Silicon has attracted considerable interest as a high‐capacity anode material for next‐generation lithium‐ion batteries. However, Si‐based anodes suffer extreme volume change (≈380%) upon lithiation and delithiation, which results in rapid capacity fading due to mechanical and electrochemical failure during cycling. Herein, a sustainable and scalable method to synthesize hierarchically porous micron‐sized Si particles from the low‐cost diatomite precursor is reported, which serves as both the precursor and the template. Through a one‐step magnesiothermic reduction, the SiO2 constituent in diatomite is reduced to form a Si/SiO2 composite network with 10–30 nm crystalline Si domains embedded within an amorphous SiO2 matrix. Controlling the reduction time leads to an optimal ratio between the crystalline Si and the amorphous SiO2 constituent, which endows the composite structure with high capacity and excellent cycling stability. For example, 90% capacity can be retained after 500 cycles at 0.2C for sample reduced by 6 h without any coating or prelithiation. The full cell with such Si/SiO2 as the anode and LiNi0.8Co0.1Mn0.1O2 as the cathode shows ≈80% capacity retention after 200 cycles. This work creates a unique path towards sustainable and scalable production of high‐performance micron‐sized Si anodes, offering new opportunities for potential industrial applications.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Scalable synthesis of micrometer-sized porous silicon/carbon composites for high-stability lithium-ion battery anodes

Haiping Su,Xinrui Li,Changwei Liu,Yazhuo Shang,Honglai Liu

DOI: https://doi.org/10.1016/j.cej.2022.138394

IF: 15.1

2022-08-13

Chemical Engineering Journal

Abstract:Although silicon is considered as one of the most promising anode materials, challenges related to the huge volume expansion, low conductivity, as well as tedious synthesis process hinder the practical applications. Herein, a micrometer-sized porous silicon/carbon composite () is synthesized via a spray drying process and magnesiothermic reduction method. The spherical composite exhibits high porosity with rich interconnected channels under the protecting carbon shell, which can not only alleviate the volume expansion but also improve the electrode conductivity. The electrode has demonstrated excellent electrochemical stability and rate performance, delivering a reversible capacity of 1702 mAh g −1 after 250 cycles at 1 A/g, and a high capacity of 1002 mAh g −1 after 500 cycles at 2 A/g with a capacity retention of 95%. This scalable preparation of micrometer-sized Si/C anode offers great potentials for next-generation lithium ion batteries.

engineering, chemical, environmental
Porous Carbon-Coated Silicon Composites for High Performance Lithium-Ion Batterie Anode

Duo Wang,Lingyu Kong,Fang Zhang,Aimin Liu,Haitao Huang,Yubao Liu,Zhongning Shi

DOI: https://doi.org/10.1016/j.apsusc.2024.160076

IF: 6.7

2024-01-01

Applied Surface Science

Abstract:With the rapid development of silicon-based lithium-ion battery anode, the commercialization process highlights the importance of low-cost and short-flow production processes. The porous carbon/silicon composites (C/Si) are prepared by one-step calcination using zinc citrate and nano-silicon as the primary raw materials at a temperature of 950 degrees C. In this composite, silicon nanoparticles are coated with a porous carbon shell with an average pore diameter of 4.49 nm, which improves the structural stability and electrochemical performance of the anode. Density-functional theory calculations show that the porous carbon enhances the electrical conductivity, facilitates the interlayer migration of Li-ion, and strengthens the gain effect of stress on conductivity. Additionally, stress further reduces the diffusion barriers of Li-ion. The porous C/Si anode demonstrates outstanding specific capacity and rate capability, maintaining a stable specific capacity of 1170 mAh/g at a current density of 0.2 A g-1 after 100 cycles and retaining a reversible specific capacity of 944 mAh/g even at a charging current density of 2 A g-1. The carbon/silicon anode materials prepared using this strategy present a streamlined manufacturing process and exceptional performance, as well as avoiding the post-washing step, providing a pathway toward the scalable application of silicon-based anodes.
Micro-sized nano-porous Si/C anodes for lithium ion batteries

huajun tian,xiaojian tan,fengxia xin,chunsheng wang,weiqiang han

DOI: https://doi.org/10.1016/j.nanoen.2014.11.031

IF: 17.6

2015-01-01

Nano Energy

Abstract:The unique micro-sized (2–10µm) Si/C composites consisting of 20nm carbon coated secondary Si were synthesized from the abundant and low cost Al–Si alloy ingot by acid etching, ball-milling and carbonization procedure. The nano-porous Si/C composites provide a capacity of 1182mAhg−1 at a current density of 50mAg−1, 952mAhg−1 at 200mAg−1, 815mAhg−1 at 500mAg−1, and maintain 86.8% of initial capacity after 300 cycles. Even at a much higher current density of 10A/g, the porous Si/C anode can still provide capacities of >200mAhg−1. Its superior rate capability and cycling stability of micro-sized nano-porous Si/C anodes is because it takes advantage of both long cycle life of nano-Si and high volumetric/gravimetric capacity of micro-Si. The hierarchical porous micro-scale Si/C with the carbon coating can stabilize the SEI layer and the inside pore provides adequate space for Si expansion, relaxing the stress/strain. The hierarchical Si/C with exceptional electrochemical performance is prepared by a simple, low-cost and saleable synthesis method, making it very promising for a large-scale production of high-performance Si-based anode materials in high-energy lithium-ion batteries.
Rational-design micro-nanostructure of porous carbon film/silicon nanowire/graphite microsphere composites for high-performance lithium-ion batteries

Bei Liu,Peng Huang,Qi Zhang,Qizhong Huang,Zhiyong Xie

DOI: https://doi.org/10.1007/s10853-020-04869-z

IF: 4.5

2020-06-02

Journal of Materials Science

Abstract:Silicon-based anodes are promising anode materials for lithium-ion batteries. However, during the charge–discharge processes, the huge volume change of silicon leads to the repeated formation of solid-electrolyte interphase layer, structure fracture and loss of electric contact, which seriously limits their practical applications. In this paper, a rational design combining graphite microsphere, silicon nanowire and porous carbon film is established, forming a micro-nanostructure that can effectively solve the above issues. Employing chemical vapor deposition method, silicon nanowire and polypyrrole are successively in situ synthesized on the graphite surface. After carbonizing the deposited composites, a porous carbon film and a silicon carbide layer locating between silicon and carbon film are obtained. It establishes a novel microstructure that possesses a strong bonding strength among interfaces of carbon film/silicon and silicon/graphite. Therefore, the porous carbon film/silicon nanowire/graphite microsphere composites anode exhibits a high capacity of 530 mA h g−1 at a current density of 0.2 C after 100 cycles. Significantly, the prepared composites anode could satisfy the practical application because their initial coulomb efficiency can reach to 80%.Graphic abstract

materials science, multidisciplinary
Scalable synthesis of ant-nest-like bulk porous silicon for high-performance lithium-ion battery anodes

Weili An,Biao Gao,Shixiong Mei,Ben Xiang,Jijiang Fu,Lei Wang,Qiaobao Zhang,Paul K. Chu,Kaifu Huo

DOI: https://doi.org/10.1038/s41467-019-09510-5

IF: 16.6

2019-03-29

Nature Communications

Abstract:Although silicon is a promising anode material for lithium-ion batteries, scalable synthesis of silicon anodes with good cyclability and low electrode swelling remains a significant challenge. Herein, we report a scalable top-down technique to produce ant-nest-like porous silicon from magnesium-silicon alloy. The ant-nest-like porous silicon comprising three-dimensional interconnected silicon nanoligaments and bicontinuous nanopores can prevent pulverization and accommodate volume expansion during cycling resulting in negligible particle-level outward expansion. The carbon-coated porous silicon anode delivers a high capacity of 1,271 mAh g−1 at 2,100 mA g−1 with 90% capacity retention after 1,000 cycles and has a low electrode swelling of 17.8% at a high areal capacity of 5.1 mAh cm−2. The full cell with the prelithiated silicon anode and Li(Ni1/3Co1/3Mn1/3)O2 cathode boasts a high energy density of 502 Wh Kg−1 and 84% capacity retention after 400 cycles. This work provides insights into the rational design of alloy anodes for high-energy batteries.

multidisciplinary sciences
Carbon-coated mesoporous silicon shell-encapsulated silicon nano-grains for high performance lithium-ion batteries anode

Jie Wang,Chunhui Gao,Zhao Yang,Min Zhang,Zhaolin Li,Hailei Zhao

DOI: https://doi.org/10.1016/j.carbon.2022.02.063

IF: 10.9

2022-06-01

Carbon

Abstract:Silicon is considered to be a promising anode material because of its higher theoretical specific capacity. However, the huge volume change in cycles leads to a severe pulverization of active silicon and thus rapid capacity fade. Herein, to address this issue, we report a novel hollow-structured Si/C (H–SiNS/C) nanocomposite fabricated via a simple, facile approach. In the composite, lots of tiny Si nano-grains are encapsulated by a thin mesoporous Si shell, which is further coated by a carbon layer. The mesoporous Si shell with abundant internal voids can effectively accommodate the volume changes and relieve the mechanical stress during repeated (de)lithiation processes. Besides, the carbon layer can function as the hard physical-mechanical support to further confine the internal Si shell expansion/contraction, guaranteeing the whole particle structural integrity. Moreover, the conductive framework constructed by the carbon layer favors the electrode reaction kinetics as well as the uniform volume variation of Si. As a result, the H–SiNS/C nanocomposite displays a high reversible capacity (0.1 A g−1: ∼1670 mAh g−1), an excellent rate capability (2 A g−1: >1150 mAh g−1) with a high average Coulombic efficiency (∼99.8%), and a superior cycling stability.

materials science, multidisciplinary,chemistry, physical
Facile preparation of silicon/carbon composite with porous architecture for advanced lithium-ion battery anode

Haofeng Shi,Wenyuan Zhang,Donghua Wang,Jiashuai Wang,Chengdeng Wang,Zhihao Xiong,Fu-Rong Chen,Hailiang Dong,Bingshe Xu,Xiaoqin Yan

DOI: https://doi.org/10.1016/j.jelechem.2023.117427

IF: 4.598

2023-04-10

Journal of Electroanalytical Chemistry

Abstract:Silicon is a potential anode material for Li battery due to its high theoretical specific capacity (4200 mAh g −1 ). However, Si is hampered for practical application in Li-battery due to its enormous volume alternation causing instability. Herein, we demonstrated a novel carbon-coated porous structure (/Si-G) synthesized by uniformly wrapping Si into pitch pyrolytic carbon shells and then in-situ removing the sodium chloride template can overcome the bottleneck. It is worth noting that our process for /Si-G also offers a simple route for cost down and mass production of anode material. The /Si-G anodes exhibit an excellent capacity of 1082.7 mAh g −1 at 0.2 C after 200 cycles. Furthermore, it holds a high capacity retention of 81.9 % after 500 cycles at 0.5 C. We found that /Si-G composite only rises about 41% volumetric expansion during 500 operation cycles. This can effectively avoid direct contact between silicon and electrolyte to form a stable solid electrolyte interphase (SEI) film. Especially, practical application of the /Si-G anode is demonstrated in a full cell pairing with LiNi 0.3 Co 0.3 Mn 0.3 O 2 cathode. The full cell presents great cycle retention of 90.1 % at 0.2 C after 100 cycles and a high energy density (446 Wh kg −1 ).

chemistry, analytical,electrochemistry
Scalable Synthesis of Porous Silicon by Acid Etching of Atomized Al-Si Alloy Powder for Lithium-Ion Batteries

Hiroyuki Kawaura,Ryo Suzuki,Yasuhito Kondo,Yuji Mahara

DOI: https://doi.org/10.1021/acsami.3c05521

2023-07-26

Abstract:Si anodes have attracted considerable attention for their potential application in next-generation lithium-ion batteries because of their high specific capacity (Li15Si4, 3579 mAh g-1) and elemental abundance. However, Si anodes have not yet been practically applied in lithium-ion batteries because the volume change associated with lithiation and delithiation degrades their capacity during cycling. Instead of considering the active material, we focused on the structural design and developed a scalable process for producing Si anodes with excellent cycle characteristics while precisely controlling the morphology. Al-Si alloy powders were prepared by gas atomization, and porous Si with a skeletal structure was prepared by leaching Al using HCl. Porous Si (p-Si12, p-Si19) prepared from Al88Si12 and Al81Si19 comprised resinous eutectic Si, and porous Si (p-Si25) prepared from Al75Si25 comprised lumpy primary Si and resinous eutectic Si. The porosity of the Si anodes varied from 63% to 76%, depending on the Si composition. The p-Si19 anode displayed the finest pore distribution (20-200 nm), excellent rate characteristics, a reversible discharge capacity of 1607 mAh g-1 after 200 cycles at a rate of 0.1 C with a Coulombic efficiency of over 97%, and high stability. The performances of the p-Si25 and p-Si19 electrodes began to decrease after 250 and 850 cycles, respectively, with a constant-charge capacity of 1000 mAh g-1 and at a rate of 0.2 C. In contrast, the p-Si12 anode maintained its discharge capacity at 1000 mAh g-1 for up to 1000 cycles without degradation. Therefore, the developed manufacturing process is expected to produce porous Si as an active material in lithium-ion batteries for high capacity and long life at an industrial scale.
Nano-Si/C microsphere with hollow double spherical interlayer and submicron porous structure to enhance performance for lithium-ion battery anode

Hedong Chen,Shenggong He,Xianhua Hou,Shaofeng Wang,Fuming Chen,Haiqing Qin,Yingchun Xia,Guofu Zhou

DOI: https://doi.org/10.1016/j.electacta.2019.04.170

IF: 6.6

2019-07-01

Electrochimica Acta

Abstract:Silicon (Si) applied for lithium-ion battery anode is of immense prospect due to high theoretical capacity, non-toxic, abundant reserves and low-cost. But the electrode materials, maintaining stable structure during repeated discharge/charge processes, need to be explored, which can realize the long-life. To address this problem, we utilized hollow porous pollen carbon microsphere derived from biomass as hard template to accommodate nano-Si. The hollow porous carbon@nano-Si@graphene sheets (HPC@nano-Si@GS) microspheres with hollow double spherical interlayer and submicron porous structure have been successfully synthesized via a simple and green environment-protecting wet-chemical method. We decorate nano-Si with silane coupling agent which can bind hollow porous pollen and graphene oxide, realizing the strong fixation and protection of nano-Si. Furthermore, the surface submicron mesh pores and HPC microsphere provide enough buffer space to cushion the huge volume expansion for nano-Si, enhancing the cyclic stability. Finally, graphene wrapping on the surface of HPC@nano-Si@GS microspheres can protect nano-Si very well, further stabilizing the composite structure. Nano-Si particles were accommodated in the HPC microsphere with submicron pores and then coated by wrinkled graphene sheets, to form the strong structure with hollow double spherical interlayer. A series of electrochemical tests indicate that prepared HPC@nano-Si@GS microspheres with hollow porous carbon structure exhibit outstanding electrochemical properties.

electrochemistry
Multi-step low-cost synthesis of ultrafine silicon porous structures for high-reversible lithium-ion battery anodes

Yifan Chen,Yongjun Yuan,Cong Xu,Liang Bao,Tao Yang,Ning Du,Yangfan Lin,Huaiwei Zhang

DOI: https://doi.org/10.1007/s10853-020-05021-7

IF: 4.5

2020-07-06

Journal of Materials Science

Abstract:We demonstrate multi-step synthesis of silicon porous structures with various particle sizes via low-cost annealing and pickling reactions from ball-milled Mg2Si or Si/Mg powder. Thereinto, the ultrafine Si porous structures (< 50 nm) have been prepared by the two-step alloying/de-alloying processes between Si and Mg, and the formation processes and reaction mechanism have been discussed as well. When used as an anode material for lithium-ion batteries, the porous Si anode with finer particle size shows better capacity retention and coulombic efficiency, confirming the particle size has a great impact on cycling performance. Moreover, the ultrafine porous Si anodes without any buffer medium demonstrate a reversible discharge capacity of ~ 800 mAhg−1 after 1000 long cycles at 1 Ag−1, which is extremely better than the commercial nano-Si particles and graphite anodes. It is believed that the good electrochemical performance could be attributed to the uniform porous structure and superfine particle size that can alleviate the volume change significantly. Hence, these low-cost and simple scalable methods have provided useful strategies for the industrialization of Si anode materials.

materials science, multidisciplinary

Hierarchical Micro/Nano Porous Silicon Li-Ion Battery Anodes

Scalable and Low-Cost Synthesis of Porous Silicon Nanoparticles As High-Performance Lithium-Ion Battery Anode

Scalable Preparation of Porous Silicon Nanoparticles and Their Application for Lithium-Ion Battery Anodes

Hierarchical porous silicon structures with extraordinary mechanical strength as high-performance lithium-ion battery anodes

Hierarchical Carbon Shell Compositing Microscale Silicon Skeleton As High-Performance Anodes for Lithium-Ion Batteries

Large-scale Fabrication, 3D Tomography, and Lithium-Ion Battery Application of Porous Silicon.

Pomegranate-like silicon-based anodes self-assembled by hollow-structured Si/void@C nanoparticles for Li-ion batteries with high performances

Structure and Conductivity Enhanced Treble-Shelled Porous Silicon As an Anode for High-Performance Lithium-Ion Batteries

Hierarchical conformal coating enables highly stable microparticle Si anodes for advanced Li-ion batteries

Rational Design of Three-Dimensional Macroporous Silicon As High Performance Li-ion Battery Anodes with Long Cycle Life

Diatomite‐Derived Hierarchical Porous Crystalline‐AmorphousNetwork for High‐Performance and Sustainable Si Anodes

Scalable synthesis of micrometer-sized porous silicon/carbon composites for high-stability lithium-ion battery anodes

Porous Carbon-Coated Silicon Composites for High Performance Lithium-Ion Batterie Anode

Micro-sized nano-porous Si/C anodes for lithium ion batteries

Rational-design micro-nanostructure of porous carbon film/silicon nanowire/graphite microsphere composites for high-performance lithium-ion batteries

Scalable synthesis of ant-nest-like bulk porous silicon for high-performance lithium-ion battery anodes

Carbon-coated mesoporous silicon shell-encapsulated silicon nano-grains for high performance lithium-ion batteries anode

Facile preparation of silicon/carbon composite with porous architecture for advanced lithium-ion battery anode

Scalable Synthesis of Porous Silicon by Acid Etching of Atomized Al-Si Alloy Powder for Lithium-Ion Batteries

Nano-Si/C microsphere with hollow double spherical interlayer and submicron porous structure to enhance performance for lithium-ion battery anode

Multi-step low-cost synthesis of ultrafine silicon porous structures for high-reversible lithium-ion battery anodes