[Temperature Measuring and Heating Controlling in Transurethral Prostate Thermotherapy System].

L Luo,Q Wang,Y Chen,X Yu

1997-01-01

Abstract:This paper introduces the system construction of Transurethral Prostate Thermotherapy Device. The temperature measuring device, I/O interface circuit and the programming principle of PID controlling system is illustrated also.

What problem does this paper attempt to address?

Development of A Temperature Control System for Isolated Kidney Preservation Device Based on the Semiconductor Temperature Control Technology

Zhi-liang DING,Liang HU,Guo-ping TANG

DOI: https://doi.org/10.3969/j.issn.1674-1633.2015.02.008

2015-01-01

Abstract:Renal transplantation is one of the main treatments for the end-stage nephrotic syndrome. In order to improve the success rate of transplantation, the donor kidney should be preserved in low temperature before transplantation. In this paper, an easy-to-use temperature control system with high precision and rapid response speed for isolated kidney preservation device was presented. The semiconductor temperature control technology was applied in this system to control the temperature of isolated kidneys. The platinum resistance (Pt100) was used as temperature sensor and the PID (proportional-integral-derivative) controller was taken as the temperature control policies. According to the experimental results, the temperature overshoot of the system was less than 0.3 ℃ and the temperature accuracy was ±0.2℃when it worked at the temperature of 23℃±2℃, which satisifed the temperature requirements of preservation of isolated kidneys.
Design of Temperature Testing System in Multi-Parameter Combined Environmental Test

Guanhua Xu,Wen He,Runjie Shen

DOI: https://doi.org/10.4028/www.scientific.net/amm.157-158.127

2012-01-01

Applied Mechanics and Materials

Abstract:A novel design of a temperature test chamber in multi-parameter combined environmental test was introduced, in which thermoelectric coolers were adopted to achieve both high and low temperature. Multiple distributed actuators and temperature sensors were used for improving the evenness of the temperature field. A well performed cooling system for waste heat dissipating was designed based on air-cooled radiator and circulating water flow. A temperature control system based on PC and MCU with wireless communication modules was designed. The thermoelectric cooler was driving by H-bridge circuit, whose power was controlled by PWM signal. PID algorithm was applied and average temperature was adopted to be the controlled variable. Measurement and control software on the PC and MCU was analyzed and its flow diagram was given. Influenced by centrifugal acceleration, unevenness of the temperature field would increase. A fan was mounted at the bottom of the chamber to improve the evenness of the temperature field. The experiment results show that the temperature environment with other combined environment is realized in the test chamber based on the above technology.
Design and Realization of Temperature Limiter Measurement and Control System

王恒奎,潘峰,边耐欣,陈子辰

DOI: https://doi.org/10.3969/j.issn.1000-8829.2001.05.011

2001-01-01

Abstract:The development of measurement & control system under Windows is introduced,and the system's function,design of hardware and software are discussed in detail .At the end of this paper, we think it has a wide application prospect in industry.
Study on Temperature Control System for Heat Probe Used in Cruor after Gynecologic Surgery

Caihong WEI,Sheng LEI,Guozhong ZHU,Yuquan CHEN,Min PAN

DOI: https://doi.org/10.3969/j.issn.1004-1699.2011.08.001

2011-01-01

Abstract:The temperature of heat probe must be well controlled for an efficient cruor of surgery wound and the safety of patients.This paper proposes a system including a thin film resistance temperature detector(RTD)and a bridge circuit for controlling the temperature of heat probe during the cruor after gynecologic surgery.The temperature control was achieved by a PID of which parameters were set sectionally.It is demonstrated that the proposed system can precisely and efficiently control the temperature,and circumvent the environmental effect.
[Temperature Control in a Combined Therapeutic System for Tumor].

Bin Xiong,Qi Chen,Yazhu Chen,Xuesu Feng

DOI: https://doi.org/10.3321/j.issn:1001-5515.2003.01.012

2003-01-01

Abstract:Tumor combined therapeutic system, a kind of medical instrument to restrain and kill tumor, is based on radio frequency heating technique and biological heating effect theory. It can be used solely or in combination with chemotherapy and actinotherapy for tumor hyperthermia. Combined with hardware measurement and adjustment, as well as application of the improved PID algorithm to the system of temperature control, the required accurate temperature control which directly influences the curative effect is realized. The experimental results presented in this paper demonstrated that the equipment works stably and reliably, and it is of good usefulness.
An Improved Tumour Temperature Measurement and Control Method for Superficial Tumour Ultrasound Hyperthermia Therapeutic System

G. F. Shen,Y. Z. Chen,G. X. Ren

DOI: https://doi.org/10.1088/1742-6596/48/1/122

2006-01-01

Journal of Physics Conference Series

Abstract:In tumour hyperthermia. therapy, the research on measurement and control of tumour temperature is very important. Based on the hardware platform of superficial tumour ultrasound hyperthermia therapeutic system, an improved tumour temperature measurement and control method is presented in this paper. The experiment process, data and results are discussed in detail. The improved method will greatly reduce the pain and dread of the patients during the therapy period on the tumour temperature measurement and control by using the pinhead sensor.
Design and Implement of the Resistance Furnace Temperature Control System

CAI Chun-qiao,WANG Yong-jan,Wang Jun-biao,LI Feng

DOI: https://doi.org/10.3969/j.issn.1671-1815.2007.10.050

2007-01-01

Abstract:Temperature computer control system of a resistance furnace is designed with industry person computer (IPC), temperature input module, PWM output card, solid state relay(SSR) and interrelated circuit. To achieve precise control, the PWM mode is used to control the execution component (SSR) to adjust the resistance furnace temperature. According to the one-way, large inertia and delay nature of a resistance furnace, the PID control algorithm is improved in the system. The control mode combined subparagraph PID and integral separation or integral weaken is used to realize wide range continuous regulation of the resistance furnace temperature. Thereby, it meets the needs of the resistance furnace temperatures control accuracy and control law on the complex processing of heat treatment.
Temperature Measurement System in High Power RF Current Environment

LI Dian-li,ZHOU Yu,YOU Guo-peng,SONG Cheng-li,LIU Dao-zhi,LI Xin-xiang

DOI: https://doi.org/10.3969/j.issn.1005-202X.2013.05.018

2013-01-01

Abstract:Objective:To achieve temperature measurement of the surgical site during an electrosurgical procedure,this is based on high power RF current,in order to achieve effectively control the extent of thermal damage of biological tissue.Methods:Using of electrosurgery device output characteristics,adopting intermittent measurement method;In the process of measurement,first with a K type thermocouple to achieve temperature signal into electrical signals,then using a precision thermocouple amplifier AD8495 to reach linear output of temperature and electrical signals,finally the electrical signals via conditioning and isolation circuit into PC by DAQ acquisition;Realization of data acquisition,temperature calibration,temperature display and data storage using labview software in PC.Results:Temperature measurement system based on labview virtual instrument developed to measure the temperature in the high power RF current environment is stable and effective,the measurement error is ± 1℃.Conclusions:The electrosurgical device in the living body cavity closure,welding operation of the energy is discontinuity that has a certain duty ratio,temperature measurement system is only measured when energy output is empty,although the process is not continuous,but in general can reflect the trend of temperature variation.In the use of high power RF energy to achieve pig intestine anastomosis experiments,the temperature measurement system has reached the desired measurement requirements of doctors,and establishes the foundation for the future development intelligent electrosurgery of temperature control.
Multi-channel temperature control system based on three-wire measurement and USB 2.0

Sheng-kai LIAO,Yin-nian LIU

DOI: https://doi.org/10.3969/j.issn.1000-9787.2009.02.021

2009-01-01

Abstract:The design of a multi-channel temperature control system based three-wire measurement and USB 2.0 is described.The system uses platinum resistors as temperature sensor and a 24 bitAD chip AD7713 to convert temperature signal to digital signal,heating module outputs 4 channels of PWM signal and software is based on PID theory.The system can be used independently or used with a PC through the USB interface.
[System Design of Small Intellectualized Ultrasound Hyperthermia Instrument in the LabVIEW Environment].

Feng Jiang,Jingfeng Bai,Yazhu Chen

DOI: https://doi.org/10.3321/j.issn:1001-5515.2005.04.044

2005-01-01

Journal of Biomedical Engineering

Abstract:Small-scale intellectualized medical instrument has attracted great attention in the field of biomedical engineering, and LabVIEW (Laboratory Virtual Instrument Engineering Workbench) provides a convenient environment for this application due to its inherent advantages. The principle and system structure of the hyperthermia instrument are presented. Type T thermocouples are employed as thermotransducers, whose amplifier consists of two stages, providing built-in ice point compensation and thus improving work stability over temperature. Control signals produced by specially designed circuit drive the programmable counter/timer 8254 chip to generate PWM (Pulse width modulation) wave, which is used as ultrasound radiation energy control signal. Subroutine design topics such as inner-tissue real time feedback temperature control algorithm, water temperature control in the ultrasound applicator are also described. In the cancer tissue temperature control subroutine, the authors exert new improvments to PID (Proportional Integral Differential) algorithm according to the specific demands of the system and achieve strict temperature control to the target tissue region. The system design and PID algorithm improvement have experimentally proved to be reliable and excellent, meeting the requirements of the hyperthermia system.
A thermal protective urethral heater applied to modulate the prostate cryoablation area.

B Qian,H Zhao,B Xu,M Lan

2017-01-01

Cryoletters

Abstract:BACKGROUND: Urethral warmer and cryoheater are invented and applied in cryoablation to overcome urethral cryoinjury, but these devices cannot be fixed and precisely control the released heat which excessively reduces the effective ablation area. Current warmers enlarge the operation difficulty and decrease the precision in temperature control. OBJECTIVE: A reformed catheter termed urethral heater aims to protect the urethra and simultaneously control the released heat so as to meet the aid of doctors' convenient operation in effective therapy, device fixation and precise heat controllability. MATERIALS AND METHODS: In this paper, the temperature controller combined with temperature monitor was used to control the heating behavior of the urethral heater with the initial active temperature. The controllability and thermal protection of the urethral heater was simulated and tested, which compared with that of urethral warmer. RESULTS: During the trials in vitro, the lowest temperature at the urethra surface is -3.7 degrees C when one cryoprobe was introduced in the cryoablation for 15 min and -15.3 degrees C with two cryoprobes. Above all, the effective cryoablation area increased with the decline of initial active temperatures. CONCLUSION: The urethral heater is able to prevent the urethra from irreversible damage and modulate the ablation area. The delay of heat is a new way to decline the recurrence rate and facilitate the desire of aconuresis during the cryoablation.
High Precision Temperature Controller

JQ YANG,HY ZHANG,ZQ PAN,JH CHEN,ZM ZHU,BK ZHOU

DOI: https://doi.org/10.1117/12.213001

1995-01-01

Abstract:Temperature controlling is important for optoelectronic device's stable and reliable working, especially in poor circumstance or for long time. This article represents an active temperature control system used to control the temperature of a tunable narrow-linewidth external cavity semiconductor laser. A double deck cooling structure controlled by an intelligent driver is reported and the feature of the system is investigated.
Configurable Multi-channel Temperature Control System Based on PID

LIAO Sheng-kai,LIU Yin-nian,CHEN Xiao-wen

DOI: https://doi.org/10.3969/j.issn.1002-1841.2009.06.033

2009-01-01

Abstract:The design of a configurable multi-channel temperature control system based on PID theory was described.Temperature measurement module of 64 channels,heating module output 16 channels of PWM signal and 12 channels of 0~10 V analog signal and configurable software based on PID theory were included.This system can be easily changed to meet different requirement and it was used successfully in the hot-vacuum experiment and calibration experiment of a radiometer.
Transurethral Prostatic Thermotherapy with a New Device in the Canine Prostate

Xia Xiang,Shuxia Cheng,Hu, Hanping,Zhao Gang

DOI: https://doi.org/10.1109/icbbe.2008.759

2008-01-01

Abstract:A new apparatus, different from current microwave thermotherapy ones for curing BPH, has been preliminarily devised and as well thoroughly estimated by analyzing it using heat transfer model. In this model, the Pennes bio-heat transfer equation is solved in a spherical coordinate through numerical methods, in consideration of the thermal coupling problems between the local blood perfusion rate, the values of which chosen are the results experimentally measured before, and the temperature field inside the prostate tissues. The numerical results show the similar effect with the current radio-frequency (RF) thermal therapy. In other words, the extension with significant temperature increase is nearly the one of RF therapy. However, this new apparatus possesses many advantages, simpler structure, easier operation and lower prices for example.
Temperature Measure and Control Design of Air-conditioning System Based on Digital PID

ZHANG Xin-rong,XU Bao-guo

DOI: https://doi.org/10.3969/j.issn.1002-1841.2010.10.036

2010-01-01

Abstract:This paper presented the design weather temperature measure with control system controlling algorithms and outputting and the realization of the driving circuit.Systematic composition included temperature measuring,process system,the circuit of A/D changes,systematic circuit of single-chip computer,keyboard circuit and export circuit.The function of that system can realize the regulation of output power of heating wire by control procedure of single-chip computer and one-way silicon controlled rectifier,realized the temperature control of the electric heater.The signal of temperature which gather from external environment can change into digital signal with high accuracy,and showing through the single-chip computer.In view of the characteristics of the different PID parameters with the different temperature,it selects appropriate PID parameters to control on the basis of the measured temperature.The system can run reliably in practice.
Temperature controller design for thermostat

Hong Munan,Lu Wenwen,Li Jianqiu

DOI: https://doi.org/10.3969/j.issn.1002-4956.2010.01.020

2010-01-01

Abstract:To satisfy the testing requirement of different ranges of temperature,a controller for thermostat is designed.A circuit with the functions including temperature measuring,display,alarm and control by using cheap micro-computer is presented.A thermistor is adopted to detect the change of temperature,which is transferred to change of resistance.Through a measuring circuit,the resistance change is transferred to voltage change further.The voltage is magnified and acquired by an AD converter.Temperature is calculated and displayed through three numeric display LEDs.In the meanwhile,temperature limits can be set.When temperature is out of allowed range,the corresponding equipment can be activated to ensure the temperature is within the limit.
[An Improved PID Algorithm for Temperature Control Used by Tumor Combined Therapeutic Instrument].

Hongwei Lu,Xuesu Feng,Yazhu Chen,Yanghua Ni

DOI: https://doi.org/10.3321/j.issn:1001-5515.2003.03.037

2003-01-01

Abstract:The development of a multi-functional tumor combined therapeutic instrument based on improved PID algorithm is introduced. It is based on the theory of 1 + 1 = 3 or 1 + 1 + 1 > 3 curative effect enhancement by tumor combined therapy, and it can be used solely, or with the combination of chemotherapy or actinotheraphy or both for tumor hyperthermia. By adopting improved PID temperature control algorithm, the problem of temperature control precision reduction due to process characteristics changing with different heaters was solved, thus ensuring homogeneous and smooth radio frequency heating by different heaters to intracavity tumor foci. These experiments demonstrated that the new algorithm has strong adaptability and anti-disturbance capability, the equipment works stably and reliably, and it can control therapeutic temperature precisely (+/- 0.1 degree C), which indicates a good value in clinical application.
Design of Real-Time Temperature Monitoring and Control System for Multimodal Ablation

Zou Ke,Zou Jincheng,Wang Yifei,Zhang Aili

DOI: https://doi.org/10.1007/s12204-022-2432-7

2022-01-01

Journal of Shanghai Jiaotong University (Science)

Abstract:By combining cryogenic cryotherapy and high-temperature radiofrequency therapy, multimodal ablation generates a rapidly changing temperature field in tissue by heating after pre-freezing. This method completely breaks tumour cells and releases a large amount of active antigen. Compared with the traditional single modality, the thermal physical ablation method has been shown to have a greater therapeutic effect, but it presents challenges in terms of precise monitoring and rapid control of the temperature during the treatment process. To solve this problem, we propose a temperature control system design utilizing aspects of probe sensing, real-time software and hardware signal interfaces, and dynamic compensation control strategies to accurately monitor the temperature changes during multimodal ablation treatment. The results show that the design system has millisecond-level high-speed control capability, an accuracy of 0.5 °C, and the dynamic response time is less than 0.1 s. Furthermore, the temperature fluctuation in in vivo experiments is less than 0.5 °C.
Design of the Control System for Thermal Treatment via Fuzzy Logic PID

Mingyang Song,Zhanghao Cai,Jingfeng Bai,Jianqi Sun

DOI: https://doi.org/10.1007/978-3-642-29305-4_119

2013-01-01

Abstract:The combination of cryosurgery and hyperthermia treatment has been demonstrated to be more efficient to destroy tumor tissue. A cryosurgery-hyperthermia system is designed by our group. However, the precise control of the system is difficult due to the integration. In this paper, a novel control system is proposed to ensure that the thermal system works effectively. First, the tissue temperature around the probe is regulated and kept in a desired range when radio frequency ablation is operated. Second, precise control of temperature is achieved in hyperthermia treatment using fuzzy logic PID type controller. The results of ex vivo liver experiment demonstrate that this system could provide a rather good performance with the proposed control method.
Research on Hyperthermic Perfusion Instrument for Bladder Cancer Based on Fuzzy Control Algorithm

WU Zhi-min,YE Tao,ZHU Xue-feng

DOI: https://doi.org/10.3969/j.issn.1009-2552.2012.06.007

2012-01-01

Abstract:In the recent years,hyperthermia for bladder cancer has made great progress.For treating the bladder cancer,a hyperthermia instrument is presented,which not only can achieve the objectives of medical treatment but also costs less.The paper firstly introduces the simulation system,then introduces the temperature control system based on embedded systems,and specifically presents the hardware and software design of the temperature control system.Aimed at the difficulties in building the models and the weakness on the control performance in traditional temperature control system,it presents fuzzy control algorithm.The practice results show that the fuzzy control improved the feasibility and precision of the system.The instrument system obtains good results in the simulation phase.It can be used for further clinical trials.

[Temperature Measuring and Heating Controlling in Transurethral Prostate Thermotherapy System].

Development of A Temperature Control System for Isolated Kidney Preservation Device Based on the Semiconductor Temperature Control Technology

Design of Temperature Testing System in Multi-Parameter Combined Environmental Test

Design and Realization of Temperature Limiter Measurement and Control System

Study on Temperature Control System for Heat Probe Used in Cruor after Gynecologic Surgery

[Temperature Control in a Combined Therapeutic System for Tumor].

An Improved Tumour Temperature Measurement and Control Method for Superficial Tumour Ultrasound Hyperthermia Therapeutic System

Design and Implement of the Resistance Furnace Temperature Control System

Temperature Measurement System in High Power RF Current Environment

Multi-channel temperature control system based on three-wire measurement and USB 2.0

[System Design of Small Intellectualized Ultrasound Hyperthermia Instrument in the LabVIEW Environment].

A thermal protective urethral heater applied to modulate the prostate cryoablation area.

High Precision Temperature Controller

Configurable Multi-channel Temperature Control System Based on PID

Transurethral Prostatic Thermotherapy with a New Device in the Canine Prostate

Temperature Measure and Control Design of Air-conditioning System Based on Digital PID

Temperature controller design for thermostat

[An Improved PID Algorithm for Temperature Control Used by Tumor Combined Therapeutic Instrument].

Design of Real-Time Temperature Monitoring and Control System for Multimodal Ablation

Design of the Control System for Thermal Treatment via Fuzzy Logic PID

Research on Hyperthermic Perfusion Instrument for Bladder Cancer Based on Fuzzy Control Algorithm