Abstract:Although the socket is critical in a prosthetic system for a person with limb amputation, the methods of its design are largely artisanal. A roadblock for a repeatable and quantitative socket design process is the lack of predictive and patient specific biomechanical models of the residuum. This study presents the evaluation of such a model using a combined experimental-numerical approach. The model geometry and tissue boundaries are derived from MRI. The soft tissue non-linear elastic and viscoelastic mechanical behavior was evaluated using inverse finite element analysis (FEA) of in-vivo indentation experiments. A custom designed robotic in-vivo indentation system was used to provide a rich experimental data set of force versus time at 18 sites across a limb. During FEA, the tissues were represented by two layers, namely the skin-adipose layer and an underlying muscle-soft tissue complex. The non-linear elastic behavior was modeled using 2nd order Ogden hyperelastic formulations, and viscoelasticity was modeled using the quasi-linear theory of viscoelasticity. To determine the material parameters for each tissue, an inverse FEA based optimization routine was used that minimizes the combined mean of the squared force differences between the numerical and experimental force-time curves for indentations at 4 distinct anatomical regions on the residuum. The optimization provided the following material parameters for the skin-adipose layer: c=5.22 kPa, m=4.79, gamma=3.57 MPa, tau=0.32 s and for the muscle-soft tissue complex: c=5.20 kPa, m=4.78, gamma=3.47 MPa, tau=0.34 s. These parameters were evaluated to predict the force-time curves for the remaining 14 anatomical locations. The mean percentage error (mean absolute error/ maximum experimental force) for these predictions was 7 +/- 3%. The mean percentage error at the 4 sites used for the optimization was 4%.

[Three-Dimensional Finite Element Analyses on the Transtibial Residual Limb and Its Prosthetic Socket].

Finite Element Modeling of the Contact Interface Between Trans-Tibial Residual Limb and Prosthetic Socket.

Three dimensional finite dynamic analysis of the residual limb and prosthetic socket

[The 3D Finite Element Stress Analysis of Transtibial Monolimb].

3D Finite Element Dynamic Analysis of Interface Stress at Residual Limb of a Trans-Tibial Amputee

3D Modeling and Biomechanical Analysis to Residual Limb and Prosthetic Socket

Finite element modelling of a residual lower-limb in a prosthetic socket: a survey of the development in the first decade

A Quasi-Dynamic Nonlinear Finite Element Model to Investigate Prosthetic Interface Stresses During Walking for Trans-Tibial Amputees

[Inertial Effects on Interface Pressure Between Prosthetic Socket and Residual Limb].

Load transfer mechanics between trans-tibial prosthetic socket and residual limb--dynamic effects.

Dynamic Investigation of Interface Stress on Below-Knee Residual Limb in a Prosthetic Socket

[Valid Constructing Method of Three-Dimensional Finite Element Human Foot Model and Experimental Analysis on Its Rationality].

The Investigation on a Quasi-Dynamic Finite Element Model to Predict Interface Pressure on Below-Knee Residual Limb

Effect of Dynamic Loads on the Interface Pressure at the Residual Limb of a Trans-Tibial Amputee

Stress analysis of osseointegrated transfemoral prosthesis: a finite element model.

Comparison of mechanical conditions in a lower leg model with 5 or 6 tissue types while exposed to prosthetic sockets applying finite element analysis

Three-dimensional Finite-Element Analysis and Biomechanical Design of Femoral Prosthesis

Comparative biomechanical analysis of a conventional/novel hip prosthetic socket

Multi-Material 3-D Viscoelastic Model of a Transtibial Residuum from In-vivo Indentation and MRI Data

ESTABLISHMENT AND APPLICATION OF LOWER LIMB FINITE ELEMENT MODEL BASED ON MUSCLE GROUPS

Three-dimensional finite element analysis of hip joint replacement