Abstract:Aim: A new, non-invasive approach suggests using single intraoral optical scanning to analyze the ridge profile of single-tooth gaps following alveolar ridge preservation in the absence of a baseline scan. This method involves creating a three-dimensional (3D) surface map to identify and assess contour changes and ridge profiles based on the adjacent teeth. Materials and methods: The present study was designed as a cross-sectional pilot analysis on a convenience sample of patients undergoing alveolar ridge preservation. Intraoral optical scans were taken on 23 patients, capturing data from 30 edentulous sites. The digital models were then imported into an image analysis software for a 3D surface defect map analysis performed by one examiner. This analysis characterized the buccolingual profile of the single tooth gap relative to the adjacent teeth. 10 linear divergence points, spaced 0.5 mm apart in a corona-apical direction, were identified at the midfacial aspect of the sites. Based on these points the sites were plotted and grouped in three different buccolingual profiles (linear, concave, and convex). Clinical parameters including Keratinized mucosa Width (KMW), and soft tissue phenotype with Colorvue biotype probes were also recorded. Results: Three different buccolingual patterns (linear, convex, and concave) were identified. Seven sites exhibited a linear profile, 10 sites displayed a concave shape, and 13 showed a convex profile. The linear profile had surface discrepancies similar to the neighboring teeth. In contrast, the convex profile revealed mid-buccal discrepancy localized only at the crestal aspect, while the concave had an extended divergence ranging from 1 to 5 mm below the soft tissue margin. Univariate and multiple logistic regression analyses did not reveal any statistically significant variables influencing profilometric analysis; however, when combining phenotype and KMW, thick phenotypes demonstrated a higher proportion of concavity (OR = 4.83) compared to thin ones, suggesting a significant trend. With every 1 mm of increase in KMW, the probability of showing a concavity decreased (p = 0.057). Conclusion: A 3D surface defect map represents a useful tool for objectively quantifying ridge defects and profiles by assessing profilometric and surface differences compared to adjacent dentition using a single intraoral scan. This method also indicates that KMW may play a critical role in preventing concavity defects. The 3D defect map can guide decision-making during soft tissue augmentation procedures by emphasizing the specific location of the defect and providing more detailed insights into its localization. These parameters can enable the tailoring of flap management and soft tissue grafting strategies to address the patient's individual needs.

Change of Polished Surface Contours on Mandibular Complete Denture Base in Different Residual Ridge Resorption Situation:A Pilot Study

[Analysis of the Difference in the Tissue Surfaces Between the Old and New Upper Complete Dentures].

Clinical study on the complete denture edge position and shape

Comparison of denture space and patient satisfaction for neutral zone versus standard‐designed digital dentures restoring mandibular resorbed ridges: A crossover randomized clinical trial

Evaluation of the influence of different build angles on the surface characteristics, accuracy, and dimensional stability of the complete denture base printed by digital light processing

3D surface defect map for assessing buccolingual profile of single tooth gaps following alveolar ridge preservation

Clinical comparative study of lingualized and anatomical occlusal pattern of complete dentures in mandible with severely ab-sorbed alveolar ridge

Influence of Buccal Emergence Profile Designs on Peri-Implant Tissues: A Randomized Controlled Trial.

Evaluation of anatomic variations of mandibular lingual concavities from cone beam computed tomography scans in a Malaysian population

Morphological Variations of the Posterior Mandible: Proposing a Classification for Ridge Morphology Based on Cone-Beam Computed Tomography Data

Layperson's Preference Regarding Orientation of Transverse Occlusal Plane from the Frontal Perspective in Fabrication of a Complete Denture: A Cross-sectional Study

[Three-Dimensional Imaging for Quantitative Evaluation of Facial Profile of Edentulous Patients Before and after Complete Dentures Restoration].

Quantitative and qualitative 3D analysis of mandibular lingual concavities: Implications for dental implant planning in the posterior mandible

Complete denture palatal rugae design impact on satisfaction and quality of life

Surface Characteristics of Milled and 3D Printed Denture Base Materials Following Polishing and Coating: An In-Vitro Study

Ridge preservation in maxillary molar extraction sites with severe periodontitis: a prospective observational clinical trial

[Pilot Evaluation of Masticatory Efficiency and Patients' Satisfaction in Long-Centric Occlusal Pattern Complete Denture Wearers].

Design of Wear Facets of Mandibular First Molar Crowns by Using Patient-Specific Motion with an Intraoral Scanner: A Clinical Study.

The Effect of Residual Dentition on the Dynamic Adjustment of Wear Facet Morphology on a Mandibular First Molar Crown

Morphological Design of Occlusal Wear Facets for the Mandibular First Molar Crown Using Different Bite Registration Methods.

Facial Aesthetic Evaluation of Rehabilitation Effects in Edentulous Patients with Varying Degrees of Residual Ridge Resorption by 3D Stereophotogrammetry.