Abstract:OBJECTIVE:To compare the retentions of different designs of cobalt-chromium (Co-Cr), pure titanium (CP Ti), and titanium alloy (Ti-6Al-4V) removable partial denture (RPD) circumferential clasps manufactured by selective laser melting (SLM) and to analyze the stress distribution of these clasps during the removal from abutment teeth. METHODS:Clasps with clasp arm size A (1.9 mm width/1.1 mm thickness at the body and 0.8-taper) or B (1.2 times A) and 0.25 mm or 0.50 mm undercut engagement were modeled on a prepared first premolar die, named as designs A1, A2, A3, and A4, respectively. The density and elastic modulus of SLM-built Co-Cr, CP Ti, and Ti-6Al-4V were measured and given to different groups of clasps. The density, elastic modulus, and Poisson ' s ratio of enamel were given to the die. The control group was the cast Co-Cr clasp with design A1, to which the density and elastic modulus of cast Co-Cr alloy were given. The Poisson's ratio of all metals was 0.33. The initial 5 N dislodging force was applied, and the maximum displacement of the clasp along the insertion path was computed. The load was reapplied with an increment of 5 N than in the last simulation until the clasp was completely dislodged. The retentive force range of different groups of clasps was obtained. The retentive forces of the SLM-built Co-Cr, CP Ti, and Ti-6Al-4V clasps with equivalent computed retentive force range to the control group were validated through the insertion/removal experiment. The von Mises stress distributions of these three groups of SLM-built clasps under 15 N loads were analyzed. RESULTS:SLM-built Co-Cr, CP Ti, and Ti-6Al-4V clasps with designs B1 or B2, and Co-Cr clasps with design A2 had higher retentive forces than those of the control group. SLM-built CP Ti and Ti-6Al-4V clasps with design A1 had lower retentive forces than those of the control group. SLM-built Co-Cr clasp with design A1 and SLM-built CP Ti and Ti-6Al-4V clasps with design A2 had equivalent retentive forces to those of the control group. The insertion/removal experiment showed that the measured retentive forces of these three groups of SLM-built clasps were (21.57±5.41) N, (19.75±4.47) N, and (19.32±2.04) N, respectively. No statistically significant measured retentive force difference was found among these three groups of SLM-built clasps (P>0.05). The maximum von Mises stress of these three groups of SLM-built clasps exceeded their responding yield strength except for the Ti-6Al-4V one. CONCLUSION:SLM-built Co-Cr circumferential clasps had higher retention than CP Ti and Ti-6Al-4V ones with the same clasp arm size and undercut engagement. The retention of SLM-built circumferential clasps could be adjusted by changing the undercut engagement and clasp arm size. If SLM-built circumferential clasps are used in clinical practice, the Ti-6Al-4V clasp with clasp arm size A and 0.50 mm undercut engagement is recommended considering the long-term use of RPD in the patient's mouth.

[Influence of Retention-Form Design on the Retention of Resin-Bonded Fixed Partial Dentures].

Marginal fit and retention force of zirconia resin-bonded fixed dental prostheses in the posterior region with different designs

In vitro comparison of fatigue failure between conventional denture and a new type resin-bonded fixed partial denture

[Finite element analyses of retention of removable partial denture circumferential clasps manufactured by selective laser melting].

Biomechanical Analysis of Stress Distribution and Failure Risk in Mandibular Incisors Restored with Resin-Bonded Fixed Partial Dentures Using CAD/CAM Materials and Restoration Designs

[Wear Test of 4-Unit Posterior Resin Bonded Fixed Partial Dentures with Non-Rigid Connector].

Influence of the preparation design on the retentive strength of resin-bonded attachments

Evaluation of the mode of failure of abutments supporting implant-supported fixed partial dentures via different retention techniques

Validation of a shape-optimized 2-unit cantilevered inlay-retained fiber-reinforced resin-bonded dental prosthesis

[Comparison of flow conditions of adhesives and retention force of restorations among four cement-retained methods of implant-supported fixed prostheses]

Clinical audit of posterior three-unit fixed-movable resin-bonded fixed partial dentures - A retrospective, preliminary clinical investigation

[Influence of Fiber Framework Design on Fracture Strength of Posterior Glass Fiber-Reinforced-composite Resin-Bonded Fixed Partial Dentures].

Comparative Evaluation of Stress Acting on Abutment, Bone, and Connector of Different Designs of Acid-Etched Resin-Bonded Fixed Partial Dentures: Finite Element Analysis

Two-Year Clinical Trial Of Resin-Bonded Fixed Partial Dentures Incorporating Novel Attachments

Investigation of the effects of the retention groove location and dimensions of threaded glass fiber post on biomechanical responses of the restorative system

Study on Retention and Stability of Linear Occlusal Complete Dentures

Effect of Thermomechanical Dynamic Loading on the Retention of Metallic and Nonmetallic Telescopic Mandibular Overdentures

Retentive force variations in three polyamide and a polyetheretherketone denture attachments for implant-supported overdentures: An in vitro study

Retention Evaluation in zirconium bar with three different frame work Materials in implant supported mandibular overdentures (in vitro study)

Effect of connector height and retainer occlusal thickness on the fracture resistance of posterior 4-unit monolithic 5Y-TZP fixed partial dentures after thermomechanical aging

Post-treatment stability, survival time and periodontal health associated with vacuum-formed, bonded and rapid prototype retainers: A prospective clinical study